Havis-ShieldsメーカーKK-100-06の使用説明書/サービス説明書
ページ先へ移動 of 22
INSTALL INSTRUCTIONS KK-100-06 & KK-120-06 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PR ISONER TRANSPORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”Air Ra.
KK-XXX-06_INST_8-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head scr.
KK-XXX-06_INST_8-07 3 Rear OEM Trim modifications 1997-2 007 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at th e rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in phot o.
KK-XXX-06_INST_8-07 4 Ford Driver-Side rear Ford Passenger-Side rear 8”inches 8” inches Note: Photos above show a Chevrolet Van. Photos ar e intended to show rubber floor mat option only. ***Kwik kits are designed for cargo vans with no rear OEM trim, however they can be installed into passenger window vans.
KK-XXX-06_INST_8-07 5 1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet.
KK-XXX-06_INST_8-07 6 Remove all black hardw are from asse mbled unit. This will give you the subassemblies as they are shown on the follow ing pages..
KK-XXX-06_INST_8-07 7 The following photos are the main subassemb lies as they are shipped from the factory. Remove drawing on final page and referen ce the item #’s as you install this kit.
KK-XXX-06_INST_8-07 8 KWIK KIT LAYOUT Diamond plate floor and ceiling sections are not shown for detail purposes. 3 rd Compartment ceiling Item #12 Rear bulkhead/door assembly Item #6 3 r d Compartmen.
KK-XXX-06_INST_8-07 9 VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is s ever ely limited after kit is installed. If optional rear load light(s) (KK-RLL) was ordered, install at this time.
KK-XXX-06_INST_8-07 10 Place Driver-side Bench/Wall assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pin.
KK-XXX-06_INST_8-07 11 Current view of installa tion Place Center Divider into vehicle. Item #5 Item #4 Item #3 Approximate center Item #5 Carefully place Driver-side Ceiling section into vehicle. Item #7 Loosely bolt Center Divider to Front Bulkhead Item #5 to #3 Place (2) Diamond Plate Floors between Bench/Wall assemblies and Front bulkhead .
KK-XXX-06_INST_8-07 12 Remove screws holding the center divider together where 3 rd Compartment Bulkhead will be mounted. Item #5 Position 3 rd Compartment Ceiling into vehicle. Item #12 Current view of installa tion Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc.
Place 3 rd compartment bench Photo shows optional storage door Note: Be careful not to scratch bulkheads. Item #10 Item #10 to #9 Bolt 3 rd Compartment Bench to 3 rd Compartment Divider using ¼” x ¾” carriage bolts and serrated nuts.
KK-XXX-06_INST_8-07 14 Item #6 to #5 Item #6 Item #6 Place Rear Bulkhead Doorframe into vehicle Position between Driver and Passenger-side Bench/Wall assemblies Loosely attach Doorframe to Center divider using #10 x 3/8” flat head machine screws and nylock nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembly .
KK-XXX-06_INST_8-07 15 An awe or scribe will help align the holes THE FOLLOWING STEPS AR E EXTREMLY CRITI CAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY.
KK-XXX-06_INST_8-07 16 Top Passenger-Side rear Top Driver-Side rear Item #6 Approximately 3”inches Item #6 3” inches Item #7 to #1 Item #6 Item #6 Position Driver-side Ceiling section to mate with Bench/Wall assem bly. Pre- drill 5/32” holes into Ceiling, using Bench/Wall assembly holes as a guide.
Begin to tighten ALL loose hardware on the remainder of the unit, being sure to align edges and bends of materials being tightened. This will square the unit to itself.
KK-XXX-06_INST_8-07 18 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed e arlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts.
KK-XXX-06_INST_8-07 19 Socket Ball Item #14 to doors and frames Attach Ball & Socket Style Doorstop. 1 st Attach “Ball” portion of assembly. Attach to threaded hole on the doo r using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and brack et portion.
KK-XXX-06_INST_8-07 20 Optional Storage Compartm ent (Sold Seperatley) FINAL INSTALLATION PHOTOS Optional Storage Compartm ent (Sold Separately).
KK-XXX-06_INST_8-07 21 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 K K -RLL KK-PV ENT K R -CCL-1 KR-DL PRISONER TRANSPORT OPTIONS – (A ll SOLD SEPERATLEY ).
Item 3 Item 7 Item 12 Item 1 Item 8 Item 10 Item 6 Item 2 Item 4 Item 9 Item 11 Item 14 Item 15 Item 5 Item 14 Item 13 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bul.
デバイスHavis-Shields KK-100-06の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Havis-Shields KK-100-06をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHavis-Shields KK-100-06の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Havis-Shields KK-100-06の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Havis-Shields KK-100-06で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Havis-Shields KK-100-06を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHavis-Shields KK-100-06の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Havis-Shields KK-100-06に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHavis-Shields KK-100-06デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
