American DynamicsメーカーSpeedDome Ultra VII EISの使用説明書/サービス説明書
ページ先へ移動 of 37
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 1 of 37 S peedDome ® Ultra VII EIS Day/Night Camera Dome Installation and Service Guide Figure 1.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 2 of 37 About the Camera Dome The SpeedDome Ultra VII EIS day/night camera dome ( Figure 1) comes in .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 3 of 37 Indoor Ceiling Mounting Using hardwa re shi pped with the base, the camera dome attaches directly to indoor ceilings made of sheet rock, wood, metal, or concrete ( Figure 3).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 4 of 37 Figure 4. Indoor mounting structures (option al) RHIUF B RHIUAB RHIUHC RHIU2 X2 RHIUTH RHIUTR.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 5 of 37 Outdoor Mounting (Optional) Note: This document doe s not inclu de outdoor installation and service instructions. Fo r these instructions, see RHODUL Outdoor Hou sing Install Guide 8200-0492-01.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 6 of 37 Figure 7. Outdoor mounting structures (optional).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 7 of 37 Cable Requirement s Dat a Cable The table below shows requirements for SensorNet, RS-422, and Manchester net works.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 8 of 37 T wisted Pair Adapter Figure 8. Twisted Pair Adapter The supplied ADACTP01BNC Twiste d Pair A.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 9 of 37 Power-Up Routine After power is connected to the dome, the dome performs the following hom ing routin e. 1. After a few seconds, the camera lens tilts up into the housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 10 of 37 ! WARNING! EU power requirements: This product runs o n 24Vac.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 11 of 37 Indoor Inst allation This section explains how to conn ect th e housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 12 of 37 Use the following addresses for the prot ocol s shown: PROTOCOL SW3 SW2 SW1 AD Manchester , .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 13 of 37 4. For the dome at the end of a daisy chain, set termination jumper JW1 on the dome CP U board ( Figure 13) to “terminated.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 14 of 37 6. Connect the 4-pin plug (alarm input/output) to the 4-pin receptacle ( Figu re 14). a. Feed the cable through the access hole in the base. b.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 15 of 37 Checking Power and Data for Domes Using the Base without I/O Board Check LEDs to verify that power and data are reaching the dome ( Figure 16).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 16 of 37 Manchester: After approximately 20 secon ds, the three LEDs do the followi ng: Red Green Yellow Possible Cause Blinking Steady, Blinking, then Steady 1 Steady, then Off 2 White (pin1) and black (p in 2) correctly wired.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 17 of 37 Connecting to a Mounting Base with I/O Board This procedure explains how to conne ct the housing and eyeball assembly to a mounting ba se with I/O board.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 18 of 37 4. Connect the alarm output cable, if used, to the P3 connector. Pin Color Desig nation 1 — 12Vdc (1 00mA max.) 2 — 12Vdc (1 00mA max.) 3 — Output P0 (40m A s ync.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 19 of 37 10. Set the dome address ( Figure 19 ). Figure 19.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 20 of 37 Using the Inst all/Removal T ool CAUTION: Do not use this tool to conne ct the dome to the s.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 21 of 37 Figure 21. How to use the install/removal tool Dome Connection (reverse steps to disconnect).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 22 of 37 T roubleshooting Indoor Domes CAUTION: This troublesh ooting sectio n is for indoor camera domes only! To trouble shoot outdoor domes, see install ation and service manual shipped with the outdoor h ou sin g.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 23 of 37 3. Detach dome from base an d examine address switches. Are they set correct ly ? YES If dome still doesn't respond, contact your sales representative for repair instructions .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 24 of 37 7. Observe yellow comm. LED (CR28) on I/O board ( Figure 23). Is the LED on or flashing? YES Go to s tep 8. NO Verify cable is properly attached by referring to table in step 9, page 17.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 25 of 37 Detailed Troubleshooting Use this procedure to deter mine if the problem is a simple cable conne ction or a major com pone nt. To perform this procedure, you must open the housing and eyeball assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 26 of 37 Disassembling the Dome CAUTION: Once disa ssem bled, parts of dome housing and eyeball assembly are "extremely fragile" and may break.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 27 of 37 Removing the P/S Board CAUTION: Electrostatic-se nsitive device. Use a ground strap whe n han dling power supply board. Referring to Figure 25.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 28 of 37 Removing the Slot Covers 1. Gently swivel eyeball to totally expose one of two slot covers ( Figure 27). CAUTION: Swiveling fast can damag e gears.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 29 of 37 Detaching the Eyeball 1. Perform procedure "Remo v ing the Slot Covers" (page 28). 2. Perform procedure "Remo v ing the Cam era" (this page).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 30 of 37 The following steps refer to Figure 3 4. 6. Access camera/lens board. To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 31 of 37 6. Access tilt motor. To do this, loosen captive retaining screw holding tilt cable assembly in place and gently remove this assembly. 7. Remove tilt motor ( Figure 37).
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 32 of 37 Parts List for Authorized Users The following parts can be orde red by authorized users only. To become authorized, cont act your sales representative.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 33 of 37 Figure 39. Base, housing, and eyeball assembly 33 27 28 29 30 31 32 45 44 43 42 41 34-40 Eyeball Assy.
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 34 of 37 S pecifications-Indoor Dome Operational Pan/Tilt: Manual Pan S peed.................... 0.2°-100 ° per second (scaled to zoom position) Manual Tilt Speed .
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 35 of 37 Mechanical Height ......................................................... 20.8cm (8in) Eyeball Diameter .....................................
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 36 of 37 Declarations Regulatory Compliance REG ID ............................................................... VP SDU Emissions ....................
SPEEDDOME ULTRA VII EIS DAY/NIGH T CAMERA DOME 8200-0184-14, REV. A INSTALLATION AND SERVICE GUIDE 37 of 37 Appendix A: V icon Wiring Configurations In Vicon systems where domes sup port loop through, dai sy chain the SpeedDo me Ultra VII domes off the last Vicon dome in the communicatio ns chain.
デバイスAmerican Dynamics SpeedDome Ultra VII EISの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
American Dynamics SpeedDome Ultra VII EISをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAmerican Dynamics SpeedDome Ultra VII EISの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。American Dynamics SpeedDome Ultra VII EISの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。American Dynamics SpeedDome Ultra VII EISで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
American Dynamics SpeedDome Ultra VII EISを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAmerican Dynamics SpeedDome Ultra VII EISの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、American Dynamics SpeedDome Ultra VII EISに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAmerican Dynamics SpeedDome Ultra VII EISデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
