Hand Held Productsメーカー4200の使用説明書/サービス説明書
ページ先へ移動 of 20
™ IMAGETEAM™ 4200 Hand Held Linear Imager Quick Start Guide.
Disclaimer Hand Held Products, Inc. (“Hand Held Pr oducts”) reserves the right to make changes in specifications and other in formation contained in this document without prior notice, and the reader sh ould in all cases consult Hand Held Products to determine whether any su ch changes have been made.
i Table of Contents Getting Started IT4200 with Green LED Aimer Imager Identification ............................................................. 1 Connecting the Imager for USB .............................................. 3 USB Interface Selection .
ii.
IMAGETEAM™ 4200 Quick Start Guide 1 Getting Star ted IT4200 with Green LED Aimer Imager Identification.
2 IMAGETEAM™ 4200 Quick Start Guide Reading T echniques The imager has a view finder that projects a bright red or green aiming beam that corresponds to the imager’s ho rizontal field of view. The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read.
IMAGETEAM™ 4200 Quick Start Guide 3 Connecting the Imager for USB A imager can be connected to the USB port of a computer. 1. Connect the appropriate inte rface cable to the imager. 2. Connect the other end of the cable to the computer. Note: The cable must be connected at the imager end (1) before the PC (2) end is connected.
4 IMAGETEAM™ 4200 Quick Start Guide Connecting Imager for Keyboard W edge (Powered by Host) A imager can be connect ed between the keyboard and PC as a “keyboard wedge.” The following is an exampl e of a keyboard wedge connection: 1. Turn off power to the terminal/computer.
IMAGETEAM™ 4200 Quick Start Guide 5 Connecting the Imager for RS-232 Serial Port (External Power) 1. Turn off power to the terminal/computer. 2. Connect the appropriate in terface cable to the imager. 3. Plug the serial connector into the serial port on your computer.
6 IMAGETEAM™ 4200 Quick Start Guide Useful Menu Bar Codes Manual/Serial T rigger Mode Presentation Mode Suffix Selections Resetting the S t andard Product Defaults Manual/Serial Trigger Presentation.
IMAGETEAM™ 4200 Quick Start Guide 7 T o Add a T est Code I.D. Prefix to All Symbologies Beeper and LED Sequences and Meaning Repairs User repairs and/or upgrades are not to be performed on th is product. These services are to be performed onl y by an authorized service center.
8 IMAGETEAM™ 4200 Quick Start Guide The imager’s housing may also be cleaned the same way. Inspecting Cords and Connectors Inspect the imager’s interface cable and connector for wear or other signs of damage. A badly worn cable or damage d connector may interfere with imager operation.
IMAGETEAM™ 4200 Quick Start Guide 9 T o Replace the IT4200 Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the imager’s cable from the terminal or computer. 3. Locate the small hole on the side of the imager’s handle. This is the cable release.
10 IMAGETEAM™ 4200 Quick Start Guide You need to program a suffix. Programming a suffix enables the imager to output the bar code data plus the key you need (suc h as “CR”) to enter the data into your application. The imager won’t read yo ur bar code at all.
IMAGETEAM™ 4200 Quick Start Guide 11 T echnical Support If you need assistance installing or trou bleshooting your imager, please call your Distributor or your Hand Held Pr oducts, Inc. technical support office: Asia Pacific: Telephone: Int+852-3188-3485 or 2511-3050 E-mail: aptechsupport@handheld.
12 IMAGETEAM™ 4200 Quick Start Guide Patents Please refer to the product pa ckaging for patent information. Solids and W ater Protection The IT4200 has a rating of IP41, immunity of foreign particles and dripping water. Limited W arranty Hand Held Products, Inc.
IMAGETEAM™ 4200 Quick Start Guide 13 OTHERWISE) EXCEED THE ACTUAL AMOUNT PAID TO HAND HELD PRODUCTS FOR THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HAND HELD PRODUCTS MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES.
14 IMAGETEAM™ 4200 Quick Start Guide.
.
4200-QS Rev A 9/05 Hand Held Products, Inc. 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208.
デバイスHand Held Products 4200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hand Held Products 4200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHand Held Products 4200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hand Held Products 4200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hand Held Products 4200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hand Held Products 4200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHand Held Products 4200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hand Held Products 4200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHand Held Products 4200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。