Harbor Freight Toolsメーカー95518の使用説明書/サービス説明書
ページ先へ移動 of 25
Cop yright 2007 by Harbor F reight T ools ® . All rights reser v ed. No por tion of this manual or any artwork contained herein may be reproduced in any shape or f or m without the e xpress written consent of Harbor F reight T ools. For technical questions, please call 1-800-444-3353.
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in v oice with this manual.
ELECTRICAL SAFETY 1. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any wa y . Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
in. Plugging in power equipment with the P o wer Switch on, in vites accidents. 5. Remove adjusting ke ys or wrenches before turning the po wer tool on. A wrench or a ke y that is left attached to a rotating par t of the Planer may result in personal injur y .
SPECIFIC SAFETY R ULES 1. Maintain labels and nameplates on the Planer . These carr y impor tant inf or- mation. If unreadable or missing, contact Harbor F reight T ools for a replace- ment. 2. A void unintentional starting. Make sure y ou are prepared to begin work bef ore tur ning on the Router .
12. T urn off the Planer and allow the unit to stop on its o wn if the workpiece is to be backed out of an uncompleted cut. SKU 95518 For technical questions, please call 1-800-444-3353 P A GE 6 13. Never attempt to remo ve material stuck in the mo ving par ts of the Planer while it is plugged in and running.
25. Alwa ys stand off to one side of the Planer when in use . 26. Do not reach across the Planer when it is on. SKU 95518 For technical questions, please call 1-800-444-3353 P A G E 7 27.
SKU 95518 For technical questions, please call 1-800-444-3353 P A G E 8 double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Stan- dard Association, and the National Electrical Code.
SKU 95518 For technical questions, please call 1-800-444-3353 P A G E 9 SYMBOLOGY FIGURE C UNP A CKING When unpacking, chec k to make sure all the par ts shown on the P ar ts Lists on pages 19 20, 21, and 24 are included.
3. Secure the Manual Ele vation Handle (5) with a Cap Scre w (7). (See Figure D .) 4. Inser t the Plug (6) into the Manual Ele vation Handle (5) to co v er the Cap Screw (7).
SKU 95518 For technical questions, please call 1-800-444-3353 P A GE 11 out of the P ow er Switch. The P o wer Switch cannot be turned on with the Safety K ey remo v ed. T o tur n the P ower Switch to its ON position, the Saf ety K e y must be re-inser ted in the P ow er Switch.
SKU 95518 For technical questions, please call 1-800-444-3353 P A GE 12 Rollercase 1/16” . The manual ele v ation Handle is located on the top/right side of the Planer . (See Figure H.) FIGURE H MANU AL ELEV A TION HANDLE (5) 6. Depth of Cut Gauge (131) and Scale (134): A Depth of Cut Gauge is attached to the front of the Rollercase (136).
SKU 95518 For technical questions, please call 1-800-444-3353 P A GE 13 thickness reaches 1-1/4”. NO TE: T o reset for a diff erent depth stop , raise the Rollercase (136) by about two rotations of the Manual Ele vation Handle (5). Then tur n the Thickness Pre- set Control Knob (279) to the desired position.
3. Boards longer than 24” should be suppor ted (on both the infeed and outf eed sides of the Planer) by roller stands (not included). Do not plane boards that are less than 17” long. The for ce of the cut could split the board and cause kickback. 4.
cal wiring, and any other condition that ma y aff ect its saf e operation. If abnor mal noise or vibration occurs, ha ve the prob lem corrected before fur ther use . Do not use damaged equipment. 3. T o install or rever se planing Knives (173): The Cutterhead (184) on this Planer has f our slots.
F. Rev erse the two planing Knives (173), or replace with ne w Knives and care- fully position each Knif e on the two Knif e Location Collars (185) using the Magnets (288). The Knif e Location Collars position the Knif e at the proper height. There is one Knife Location Collar at each end of the Cutterhead (184).
E. Loosen the two Head Socket Head Screws (159) on the Idler Bracket (156). Then loosen the Chain (52) by sliding the Idler Br ac ket. (See Figure P .) F. Carefully rotate the Sprock et (201) by hand to change the Rollercase (136) height. Make sure to leave the other Sprockets untouched.
TR OUBLESHOO TING P r oblem P o ss ible Ca us e P o ss ible Solut ion Gouging at ends of board. 1. Dull Knives. 2. Inadequate support of long boards. 3. Rollercase not level with base. 4. Uneven force on cutterhead. 5. Boards not butted properly. 1. Replace Knives.
P ARTS LIST - PLANER UNIT NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts.
P ARTS LIST - PLANER UNIT (CONT .) NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts. SKU 95518 For technical questions, please call 1-800-444-3353 P A GE 20 P a rt # D e scription Q ty.
P ARTS LIST - PLANER UNIT (CONT .) NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts.
ASSEMBL Y DIA GRAM - PLANER UNIT NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts.
ASSEMBL Y DIA GRAM - PLANER UNIT (CONT .) NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts.
P ARTS LIST & ASSEMBL Y DIA GRAM - MO T OR UNIT NO TE: Some par ts are listed and sho wn f or illustration purposes only , and are not av ailable individually as replacement parts.
IMPORT ANT W ARRANTY INFORMA TION SKU 95518 For technical questions, please call 1-800-444-3353 P A G E 25 Harbor F reight T ools Co. makes every effort to assure that its products meet high quality a.
デバイスHarbor Freight Tools 95518の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 95518をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 95518の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 95518の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 95518で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 95518を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 95518の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 95518に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 95518デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
