Harbor Freight Toolsメーカー42818の使用説明書/サービス説明書
ページ先へ移動 of 15
COMPOUND SLIDE MITER COMPOUND SLIDE MITER COMPOUND SLIDE MITER COMPOUND SLIDE MITER COMPOUND SLIDE MITER SA SA SA SA SA W - 12 INCH W - 12 INCH W - 12 INCH W - 12 INCH W - 12 INCH ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .
Page 2 SKU 42818 Specifications I TEM DESCRIPT ION P owe r Consu mption 110 V A C, 60 Hz, 150 0 W at ts , 2 HP No load: 3A; Load : 6A; Star tu p : 8A P o wer Cord 7 fee t , UL appro ved, 16 A W G, po .
Page 3 SKU 42818 3. K eep children awa y . Children must ne ver be allo wed in the work area. Do not let them handle machines, tools, or extension cords. 4. Store idle equipment . When not in use, tools must be stored in a dr y location to inhibit rust.
Page 4 SKU 42818 should be carefully checked to determine that it will operate properly and perform its intended function. Chec k for alignment and binding of moving par ts; any brok en par ts or mounting fixtures; and any other condition that ma y affect proper oper ation.
Page 5 SKU 42818 11. Make adjustments safely . Unplug the pow er cord bef ore making any adjustments to the Miter Saw , or to the workpiece. Note : P erf or mance of this tool ma y vary depending on variations in local line v oltage. Exten- sion cord usage may also affect tool performance.
Page 6 SKU 42818 A uxiliar y W ood Fence T o help av oid small, shor t cut pieces of stock from being caught b y the blade or shot off , it is recommended to mount an auxiliar y wood f ence to the saw’ s metal fence . 1 . Cut a 1/2 inch thick piece of wood to match the height and length of the existing fence.
Page 7 SKU 42818 Fence Stock Correct Fence Stock Incorrect Preparation to Cut Stock 1 . Before cutting stock, verify that it fits the base and fence properly and secure in place. The photos below sho w the proper wa y to lay the stoc k on the base for cutting.
Page 8 SKU 42818 Cutting Stock 1 . Plug the P ower Cord into the electrical outlet. 2 . With the workpiece secure, turn on the saw by pressing down on the Lock-off Switch Button (64), then squeeze the Switch (70) trigger button.
Page 9 SKU 42818 4 . Pull the carriage all the way forward with the Handle (65). 5 . T ur n on the sa w by pressing do wn on the Lock-off Switch Button (64), then squeez e the Switch (70) trigger button.
Page 10 SKU 42818 7 . Remove the existing Saw Blade and replace with another 12 inch blade. The new Saw Blade has an arrow on it that must be pointing in the same direction as the large arrow on the outside of the Blade Case (31). Caution: Never use saw blades larger or smaller in diameter than 12 inches, and rated less than 5000 RPM operation.
Page 11 SKU 42818 Adjustments W arning: Always disconnect po wer to the saw bef ore making any adjustments. Adjust- ments should always be done by a qualified technician. Saw Blade Perpendicular to Fence 1 . P osition the rotating table f or a 90 degree cut.
Page 12 SKU 42818 NO TE : Some par ts are listed and shown f or illustration pur poses only and are not a vailable indi- vidually as replacement par ts. PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS DIA GRAM IN THIS MANUAL AS A REFERENCE TOOL ONL Y .
Page 13 SKU 42818 REV 11/02 REV 05/04 t r a Pn o i t p i r c s e D. y t Qt r a Pn o i t p i r c s e D. y t Qt r a Pn o i t p i r c s e D. y t Q 1 5 7 X 8 M t l o B .
Page 14 SKU 42818 Assembly Drawing Note: The V er tical Clamp is not shown. REV 11/02 REV 05/04.
Page 15 SKU 42818 REV 05/04 Note: The V er tical Clamp is not shown..
デバイスHarbor Freight Tools 42818の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 42818をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 42818の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 42818の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 42818で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 42818を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 42818の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 42818に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 42818デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
