Hanns.GメーカーHW173ABBの使用説明書/サービス説明書
ページ先へ移動 of 20
HW173 HSG1044.
User’s Manual Before operating the monitor, please read this manual thoroughly. This m anual should be retained for future reference. FCC Class B Radio Fr equency Interference S tatement This equipment has been tested and found to comply with the lim its for a Class B digital device, pursuant to Part 15 of the FCC Rules.
User’s Manual RECYCLING INFORMATION We, the Hanns.G care very much about our environm ent protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User’s Manual T ABLE OF CONTENTS SAFETY NOTICE ...................................................................................................... 5 PRECAUTIONS .....................................................................................
User’s Manual SAFETY NOTICE 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any , must be used in order to comply with the emission limits.
User’s Manual SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. x Due to the nature of the fluorescent light, the screen m ay flicker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User’s Manual BEFORE OPERA TING THE MONIT OR FEA TURES x 17” W ide screen TFT Color LCD Monitor x Crisp, Clear Display for W indows x Recommended Resolutions : 1440 X 900@60Hz x EP A ENERGY ST AR .
User’s Manual INST ALLA TION INSTRUCTIONS Install Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base.
User’s Manual MAKING CONNECTIONS CONNECTING TO A PC T urn off your com puter before performing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s D-Sub port.
User’s Manual ADJUSTING THE VIEWING ANGLE x For optimal viewing it is recommended to look at the full face of the m onitor , and then adjust the monitor ’ s angle to your own preference. x Hold the stand so you do not topple the monitor when you change the monitor’ s angle.
User’s Manual OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preference.
User’s Manual FRONT P ANEL CONTROL x Power Button: Press this button to switch ON/OFF monitor ’ s power . x Power Indicator: Green — Power On mode. Orange — Power Saving mode. x MENU / RETURN: 1. T urn the OSD menu on/off or return to the previous m enu.
User’s Manual HOW TO ADJUST A SETTINGS BRIGHTNESS/CONTRAST BRIGHTNESS Adjust the brightness value of the display according to your preference. Select ψ BRIGHTNESS ω option to adjust the brightness value. CONTRAST Adjust the contrast value of the display according to your preference.
User’s Manual H-POSITION Select the ψ H-POSITION ω option to shift the screen image to the left or right. Enter the option and adjust the level. [For VGA only] V - POSITION Select the ψ V -POSITION ω option to shift the screen image up or down. Enter the option and adjust the level.
User’s Manual F ACT OR Y RESET Select the ψ F ACTOR Y RESET ω option to reset to the monitor’ s default setting. This will erase the current settings. Enter the option and select On or Of f. INFORMA TION Display Horizontal frequency/V ertical frequency/Resolution information.
User’s Manual PLUG AND PLA Y Plug & Play DDC2B Featur e This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional inform ation about its display capabilities.
User’s Manual TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User’s Manual ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User’s Manual 28 1400×1050 @60Hz 65.317 59.978 29 1440×900 @60Hz 55.469 59.901 30 1440×900 @60Hz 55.935 59.887 31 1440×900 @75Hz 70.635 74.984 19.
User’s Manual APPENDIX SPECIFICA TIONS Driving system TFT Color LCD Size 17” LCD Panel Pixel pitch 0.255mm(H) x0.255m m(V) H-Frequency 24 KHz – 80 KHz V ideo V -Frequency 55Hz– 75Hz Display Colors 16.
デバイスHanns.G HW173ABBの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hanns.G HW173ABBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHanns.G HW173ABBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hanns.G HW173ABBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hanns.G HW173ABBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hanns.G HW173ABBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHanns.G HW173ABBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hanns.G HW173ABBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHanns.G HW173ABBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。