GrundigメーカーCP-731iの使用説明書/サービス説明書
ページ先へ移動 of 39
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK TECHNICAL PORTGÊS Multimedia LCD Projector CP-731i USER'S MANU AL Please read this user's manual thoroughly to ensure correct usage of this projector. BEDIENUNGSANLEITUNG Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam.
ENGLISH Multimedia LCD Projector USER'S MANU AL ENGLISH-1 Thank you for purchasing this LCD projector. Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage of this projector.
ENGLISH-2 FEA TURES This multimedia LCD projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. • Outstanding brightness The UHB lamp and high-efficiency optical system assure a high level of brightness.
ENGLISH-3 B B E E F F O O R R E E U U S S E E ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH P art Names Control Panel (Refer to P.9 "OPERATIONS") Power Switch AC Inlet (to the Power Co.
ENGLISH-4 B B E E F F O O R R E E U U S S E E ( ( c c o o n n t t i i n n u u e e d d ) ) P art Names (continued) WARNING Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.
ENGLISH-5 B B E E F F O O R R E E U U S S E E ( ( c c o o n n t t i i n n u u e e d d ) ) ENGLISH Installing the Batteries Install the AA batteries into the remote control transmitter. 1. Remove the battery cover. Push the knob while lifting up the battery cover.
ENGLISH-6 INST ALLA TION Installation of the Pr ojector and Screen CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “ SAFETY INSTRUCTIONS ” and this manual. • Use the liquid crystal projector at the horizontal position only.
ENGLISH-7 ENGLISH I I N N S S T T A A L L L L A A T T I I O O N N ( ( c c o o n n t t i i n n u u e e d d ) ) Cabling RGB signal input: Connect the RGB IN 1 or 2 terminal of the projector to the RGB signal output of the computer by the enclosed RGB cable.
AUDIO IN VIDEO IN S-VIDEO IN AUDIO IN AUDIO OUT 1 12 2 USB RGB IN RGB OUT CONTROL Example of system setup Video tape recorder with S jack Video tape recorder Computer (desktop type) Computer (noteb.
ENGLISH-9 ENGLISH OPERA TIONS Switching the P ower Suppl y ON/OFF Switching Power ON 1. Check that the power cord is connected correctly. 2. Set the power switch to [ | ]. The standby mode is selected, and the Power indicator is turned to orange. 3. Press the STANDBY/ON button on the control panel or the remote control transmitter.
ENGLISH-10 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Basic Operation The Basic operations shown in Table 2 can be controlled from the projector control panel or the supplied remote control transmitter.
ENGLISH-11 ENGLISH O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Table 2. Basic Operation (continued) Item Description VOLUME Volume adjustment : Reduce VOLUME ↔ Increase VOLUME MUTE * Set/Clear Mute mode: Press the MUTE button.
ENGLISH-12 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Setup Menu The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and VIDEO/S-VIDEO input.
ENGLISH-13 ENGLISH O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Input Menu The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons.
ENGLISH-14 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Image Menu The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start operation.
ENGLISH-15 ENGLISH O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) Options Menu The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start operation.
ENGLISH-16 O O P P E E R R A A T T I I O O N N S S ( ( c c o o n n t t i i n n u u e e d d ) ) No Signal Menu The same adjustments and settings are available as with the Image and Options menus when t.
ENGLISH-17 ENGLISH WARNING • Dispose of used lamp, according to the instruction of community authorities. • Since the lamp is made of glass, do not apply shock to it and do not scratch it. • Also, do not use old lamp. This could also cause explosion of the lamp.
ENGLISH-18 M M A A I I N N T T E E N N A A N N C C E E ( ( c c o o n n t t i i n n u u e e d d ) ) Replacing the Lamp 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp.
ENGLISH-19 ENGLISH M M A A I I N N T T E E N N A A N N C C E E ( ( c c o o n n t t i i n n u u e e d d ) ) Air Filter Maintenance The air filter should be cleaned as described below at intervals of approximately 100 hours. 1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
ENGLISH-20 TR OUBLESHOO TING OSD Message The messages as described below may appear on the screen at power ON. Take the appropriate measures when such a message appears. Table 8. OSD Messages Message Contents CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME.
ENGLISH-21 ENGLISH T T R R O O U U B B L L E E S S H H O O O O T T I I N N G G ( ( c c o o n n t t i i n n u u e e d d ) ) Indicators Messa ge The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures.
ENGLISH-22 T T R R O O U U B B L L E E S S H H O O O O T T I I N N G G ( ( c c o o n n t t i i n n u u e e d d ) ) Symptom Before requesting repair, consult the following chart. If the situation cannot be corrected, then contact BOXLIGHT at 800-762-5757 or 360-779-7901.
ENGLISH-23 ENGLISH SPECIFICA TIONS NOTE : These specifications are subject to change without notice. Table 11. Specifications Item Specification Product name BOXLIGHT CP-731i LCD Projector Liquid crystal panel Panel size 2.3 cm (0.9 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoom lens F=1.
ENGLISH-24 W ARRANTY LIMITED WARRANTY BOXLIGHT CORPORATION("BOXLIGHT") warrants that each Boxlight CP-731i("the Product") sold hereunder will conform to and function in accordance with the written specifications of BOXLIGHT.
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS NORSK TECHNICAL PORTGÊS Multimedia LCD Projector CP-731i USER'S MANU AL Please read this user's manual thoroughly to ensure correct usage of this projector. BEDIENUNGSANLEITUNG Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung aufmerksam.
TECHNICAL - 1 TECHNICAL TECHNICAL Dimension Diagram 298 94.6 54 76.5 228 76 AC N Unit : mm RGB Signal Pin Assignment Pin No Signal Pin No Signal 1 Video input Red 11 - 2 Video input Green 12 RGB IN 1: SDA(DDC) 3 Video input Blue RGB IN 2: - 4 - RGB OUT: - 5 Ground 13 H.
TECHNICAL - 2 TECHNICAL Example of computer signal Resolution H × V fH (kHz) fV (Hz) Rating Signal mode Display mode 640 × 350 37.9 85.1 VESA VGA-1 Expansion 640 × 400 37.9 85.1 VESA VGA-2 Zoom in 720 × 400 37.9 85.0 VESA TEXT Zoom in 640 × 480 31.
TECHNICAL - 3 TECHNICAL T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.
TECHNICAL - 4 T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) Connection to the Mouse Contr ol 1. PS/2, ADB or Serial Mouse (1) Turn off the projector and computer, and connect the two units with the appropriate cable. For PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable.
TECHNICAL - 5 T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) TECHNICAL 1 2 3 4 1 2 3 4 + 5V – DATA + DATA GND + 5V – DATA + DATA GND 1 23 4 2 1 3 4 USB jack (B typ.
TECHNICAL - 6 T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) RS-232C comm unication (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply.
TECHNICAL - 7 T T E E C C H H N N I I C C A A L L ( ( c c o o n n t t i i n n u u e e d d ) ) TECHNICAL Requesting projector status (Get command) (1) Send the request code Header + Command data ( ‘ 02H ’ + ‘ 00H ’ + type (2 bytes) + ‘ 00H ’ + ‘ 00H ’ ) from the computer to the projector.
TECHNICAL - 8 Names Operation type Header Command data CRC Action Type Setting code Blank Color Set Red BE EF 03 06 00 3B D3 01 00 00 30 00 00 Orange BE EF 03 06 00 AB D2 01 00 00 30 01 00 Green BE EF.
TECHNICAL - 9 TECHNICAL Names Operation type Header Command data CRC Action Type Setting code Magnify Get BE EF 03 06 00 7C D2 02 00 07 30 00 00 Increment BE EF 03 06 00 1A D2 04 00 07 30 00 00 Decrem.
TECHNICAL - 10 Names Operation type Header Command data CRC Action Type Setting code Power Set OFF BE EF 03 06 00 2A D3 01 00 00 60 00 00 ON BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 1.
TECHNICAL - 11 TECHNICAL Names Operation type Header Command data CRC Action Type Setting code V.Position Get BE EF 03 06 00 0D 83 02 00 00 21 00 00 Increment BE EF 03 06 00 6B 83 04 00 00 21 00 00 Decrement BE EF 03 06 00 BA 82 05 00 00 21 00 00 H.
REGULATORY NOTICES - 1 REGULA T OR Y NO TICES WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ENGLISH-24 W ARRANTY LIMITED WARRANTY BOXLIGHT CORPORATION("BOXLIGHT") warrants that each Boxlight CP-731i("the Product") sold hereunder will conform to and function in accordance with the written specifications of BOXLIGHT.
デバイスGrundig CP-731iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grundig CP-731iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrundig CP-731iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grundig CP-731iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grundig CP-731iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grundig CP-731iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrundig CP-731iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grundig CP-731iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrundig CP-731iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
