GrizzlyメーカーH6332の使用説明書/サービス説明書
ページ先へ移動 of 20
COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN .
H6332 1 1 ⁄ 4 " Brad Nailer -1 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck - ties, rings, bracelets, or other jew- elry which may get caught in moving parts.
H6332 1 1 ⁄ 4 " Brad Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source .
H6332 1 1 ⁄ 4 " Brad Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment.
H6332 1 1 ⁄ 4 " Brad Nailer -4 - INTRODUCTION If you have any c omm ents re gard ing t his man ual, pl ease w rite to us at th e foll owing add ress : Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we st and behi nd o ur too ls.
H6332 1 1 ⁄ 4 " Brad Nailer -5 - SET UP Figure 1. Model H6332 inventory. Unpacki ng Y our M ode l H6 332 lef t our ware hous e in a c arefu lly pac ked b ox. I f you di scover th e na iler is dam age d af ter you have sig ned fo r del iver y , pl ease i mme diat ely cal l Cus tomer Ser vice a t (570) 546 - 96 63 for advic e.
H6332 1 1 ⁄ 4 " Brad Nailer -6 - Compressed Air Sy stem The Mo del H6 332 is des igne d to be oper- ated at 6 0 - 1 0 0 PS I us ing c lea n, dr y, regu - late d, c omp ress ed a ir . DO NO T exce ed th e 120 P SI m axi mum op er atin g pr es- sur e fo r you r m ode l.
H6332 1 1 ⁄ 4 " Brad Nailer -7 - Safety Nose Mechanism A s afet y mec han ism on th e nos e of th e nai ler p rotec ts a gain st ac ci den tal f irin g. Whe n the tr igg er is pres sed, t he nail er will not fire un til th e safe ty nos e me cha nis m is dep ress ed.
H6332 1 1 ⁄ 4 " Brad Nailer -8 - OPERATIONS Loadin g Figure 3. Releasing catch lever and sliding magazine pusher back. When replacing nails in your Model H6332, follow these guidelines: Gauge: 18 Length: 3 / 8 " – 1 1 ⁄ 4 " Capacity: 100 To load your nailer: 1.
H6332 1 1 ⁄ 4 " Brad Nailer -9 - 5. Pull the trigger. — If the nail drove into the wood far enough, continue with your intended operations. — If the nail either went too far or not far enough, then go to the Adjusting Depth section on this page.
H6332 1 1 ⁄ 4 " Brad Nailer -10 - 4. O pen the nailer nose by removin g the rubber nose tip, depressing the nose release mechanism , and opening the nose cover as shown in Figure 7 . Cleari ng Jammed Nails 5. D islodge the jammed nail with a tool that will fit in the slot on the unders ide of the nose.
H6332 1 1 ⁄ 4 " Brad Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u us e your nail er day i n an d day out , re pair pist ons are cheap ins uran ce agai nst wa sted d own tim e and lo st prof its, in t he event t hat a p isto n or p isto n shaf t bec ome s wo rn out .
H6332 1 1 ⁄ 4 " Brad Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od so lvent to c lean t he nos e ass emb ly of the nai ler. Alw ays be su re tha t th e n ailer is dr y befor e us ing it agai n. Do n ot all ow du st, c hip s, sa nd, etc .
H6332 1 1 ⁄ 4 " Brad Nailer -13 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trigger valve area. 1. O-rings in trigger valve hous - ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked.
H6332 1 1 ⁄ 4 " Brad Nailer -14 - H6332 PARTS BREAKDOWN .
H6332 1 1 ⁄ 4 " Brad Nailer -15 - H6332 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6332001 STEEL BALL 44 PH6332044 FIXED COVER 2 PH6332002 ORIENTATION SPRING 45 PSB15M CAP SCREW M5-.
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _______.
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street______________________________.
デバイスGrizzly H6332の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Grizzly H6332をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H6332の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H6332の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H6332で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H6332を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H6332の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H6332に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H6332デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。