Harbor Freight Toolsメーカー90003の使用説明書/サービス説明書
ページ先へ移動 of 16
6” BENCH GRINDER Model 90003 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at: http://www .
PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembly diagram. Keep your invoice with this manual.
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4.
11 . Dress properly . Do not wear loose clothing or jewelry . Contain long hair . Keep your hair , clothing, and gloves away from moving parts. Loose clothes, jewelry , or long hair can be caught in moving parts. 12. A void accidental starting. Be sure the Power Switch is off before plugging in.
22. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 23. Use only accessories that are recommended by the manufacturer for your model.
15. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may af fect the safe operation of this product. Replace or repair damaged or worn parts immediately .
22. Always turn off the Bench Grinder and unplug it from its electrical outlet before changing accessories or performing any inspection, mainte- nance, or cleaning procedures. 23. W ARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur .
FIGURE A SKU 90003 P AGE 8 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’ s grounding system and must never be attached to an electrically “live” terminal.
SKU 90003 P AGE 9 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord.
SKU 90003 P AGE 10 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) n o xxxx/min. A V ~ UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 15 are included.
SKU 90003 P AGE 1 1 3. Repeat Steps #1 and #2 to attach the Right T ool Rest (part #32) to the Right Wheel Guard (part #31). (See Figure D.) LEFT WHEEL GUARD (#27) RIGHT WHEEL GUARD (#31) RIGHT TOOL REST (#32) LEFT TOOL REST (#28) SCREW WITH LOCK W ASHER (#25) FIGURE D T o Attach The Spark Guards: 1.
SKU 90003 P AGE 12 T o Attach The Eye Shield Mounting Rods: 1. Insert one Screw (part #48) with a W asher (part #13) through a Bracket (part #36) and the Left Eye Shield Mounting Rod (part #49). Then, firmly tighten the Screw to secure the Left Eye Shield Mounting Rod to the body of the Bench Grinder .
SKU 90003 P AGE 13 LEFT EYE SHIELD MOUNTING ROD (#49) RIGHT EYE SHIELD MOUNTING ROD (#33) SCREW (#55) SCREW (#55) PRESSURE PLA TE (#50) PRESSURE PLA TE (#50) FIGURE G 2. There are two 1 1/32” diameter mounting holes located on the Base (part #15) of the Bench Grinder .
SKU 90003 P AGE 14 OPERA TING INSTRUCTIONS 2. Plug the Power Cord Plug (part #10) into the nearest grounded, 120 volt, electri- cal outlet. Then, turn the Power Switch (part #3) to its “ON” position and allow the Grinding Wheels (part #64) to spin up to full speed.
SKU 90003 P AGE 15 P ARTS LIST NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts.
NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90003 P AGE 16 ASSEMBL Y DIAGRAM 26 58 57 58 52 53 54 50 51 55 48 36.
デバイスHarbor Freight Tools 90003の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 90003をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 90003の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 90003の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 90003で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 90003を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 90003の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 90003に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 90003デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
