American DynamicsメーカーAD1202の使用説明書/サービス説明書
ページ先へ移動 of 32
Model AD1202 MCS Coax Controller Installation and Operating Instructions This manual describes the installation and operating procedures for the AD1202 MCS Coax Pan/Tilt and Lens Controller. The AD1202 Controller allows coax control of four color or monochrome cameras via the video line to the camera site.
The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION................................................................................................. 1 FEA TURES ....................................................................................................... 1 INST ALLA TION .
.
DESCRIPTION The AD1202 MCS Coax Controller is a compact Pan/Tilt, Lens, Preset Scene, and Auxiliary controller for four color or monochrome cameras. The AD1202 provides coax control of four cameras via the video line connection to the camera site.
CONNECTIONS All connections to the AD1202 Coax Controller are made on the unit’s rear panel, illustrated in Figure 2. Typical AD1202 connections with other AD units are illustrated in the Typical System Connections section at the end of this manual.
EXTERNAL Connector A 24-pin connector on the rear panel, labeled EXTERNAL, provides pins for external alarm inputs and control signals. A mating 24-pin plug-in connector with flying leads is provided.
EXTERNAL Connector (Continued) AD MANCHESTER CONTROL CODE OUTPUTS The EXTERNAL connector provides two sets of AD Manchester Control Code lines (Code 1 - pins 5 - 7, and Code 2 - pins 8 - 10) for output of camera control commands (camera pan/tilt/lens/preset/aux) to AD Manchester Control Code units, such as camera site Receivers.
FRONT PANEL CONTROLS The following front panel controls are provided for operator control of a camera site (see Figure 5). The use of these controls is described in the SETUP and OPERATION sections of this manual, pages 6 through 9.
SETUP Factory Reset The AD1202 can be reset to factory default settings which are as follows: • resets the programmed AD1202 camera inputs (see Camera Programming) to cameras 1 through 4, respective.
To program a specific camera select button for a switcher camera number: 1. Press the front panel PGM button on the AD1202. The PGM LED illuminates steadily, and the Channel Select button 1 LED flashes repeatedly. 2. Press the desired AD1202 Channel Select button for the specific camera input to be programmed.
If an input is set as unterminated, that input must be looped to a terminated video device using the lower BNC connector (see Looping Video Outputs, page 2). Coax Code Selection The AD1202 provides two different types of code output for coax control to a camera Receiver: Standard or Enhanced UTC code.
9 Calling a Preset Camera Scene A suitably equipped AD Receiver can store a maximum of 72 preset scenes. The AD1202 can call any of the first four preset scenes using the front panel PRESET buttons. See Preset Scene Programming, page 7, to program preset scenes.
.
Appendix.
BUILT-IN TEST The AD1202 has a built-in test procedure that provides a verification of AD1202 front panel controls. To operate the built-in test: 1. Remove power from the AD1202, and remove the cover from the unit. 2. Press the TEST button on the PCB while applying power to the unit.
T ypical System Connections.
TYPICAL SYSTEM CONNECTIONS AD1202 with four AD1641U Coax Receivers and Alarms REMOTE ALARM CONTACT 3 REMOTE ALARM CONTACT 4 C-2 AD1202 LOOPING VIDEO OUPUTS, ALL INPUTS UNTERMINATED REMOTE ALARM CONTAC.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1641U Coax and two AD1641M Control Code Receivers CAMERA 4 CAMERA 3 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 * 120-Ohm Terminat.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1240 Series P/Ts and two AD1641U Coax Receivers CAMERA 4 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 W B C-4 ALL INPUTS TERMINATED IN 75 Ω LOCAL MONITOR AD1641U COAX RECEIVER AD1641U COAX RECEIVER NOTE: AD1641 Series Receivers shown for illustration.
C-5 TYPICAL SYSTEM CONNECTIONS Two AD1202 Controllers with AD1408A Switcher AD1408A AUX Connector: Pin 1 - Camera ID, bit 0 Pin 2 - Camera ID, bit 1 Pin 3 - Camera ID, bit 2 Pin 4 - Ground AD1408A AD1.
.
Index.
.
AD Manchester Control Code Outputs . . . . . . . . . . . . . . . . 4 Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Response .
.
Problem Possible Causes Suggested Action Operating Problems Cannot program camera numbers or Programming Blocking feature enabled Check and enable front panel controls (page 5) preset scenes No AD1202.
.
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division Sensormatic CCTV Systems Division 1 Blue Hill Plaza 600 Bradley Hi.
SPECIFICATIONS Electrical Ratings: AD1202: 120 VAC, 50/60 Hz, 9 W ADS1202X: 230 VAC, 50/60 Hz, 50 mA Video Signal: AD1202 - EIA RS-170/NTSC Video, 525 lines @ 60 Hz ADS1202X - CCIR/PAL Video, 625 line.
デバイスAmerican Dynamics AD1202の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
American Dynamics AD1202をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmerican Dynamics AD1202の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。American Dynamics AD1202の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。American Dynamics AD1202で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
American Dynamics AD1202を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmerican Dynamics AD1202の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、American Dynamics AD1202に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmerican Dynamics AD1202デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。