Harmar MobilityメーカーAL030の使用説明書/サービス説明書
ページ先へ移動 of 16
M OB I LI TY M O B I L I T Y M O B I L I T Y AL010 MICRO SCOOTER LIFT AL030 POWER TOTE MANUAL WHEELCHAIR LIFT INST ALLA TION GUIDE & OWNER'S MANUAL AL010 Micro Scooter Lift AL030 Power T ote for Manual Wheelchairs Congratulations on your new lift purchase.
Section 1 - Unpacking the Lift Your Universal Out side Lift was factory pre-assembled to require little assembly before installation. Box contents should include: AL010 - Micro Scooter Lift LIFT BODY .
Section 2 - Wiring the Vehicle Important Note: IMPROPER WIRING IS THE #1 CAUSE OF PROBLEMS IN THE OPERATION OF A VEHICLE LIFT . FOLLOW THE WIRING INSTRUCTIONS CAREFULLY Located in the hardware package is the vehicle wiring harness. The harness is manufactured to, and complies with the SAE J1128 requirements.
Section 3 - Vehicle Preparation T o install the lift on a vehicle, it must be capable of accepting a hitch. If you are unsure about the hitch required, there are different places for you to check. Hitch Shops - Check your local area for shops that specialize in trailer hitches.
Measure from Hitch Bar to ground 5-13" 13-15" 15-17" 17-19" Section 4 - Installing the Lift ( no Swing A way option ) Your lif t will come shipped to you factory pre-assembled.
Measure from Hitch Bar to ground 5-12" 12-14" 14-16" 16-18" Drawings below depict a Class 3 Hitch Adapter The installation for a Class 2 is identical Move the folded lift to the rear of the vehicle with the motor box folded away from the vehicle.
2 Push bottom of bracket 3 While holding bottom of bracket, rotate handle 4 Finish rotating handle, aligning holes 5 Install safety pin LOCKED NOT LOCKED YES NO NO Section 6 - Operating the Swing Away Option Many scooter and chair owners require access to the rear of a vehicle.
ON DOWN UP "PLA TFORM KEEPER" W EL DE D TO PL A TF O RM Section 7 - Operating the AL010 Micro Scooter Lift Insert Key and switch to "ON" position Press down on T oggle switch momentarily . Once platform has been lowered at least an inch, unfold the platform.
LOADING YOUR SCOOTER ON THE LIFT Turn ON the power switch with the key furnished with your lift. Lower the platform using the UP/DOWN toggle switch. Pushing the switch downward will cause the platform to lower. Unfold the platform, then continue lowering to the ground.
ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch. WE LD ED TO PLAT FO RM Insert Key and switch to "ON" position Press down on T oggle switch momentarily .
Section 8 - Operating the AL030 Power T ote for Manual Wheelchairs LOADING YOUR WHEELCHAIR ON THE LIFT Turn ON the power switch with the key furnished with your lift. Lower the platform using the UP/DOWN toggle switch. Pushing the switch downward will cause the platform to lower.
Loosen nuts here Slide arm up or down tube Tighten after adjustment Section 9 - Adjusting the AL010 and AL030 N O I S N E T T S U J D A N O I S N E T T S U J D A N O I S N E T T S U J D A N O I S N E .
Section 10 - Safety & Maintenance SAFETY : Caution: Keep hands away from PINCH POINTS. As with most mechanical objects, the hinge point of a moving part creates a pinch point. Be sure to not to stick fingers or extremities at or near these points.
Section 11 T roubleshooting guide The lift does not operate Check the power supply. The wiring harness ( both wires ) must be run directly to the battery . Attaching the black ( ground ) wire to the frame of the vehicle is NOT considered a reliable ground.
ITE M # DESCRIP TIO N PART # 1 SWIT CH PLAT E ALA12055 2 TOGGLE SWITCH ALA12010 3 KEY SWIT CH ALA12015 4 MOTOR COVER ALA12050 5 ACTUATOR ALA10010 6 OUT ER T UBE - AL01 0 ALA0103 7 HOLD DOW N ARM - A L.
16 15 14 + KEYSWITCH ACTUATOR 12V POLE REVERSING SWITCH BATTERY TRAILER PLUG MOTOR COVER LIGHT B R OW N CIRCUIT BREAKER VEHICLE HARNESS ITE M # DESCRI PTI ON PART # 1 SWIT CH PLAT E ALA12055 2 TOGGLE .
デバイスHarmar Mobility AL030の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Harmar Mobility AL030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarmar Mobility AL030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harmar Mobility AL030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harmar Mobility AL030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harmar Mobility AL030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarmar Mobility AL030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harmar Mobility AL030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarmar Mobility AL030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。