GSWメーカーJW517の使用説明書/サービス説明書
ページ先へ移動 of 20
T ABLE OF CONTENTS I) Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 II) Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 III) Inst allation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 2 – Thank you for purchasing this water heater . Properly inst alled and maint ained, it will provide years of trouble free service. This manual gives instructions for the proper inst al- lation, safe operation and maintenance of this water heater .
– 3 – R elief V alv e R equir ements For protection against excessive pressure and/or tempera- tures, an ASME approved T emperature and Pressure (T&P) Relief V alve must be inst alled in the opening provided and labeled near the hot water outlet.
– 4 – 610mm (24 in.) MIN. FOR SER VICING 457mm (18 in.) MIN. FLUE SEE T ABLE T OP SEE T ABLE FLUE SIZES SEE T ABLE NON-COMBUSTIBLE FLOOR COMBUSTIBLE CEILING DRAFT REGULA T OR FLUE SEE T ABLE Figur.
– 5 – Figure 2 INST ALLA TION DIMENSIONS (CENTER FLUE MODELS) J W F3 07 J W F5 07 J W F6 57 J W F307 V mm 50 8 559 6 60 50 8 in. 20 2 2 26 20 mm 22 9 229 2 54 22 9 in. 9 9 10 9 mm 45 7 457 5 24 45 7 in. 18 18 20 5/8 18 mm 69 9 660 7 75 69 9 in. 27 1/2 26 30 1/2 27 1/2 mm 128 6 14 86 16 61 12 86 in.
– 6 – Air R equir ements An adequate supply of combustion and ventilation air is required to: • Ensure proper combustion. • Reduce risk of property damage, severe bodily injury or death from possible flue gas leakage and carbon monoxide emissions.
– 7 – appliances in the enclosure, freely communicating with inte- rior areas that have in turn adequate infiltration from the out- side. It shall also have a combustion air supply opening so that the tot al air received through the opening will be at least as much as would be admitted by openings having a tot al free area of 4.
– 8 – Chimney Be sure that the chimney is suf ficiently high and large enough to meet the specifications of the burner unit inst alled. Check that there is suf ficient draf t for the proper burning of oil. At least -0.015 in. (-0.381mm) water column of over-fire draf t is recommended.
– 9 – Burning Equipment (NFP A 31)” (as applicable), local codes and the manufacturer ’ s instructions. The burner should be inst alled only by a qualified Oil-Burner T echnician.
– 10 – up of lime in the T&P valve, there are two recommendations: 1. Inst all a pressure relief (only) valve in the cold water supply line. Make sure that the discharge of this valve is directed to a drain and it is protected from freezing. or: 2.
– 11 – LINE VOL T AGE THERMOST A T OR AQUAST A T® CONTROL OIL V AL VE BURNER MOT OR IGNIT OR CAD CELL LIMIT TO REMOTE ALARM CIRCUIT JUMPER ENVIRACOM™ TERMINAL L1 LIMIT L2 V AL VE CAD CELL ALARM.
– 12 – St artup MAKE SURE THA T THE HEA TER IS FULL OF W A TER. See “Filling the W ater Heater” section. DO NOT A TTEMPT T O ST ART BURNER IF ANY OF THE FOLLOWING CONDITIONS EXIST : 1. Excess oil has accumulated. 2. The unit is full of vapours.
– 13 – Wa ter T emper a tur e Re gula tion Once inst alled, the operation will be completely automatic. The thermost at (aquast at) on the water heater is adjust able and will maint ain water at the desired temperature.
W ARNING! The temperature and pressure relief valve must be manually operated at least once a year . Caution should be t aken to ensure that: 1. No one is in front of or around the outlet of the temper- ature and pressure relief valve discharge line. 2.
– 15 – • Black water can be an indication of organic cont ami- nates in the water supply . This can be problematic in areas where the water is obt ained from surface or cont- aminated sources. Organic p articles can develop bacte- rial growth, causing potential health hazards.
– 16 – 1. Shut of f the oil supply at the t ank. 2. Shut of f the cold water supply to the heater . 3. T urn "OFF" the electrical supply to the water heater . 4. Open an up st airs hot water faucet (to relieve any pres- sure). When freezing temperatures are expected: 1.
– 17 – W A TER HEA TER 8in T O 12in MAX. HOT OUTLET EXP ANSION T ANK (OPTIONAL) MIXING V AL VE COLD INLET CHECK V AL VE (IF USED REQUIRES EXP ANSION T ANK) COLD SUPPL Y HOSE BIB (OPTIONAL) FLOW CO.
– 18 – T able 1 LISTING OF OIL BURNERS. Mode l MFGR Burn er N ozz le & P u mp P re s s . Bl ast tube No t e s BE CKE T T AFG GSW - J3 037 0.75 GPH U . S. ON LY BE CKE T T AFG GSW - J3 036 0.75 GPH MA SS . ONL Y C ARLI N E Z 19 729 7AJW 31 7 0.
– 19 – Mode l MFGR Burn er N ozz le & P u mp P re s s . Bl ast tube No t e s AE RO FA FC- 2X 0.75 GPH AE RO S V - 2X 0.75 GPH AE RO FA FC- 2X 0.75 x 8 0A 5 15/16 " AE RO S V - 2X 0.75 x 8 0A 5 15/16 " BE CKE T T AFG GSW - J5 006 0.75 GPH C ANADA BE CKE T T AFG GSW - J5 032 0.
See Rating Label Serial Number prefix for W arranty Code. Reduced warranty period applies to Newfoundland. W arranty Code: P R S T U V W Y S tandard W arranty Y ears: 3 5 6 7 8 9 10 12 Reduced W arran.
デバイスGSW JW517の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
GSW JW517をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGSW JW517の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。GSW JW517の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。GSW JW517で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
GSW JW517を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGSW JW517の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、GSW JW517に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGSW JW517デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。