Harman-KardonメーカーAVR 430の使用説明書/サービス説明書
ページ先へ移動 of 52
430 AVR 430 AUDIO/VIDEO RECEIVER OWN ER ’ S M ANUAL Power for the Digital Revolution . ® ®.
AVR 430 AUDIO/VIDEO RECEIVER 3 Introduction 4 Safety Information 4 Unpacking 5 F ront-Panel Controls 8 Rear -Panel Connections 11 Main Remote Control Functions 15 Zone II Remote Control Functions 16 I.
INTRODUCTION Thank Y ou for Choosing Harman Kardon ® With the purchase of a Harman Kardon A VR 430, you are about to begin many years of listening enjoyment. The A VR 430 has a wide range of features and options that accommodate virtually any combination of speakers , room size and program sources .
SAFETY INFORMATION Important Safety Information V erify Line V oltage Before Use Y our A VR 430 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.
FRONT-PANEL CONTROLS 1 Standby/On Switch 2 Surround Mode Group Selector 3 Surround Mode Selector 4 T uning Selector 5 T uner Band Selector 6 Preset Station Selector 7 Input Source Selector 8 T uning M.
FRONT-PANEL CONTROLS 6 FRONT-PANEL CONTROLS 4 T uning Selector: Press the left side of the button to tune lower -frequency stations and the right side of the button to tune higher -frequency stations . When the tuner is in the MANUAL/MONO mode , each tap of the Selector will increase or decrease the frequency by one increment.
FRONT-PANEL CONTROLS FRONT-PANEL CONTROLS 7 The following controls and jacks are located behind the front-panel door . T o open the door , place the edge of a finger on the left or right edge of the panel and gently swing the door down towards you. A Main Power Switch: Press this switch to apply power to the A VR 430.
8 REAR-PANEL CONNECTIONS REAR-PANEL CONNECTIONS ¡ AM Antenna ™ FM Antenna £ Preamp Outputs ¢ Subwoofer Output ∞ A-BUS Connector § Surround Speaker Outputs ¶ F ront Speaker Outputs • F an V .
REAR-PANEL CONNECTIONS 9 REAR-PANEL CONNECTIONS ¡ AM Antenna: Connect the AM loop antenna sup- plied with the receiver to these terminals . If an external AM antenna is used, make connections to t he AM and GND terminals in accordance with the instructions sup- plied with the antenna.
REAR-PANEL CONNECTIONS 10 REAR-PANEL CONNECTIONS g Remote IR Input: If the A VR 430’s front-panel IR sensor is blocked due to cabinet doors or other obstructions , an external IR sensor may be used.
MA IN REMOTE CONTROL FUNCTIONS MAIN REMOTE CONTROL FUNCTIONS 11 MAIN REMOTE CONTROL FUNCTIONS 11 0 P ower Off Button 1 P ower On Button 2 LCD Information Display 3 Input Selectors 4 AV R Selector 5 T .
12 MAIN REMOTE CONTROL FUNCTIONS MA IN REMOTE CONTROL FUNCTIONS IMPORT ANT NOTE: The A VR 430’ s remote may be programmed to control up to eight devices , including the A VR 430. Before using the remote , it is important to remember to press the Input Selector Button 3 that corresponds to the unit you wish to operate .
MAIN REMOTE CONTROL FUNCTIONS 13 MA IN REMOTE CONTROL FUNCTIONS MAIN REMOTE CONTROL FUNCTIONS 13 s T ransport Fast-Play/Scan Buttons: These but- tons have no direct function on the A VR 430, but they are used when the remote is programmed for a com- patible DVD , CD or tape player .
MA IN REMOTE CONTROL FUNCTIONS Memory Button: Press this button to enter a radio station to the A VR 430’s preset memory . First, tune the desired station, and then press this button.
ZONE II REMOTE CONTROL FUNCTIONS å Po wer Off Button: When used in the room where the A VR 430 is located, press this button to place the unit in Standby . When it is used in a remote room with a sensor that is connected to the Multiroom IR Input f jack, this button turns the Multiroom system on and off .
INSTALLATION AND CONNECTIONS System Installation After unpacking the unit, locating it in a place with ade- quate ventilation and placing it on a solid surface capable of supporting its weight, you will need to make the con- nections to your audio and video equipment.
INSTALLATION AND CONNECTIONS 17 INSTALLATION AND CONNECTIONS 5. Connect the Video Monitor Output › jacks on the receiver to the composite or S-Video input of your television monitor or video projector . 6. If your DVD Player has Y/Pr/Pb analog component video outputs , connect them to the Component Video 1 Inputs c .
18 INSTALLATION AND CONNECTIONS INSTALLATION AND CONNECTIONS RS-232 Connections The A VR 430 is equipped with an RS-232 Serial Connection Port e that may be used for two pur- poses .
SYSTEM CONFIGURATION 19 SYSTEM CONFIGURATION When all audio , video and system connections have been made , there are a few configuration adjustments that must be made . A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience .
20 SYSTEM CONFIGURATION SYSTEM CONFIGURATION 3. Carefully remove the protective plastic film from the front-panel lens . If left in place , the film will prevent proper operation of the remote control. 4. Install the four supplied AAA batteries in the remote as shown.
SYSTEM CONFIGURATION 21 SYSTEM CONFIGURATION SYSTEM CONFIGURATION 21 When using the full-OSD system to make the setup adjustments , press the OSD Button once so that the MASTER MENU (Figure 1) appears . The ➔ cursor will be next to the INPUT SETUP line .
SYSTEM CONFIGURATION 22 SYSTEM CONFIGURATION 22 SYSTEM CONFIGURATION are processed at their native sample rate . F or example , a 48kHz digital source will be processed at 48kHz. However , the A VR 430 allows you to upsample the incoming 48kHz signals to 96kHz for added resolution.
SYSTEM CONFIGURATION SYSTEM CONFIGURATION SYSTEM CONFIGURATION 23 SYSTEM CONFIGURATION 23 On the DTS menu, the selection choices made with the ‹ / › Na vigation Button o on the remote are determined by a combination of the type of program material in use and whether the 5.
SYSTEM CONFIGURATION SYSTEM CONFIGURATION 24 SYSTEM CONFIGURATION 24 SYSTEM CONFIGURATION When you have completed your selection for the front channel, press the ¤ Navigation Button o on the remote to move the cursor to CENTER .
SYSTEM CONFIGURATION SYSTEM CONFIGURATION SYSTEM CONFIGURATION 25 SYSTEM CONFIGURATION 25 Note that when any speaker group other than the front left/right speakers is set to LARGE , the crossover may not be adjusted, as the feed will be full-range , with no sound being derived for the subwoofer at that position.
SYSTEM CONFIGURATION SYSTEM CONFIGURATION 26 SYSTEM CONFIGURATION 26 SYSTEM CONFIGURATION Navigation Button o to retur n the ➔ cursor to the FL position. With the on-screen ➔ cursor pointing to FL , press the ‹ / › Na vigation Button o until the distance from the center speaker to the preferred listening position is entered.
SYSTEM CONFIGURATION SYSTEM CONFIGURATION SYSTEM CONFIGURATION 27 SYSTEM CONFIGURATION 27 Figure 11 • The channel position being adjusted will flash in the Speaker/Channel Input Indicators @ . If the test noise is heard from a channel other than the one shown in the indicator , there is an error in the speaker connections .
SYSTEM CONFIGURATION SYSTEM CONFIGURATION 28 SYSTEM CONFIGURATION 28 SYSTEM CONFIGURATION The output levels may also be adjusted at any time using the remote control and semi-OSD system. T o adjust the output levels in this fashion, press the T est Button f .
OPERATION Basic Operation Once you have completed the initial setup and configu- ration of the A VR 430, it is simple to operate and enjoy . The following instructions will help you maximize the enjoy.
OPERATION 30 OPERATION Lower Display Line $ . Next, use the ⁄ / ¤ Navigation Button o on the remote or the ‹ / › Button on the front panel H to change the setting as desired. The unit will retur n to normal operation within five seconds after the setting is changed.
OPERATION OPERATION 31 Surround Mode Chart MODE FEA TURES Dolby Digital Available only with digital input sources encoded with Dolby Digital data. It provides up to five separate main audio channels and a special dedicated low-frequency effects channel.
OPERATION 32 OPERATION owner’s manual for your DVD player for more informa- tion on making these settings . Selecting a Digital Source To utilize either digital mode , you must have properly connected a digital source to the A VR 430.
OPERATION These indicators are the L/C/R/LFE/SL/SR/SBL/SBR letters that are inside the center boxes of the Speaker/Channel Input Indicators @ on the front- panel. When a standard analog signal is in use , only the “L ” and “R” indicators will light, as analog signals have only left and right channels .
OPERATION 34 OPERATION AM and FM so that the desired frequency band is selected. 3. Press the T uning Mode Selector 8 l to select manual or automatic tuning .
OPERATION 35 OPERATION OPERATION highlighted. After the levels are reset, resume the pro- cedure outlined above to reset the levels to the desired settings .
36 ADVANCED FEATURES ADVANCED FEATURES The A VR 430 is equipped with a number of advanced features that add extra flexibility to the unit’s operation. While it is not necessary to use these features to operate the unit, they provide additional options that you may wish to use .
ADVANCED FEATURES ADVANCED FEATURES 37 NOTE: Since the setting for the turn-on volume can- not be heard while the setting is being made , you may wish to determine the setting before making the adjustment. T o do this , listen to any source and adjust the volume to the desired level using the regular V olume Controls )r î .
38 MULTIROOM OPERATION MULTIROOM OPERATION The A VR 430 is fully equipped to operate as the con- trol center for a complete multiroom system that is capable of sending one source to a second zone in the house while a separate source is listened to in the main room.
MULTIROOM OPERATION MULTIROOM OPERATION 39 MULTI ON . Press the Set Button q again to activate the setting . Note that this method may be used to turn the Multiroom system on or off even when the A VR is in the Standby mode in the main listening room.
The A VR 430 remote is factory-programmed for all functions needed to operate the unit. In addition, it is also preprogrammed to operate most recent Harman Kardon DVD players and changers , CD players and changers , CD recorders and cassette decks .
or too old, and thus not all of its commands will be in the code library . Y ou may fill in the codes for any button that does not operate properly by using the learning technique shown on page 41.
screen, as shown in Figure 28. Press the Set Button q to begin the process of learning commands from another device’s remote into the A VR remote . Figure 28 3.
“TV , ” and show how to change it to take on the codes for operating a VCR. When that device’s name appears , press the Set Button q . Figure 37 4. Once the “old” device type has been selected, you need to tell the remote which set of remote codes to use as a replacement for the device just selected.
you must first press the Input Selectors d for that button, and then press the Command or Function key . Since we want to pro gram a series of events that occur each time the Power On button is pressed, press the A VR button. In your specific macro , this is the first command button.
next to the bracketed read-out of the underlying device (e .g ., [AVR] POWER ON ). 6. When you are finished reviewing the macro’s contents , press the Set Button q to return the remote to normal operation.
Button o until the desired device name appears to the right of the device in use . In our example , that is the cable box. When the desired combination of devices appears , press the Set Button q .
3. At the next menu screen (Figure 67) press the ⁄ / ¤ Navigation Buttons o once so that E Z S ET DISABLE appears in the lower line of the LCD display . Figure 67 4. Within five seconds , press the Set Button q to disable the SPL Select Button .
Renaming Individual Keys Thanks to the programming flexibility of the A VR remote , an individual button on the remote may be assigned a feature or function that is different from the name that appears as the factory default when the button is pressed.
any settings you had previously made will have to be reentered. To erase all settings and reset the remote to the original factory default settings and displays , follow these steps: 1. Press and hold the Program Button O for about three seconds while the message shown in Figure 17 appears in the remote’s LCD Information Display 2 .
SYMPTOM CAUSE SOLUTION Unit does not function when Main • No AC P ower • Make certain AC power cord is plugged into P ower Switch is pushed a live outlet • Check to see whether outlet is switch-.
AVR 430 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average P ower (FTC) 80 W atts per channel, 20Hz–20kHz, @ <0.07% THD , both channels driven into 8 ohms Seven-Channel Surround Modes P ower per Individual Channel F ront L&R channels: 65 W atts per channel @ <0.
® 250 Crossways Park Drive , Woodbury , New Y ork 11797 www .harmankardon.com © 2003 Harman International Industries , Incorporated P art No . ZK-C10-01HA-00.
デバイスHarman-Kardon AVR 430の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harman-Kardon AVR 430をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarman-Kardon AVR 430の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harman-Kardon AVR 430の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harman-Kardon AVR 430で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harman-Kardon AVR 430を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarman-Kardon AVR 430の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harman-Kardon AVR 430に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarman-Kardon AVR 430デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
