Havis-ShieldsメーカーKwik-Kit KK-100-05の使用説明書/サービス説明書
ページ先へ移動 of 22
INSTALL INSTRUCTIONS KK-100-05 & KK-120-05 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PR ISONER TRANSPORT TOOLS REQUIRED: ¼” & 3/8” Ratcheting Wrenches ¼” & 3/8”Air Ra.
KK-XXX-05_INST_8-07 2 40” COMPARTMENT (cont): QTY DESCRIPTION PART # USED FOR: 40 #10 x 1” Phillips pan head sheet metal screw GSM33196 Floor, wall to ceiling 25 #8 x 3/8” Phillips flat head scr.
Rear OEM Trim modifications 1997-2007 Chevrolet G-Series Van Installation of Kwik Kit is very similar in Ford and Chevy Vans. All kits start with a measurement at th e rear floor. The rear plastic floor trim on Chevy vans must be cut straight across as shown in phot o.
KK-XXX-05_INST_8-07 4 Ford Van Driver-Side rear Ford Van Passenger-Side rear PASSENGER WINDOW VAN PREPARATIONS: 1. Remove all rear bench seats from the vehicle. 2. Modify / remove interior parts as needed. 3. Remove floor mat/carpet and replace with ½” plywood or sound deadening m aterial.
KK-XXX-05_INST_8-07 5 1. Remove clear shrink- wrap covering the prisoner transport assembly. 2. This is the rear 40/60/or 80 section of the kit. 3. Remove all black hardware, wood panels and brackets holding wood panels. 4. Remove bolts holding the kit to the wood pallet.
KK-XXX-05_INST_8-07 6 Remove all black hardw are from asse mbled unit. This will give you the subassemblies as they are shown on the follow ing pages..
KK-XXX-05_INST_8-07 7 The following photos are the main subassemb lies as they are shipped from the factory. Remove drawing on final page and referen ce the item #’s as you install this kit.
KK-XXX-05_INST_8-07 8 Item #12 Rear bulkhead/door assembly Item #6 3 r d Compartment Bulkhead/door assembly Item #11 3 rd Compartment ceiling KWIK KIT LAYOUT Diamond plate floor and ceiling sections are not shown for detail purposes.
KK-XXX-05_INST_8-07 9 VERY IMPORTANT: Be sure that all Auxiliary lighting, video systems, Kwik kit options, and wiring are complete. Access is s ever ely limited after kit is installed. For neatness of wiring, route all cables down driver-s ide “B” pillar.
KK-XXX-05_INST_8-07 10 Place Driver-side Bench/Wall assembly into van so bench rests on wheel well Item #1 Remove steel support bracket for Emergency Exit Hatch pin.
Item #4 & #13 Place (2) Diamond Plate Floors between Bench/Wall assemblies and Front bulkhead . Place cardboard along side of bench while positioning Be careful that exposed wires are not touching metal and optional KK- x-VAK hoses are not completely crushed Note: Vent hose will be tight in spot s.
KK-XXX-05_INST_8-07 12 Remove screws holding the center divider together where 3 rd Compartment Bulkhead will be mounted. Item #5 Position 3 rd Compartment Ceiling into vehicle. Item #12 Current view of installa tion Slide the ceiling sections out of the way in order to access A/C hoses, wires, etc.
Re-install screws removed in step above and loosely attach aligning all three materials. Note: An awe or scribe is recommended to help align holes Item #9 to #5 Place 3 rd compartment bench Photo shows optional storage door Note: Be careful not to scratch bulkheads.
KK-XXX-05_INST_8-07 14 Loosely bolt Rear Bulkhead Doorframe ( at the door hinge) to Bench/Wall assemblies using ¼” x ¾” carriage bolts, washers and serrated nuts Item #6 to #2 Place the 3 rd Compartment Doorframe assembly .
KK-XXX-05_INST_8-07 15 An awe or scribe will help align the holes THE FOLLOWING STEPS AR E EXTREMLY CRITI CAL FOR A SUCCESFULL INSTALLATION! PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY.
KK-XXX-05_INST_8-07 16 Top Passenger-Side rear Top Driver-Side rear 3” Item #6 With unit positioned acc ording to m easurements on previous page, pre - drill and attach a #10 x 1” sheet metal screw to hold the rear Bulkhead in place while assembling the remainder of the unit.
Begin to tighten ALL loose hardware on the remainder of the unit, being sure to align edges and bends of materials being tightened. This will square the unit to itself.
KK-XXX-05_INST_8-07 18 3/8” x 2” Hex head bolt, washers, and nut On the Rear doorframe , remove the sheet metal screws installed e arlier. Drill 3/8” holes through the doorframe, floor, and vehicle. Attach using 3/8” x 2” hex head bolts, washers, fender washers, lock washers, and hex nuts.
Socket Ball Item #14 to doors and frames Attach Ball & Socket Style Doorstop. 1 st Attach “Ball” portion of assembly. Attach to threaded hole on the doo r using a ¼” x 1” Hex head bolt. nd 2 Attach the “Socket” and brack et portion. Attach to doorframe using #8 x ¾” Phillips machine screws and keps nuts.
KK-XXX-05_INST_8-07 20 Optional Storage Compartm ent (Sold Seperatley) FINAL INSTALLATION PHOTOS Optional Storage Compartm ent (Sold Separately).
KK-XXX-05_INST_8-07 21 PT-VIDEO-X C-VS-1800-ECO w/ C-TCB-7 & C-3090-7 K K -RLL KK-PV ENT K R -CCL-1 KR-DL PRISONER TRANSPORT OPTIONS – (A ll SOLD SEPERATLEY ).
Item 3 Item 7 Item 1 Item 12 Item 5 Item 8 ITEM DESCRIPTION 1 Driver-side Bench/Wall 2 Passenger-side Bench/Wall 3 Front Bulkhead 4 Diamond-plate Floor 5 Divider 6 Rear Bulkhead/ Doorframe 7 Driver-si.
デバイスHavis-Shields Kwik-Kit KK-100-05の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Havis-Shields Kwik-Kit KK-100-05をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHavis-Shields Kwik-Kit KK-100-05の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Havis-Shields Kwik-Kit KK-100-05の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Havis-Shields Kwik-Kit KK-100-05で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Havis-Shields Kwik-Kit KK-100-05を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHavis-Shields Kwik-Kit KK-100-05の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Havis-Shields Kwik-Kit KK-100-05に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHavis-Shields Kwik-Kit KK-100-05デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
