Hayes Microcomputer ProductsメーカーMwaveの使用説明書/サービス説明書
ページ先へ移動 of 18
Linux ACP Modem (Mwave) mini−HOWTO Mike Sullivan sullivam@us.ibm.com Paul Schroeder paulsch@us.ibm.com Joy Yokley − Edited document and coverted to DocBook v4.1 (SGML). 2001−01−12 Revision History Revision .11 2002−07−18 Revised by: PBS Revision .
Table of Contents 1. General Information and Hardware Requirements ....................................................................................1 1.1. Introduction ................................................................................
1. General Information and Hardware Requirements 1.1. Introduction The ACP Modem for Linux is a software based modem. Support software for the ACP modem is composed of a loadable kernel module and a user level application.
1.6. Which Systems are Supported This version of the ACP Modem driver supports the IBM Thinkpad" 600E, 600, and 770 that include on−board ACP modem hardware. 1.7. Features of the Modem The ACP Modem provides the following features: Standard asynchronous COM port interface (NS16550A UART compatible) operation • Bell−103/212A, CCITT−V.
2. Compilation, Installation, and Startup 2.1. Prerequisites A 2.2.16 series (or later) Linux kernel source tree • An appropriate set of module utilities • gcc version 2.
Country information (including access codes) are listed in the mwavem.conf file. For example, for France the following section is present: [TelephonyCountry List33] CountryCode=00000021 Name=France SameAreaRule=0FG LongDistanceRule=0FG InternationsalRule=00EFG To set France to be your configured country in the [WORLDTRADE] section of mwavem.
The following arguments are not persistent from boot to boot (i.e. We are not saving them in the BIOS). mwave_3780i_irq=5/7/10/11/15 • This parameter allows you to configure the IRQ used by the DSP if the DSP IRQ was not set and stored in BIOS by the Thinkpad" configuration utility.
during the build process. Setup the serial driver to recognize the UART provided by the ACP driver. 2. setserial /dev/ttyS0 autoconfig NOTE Substitute /dev/ttyS0 to match the serial port you have configured the DSP to use. NOTE You may wish to create a symbolic link from your modem device to your serial device for convenience.
3. Resolving Installation and Configuration Problems The following sections list solutions to possible problems you may experience. 3.1. DSP Does Not Start In order to recognize memory above 64 Meg, it may be necessary to append the "mem=" option to the kernel command line.
IRQ 4, I/O address 0x3f8 (if using ttyS0) For dual boot systems we recommeded that you use the Thinkpad" Configuration Utility on Windows NT or DOS to configure these system resources. Windows NT Thinkpad Configuration Utility Notes: (Under the Internal Modem −−> Advanced selection) Set IRQ sharing to disabled 1.
setserial /dev/ttySx The above command should return the following for serial port 1: /dev/ttyS1, UART: 16550A, Port: 0x2f8, IRQ: 3 The port and IRQ numbers should match the information placed in the .
4. Debugging Tips 4.1. Error Logs Errors encountered by the ACP Modem device driver or application are logged using the syslog utility. 4.2. Tracing The ACP device driver supports a debug argument to enable the generation of trace information. The command for this debug is listed below.
MWMPW32_TRACE=1 MWMUTIL_TRACE=1 MWWTT32_TRACE=1 Trace information is logged using the syslog utility. Linux ACP Modem (Mwave) mini−HOWTO 4. Debugging Tips 11.
5. Test Claims This driver has been tested using the ThinkPad" 600E. The same chipset is integrated on the 600 and 770 models and should work. 5. Test Claims 12.
6. List of Supported Countries The following countries are supported by the ACP Modem driver Table 1. List of Supported Countries Country Name Country Access Code ALGERIA 213 ANTIGUA_BARBUDA 102 ARGEN.
EL_SALVADOR 503 FINLAND 358 FRANCE 33 GERMANY 49 GREECE 30 GRENADA 111 GUATEMALA 502 GUYANA 592 HONDURAS 504 HONG_KONG 852 HUNGARY 36 INDIA 91 INDONESIA 62 IRELAND 353 ISRAEL 972 ITALY 39 JAMAICA 112 .
PHILIPPINES 63 POLAND 48 PORTUGAL 351 PRC 852 ROMANIA 40 RUSSIA 7 SAUDI_ARABIA 966 SINGAPORE 65 SLOVAKIA 421 SLOVENIA 386 SOUTH_AFRICA 27 SPAIN 34 ST_KITTS_NEVIS 115 ST_LUCIA 122 ST_VINCENT 116 SURINA.
7. Trademarks Hayes is a trademark of Hayes Microcomputer Products, Inc. MNP (Microcom Network Protocol) is a trademark of Microcom, Inc. IBM is a trademark of International Business Machines, Inc.
デバイスHayes Microcomputer Products Mwaveの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hayes Microcomputer Products Mwaveをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHayes Microcomputer Products Mwaveの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hayes Microcomputer Products Mwaveの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hayes Microcomputer Products Mwaveで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hayes Microcomputer Products Mwaveを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHayes Microcomputer Products Mwaveの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hayes Microcomputer Products Mwaveに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHayes Microcomputer Products Mwaveデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
