Havis-ShieldsメーカーKwik-Kit KK-100-03の使用説明書/サービス説明書
ページ先へ移動 of 20
INSTALL INSTRUCTIONS KK-100-03 & KK-120-03 KWIK-KIT PRIS ONER TRAN SPORT INSERT FORD and CHEVY V AN PRIS ONER T RANSP ORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”A.
KK-XXX-03_INST _10-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phi llips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” P hillips flat head.
KK-XXX-03_INST _10-07 3 Rear O EM Trim modifications 1997 -2008 Chevrolet G-Se ries Va n Installatio n of Kwik Kit is very similar in Fo rd and Chevy Van s. All kits start with a measure ment at the rea r floor. The rear plas tic flo or tri m on Chevy van s must b e cut straigh t across as sh own in p hoto.
KK-XXX-03_INST _10-07 4 3. PASSENGER WINDOW VAN PREPARATIONS: Note: Kwik Kits are reco mmended for Cargo Vans . The installer must determine modif ications to the interior of a wi ndow van. 1. Remove all rear bench se ats from the vehicle. 2. Modify / remove interior parts as need ed.
KK-XXX-03_INST _10-07 5 1. Remove clear shrink-wra p covering from prisoner transport assem bly. 2. This is the 3 rd compartment, 40 section 3. Rem ove all black hardware, wood fillers, and brackets holding assembli es. 4. Remove bolts holdi ng the kit to the wood pallet.
KK-XXX-03_INST _10-07 6 Remove all black hardware from assem bled unit. This will give you the subassemblies as they are shown on the followin g pages.
KK-XXX-03_INST _10-07 7 VERY IM PORTANT: Be sure tha t all Aux iliary lig hting, vid eo systems, Kwi k kit o ptions, a nd wiring a re comple te. Access is severely li mited after k it is insta lled. If optional rear load li ght(s) (KK-RLL) was ordered, in stall at this time.
KK-XXX-03_INST _10-07 8 Place Driver - side Bench/Wal l assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pi n.
KK-XXX-03_INST _10-07 9 Current view of installati on Place Center Divider into vehicle. Item #5 Item #4 Item #3 NOTE: Some installers prefer to install ceiling prior to divider .
KK-XXX-03_INST _10-07 10 Item #9 Remove Bulkhead Emergenc y Exit Hatches to ease installati on. Item #9 Route dome light wires, HVAC hoses, video cables, etc t o their respective locations Item #8 Pla.
KK-XXX-03_INST _10-07 11 Rear Facing bench Bolt side door and door-frame assembly using ¼” x ¾” carriage bolts, washers and nuts. Loosely bolt Passenger-si de rear ceilings, Bench/W all assembly to Middle Bulkhead usin g ¼” x ¾” Carriage bolts and serrated nuts Note: An awe or scribe is r ecommended to help align holes.
KK-XXX-03_INST _10-07 12 Loosely bolt Rear Bulk head Doorframe ( at the door hinge) to Bench/Wall assemblies using ¼” x ¾” carriage bolts, washers and serrated nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembl y .
KK-XXX-03_INST _10-07 13 An awe or scribe will help align the holes THE FOLLOWING STEPS ARE EXTREMLY CRITICAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUC TIONS CAREFULLY.
KK-XXX-03_INST _10-07 14 Position Driver - side Ceiling section to mate with Bench/Wal l assembly. Pre- drill 5/32” holes into Ceiling, using Bench/Wall assemb ly holes as a guide.
KK-XXX-03_INST _10-07 15 Begin to tighten ALL loose hardware on the rem ainder of the unit, b eing sure to align edges and bends of mate rials being tightened.
KK-XXX-03_INST _10-07 16 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed earlier. Dril l 3/8” holes through the do orframe, floor, and vehicle. Attach using 3/8 ” x 2” hex head bolts, washers, fender wash ers, lock washers, and hex nuts .
KK-XXX-03_INST _10-07 17 Silicone all seems and joints. This wil l allow the unit to be hosed out. In the upper corner of ea ch side of the 3 rd Compartment Doorframe are small filler panels that need to be inst alled. Attach using ¼” x ¾” carriage bolts, washers, and serrated nuts.
KK-XXX-03_INST _10-07 18 FINAL INSTALLATION PHOTOS Optional Stora ge Compartment (Sold Separately) Forward Compartment for m odels KK-100-03, KK-100-04, KK-120-03 and K K-120-04.
KK-XXX-03_INST _10-07 19 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 KK - RLL KK-PVENT KR - CCL - 1 KR-DL PRISONER TRANSPORT OPTIONS – (All SOLD SEPERATLEY ).
ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bulkhead 4 Diamond-plate F loor 5 Divider 6 Rear Bu lkhead/ Doorframe 7 Driver-side Rear Ceiling 8 Passenger-side Rear Cei.
デバイスHavis-Shields Kwik-Kit KK-100-03の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Havis-Shields Kwik-Kit KK-100-03をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHavis-Shields Kwik-Kit KK-100-03の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Havis-Shields Kwik-Kit KK-100-03の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Havis-Shields Kwik-Kit KK-100-03で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Havis-Shields Kwik-Kit KK-100-03を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHavis-Shields Kwik-Kit KK-100-03の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Havis-Shields Kwik-Kit KK-100-03に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHavis-Shields Kwik-Kit KK-100-03デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
