Hayter Mowersメーカー48 PROの使用説明書/サービス説明書
ページ先へ移動 of 36
OWNER'S HANDBOOK Harrier 48 Pro CODE 486A (English V ersion) FROM SERIAL NO: 486A001001 HANDBOOK: 486046 (Rev .1.) Issue :10.05.04 486046(1) 7/7/04 12:07 pm Page 1.
1.2 MODEL CODE 486A Engine Briggs & Stratton Intek Edge 55 Engine T ype 12K682-01 16-E1 Engine / Cutterblade Speed 2800 rpm Fuel T ype Unleaded Petrol Fuel Capacity 1.5 litres Oil T ype SAE 30 engine oil Oil Sump Capacity 0.6 litres Spark Plug 491055 (Briggs & Stratton) Spark Plug Gap 0.
1ST Y ear (12 months) W e certify that this service has been carried out by an Authorised Hayter Service Dealer Date: 1ST Y ear (12 months) Owner’s Name: Serial Number: Date: 2nd Y ear (24 months) W.
486046(1) 7/7/04 12:07 pm Page 1.4.
1.18 Maintenance Schedule 1.19 - 1.25 Mower Maintenance 1.19 - Engine 1.19 - Thr ottle Cable Adjustment 1.19 - Carbur ettor Adjustments 1.20 - Oil Service 1.20 - Air Cleaner Service 1.21 - Spark Plug Service 1.21 - Keeping Engine Clean 1.21 - Grassbag 1.
Thank you for purchasing a Hayter mower . The following pages are designed to help you gain safe and efficient service from your mower . IMPOR T ANT : This ‘Owners Handbook’ should be regarded as part of the mower as it gives essential information regarding mower safety , operation, maintenance and specifications.
LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of one year from the date of purchase.
This safety alert symbol indicates important safety messages. When you see this symbol be alert to the possibility of injury . Carefully r ead the following and inform others. Y our mower is perfectly safe if used correctly . Failure to observe the following precautions may r esult in serious injury .
- Always use fresh fuel. Stale fuel can block the carburettor and cause leakage. - Replace fuel tank and oil tank caps securely . A damaged cutterblade or loose fixing bolt are major hazards. Before use, always visually inspect the cutting mechanism to ensure that it is in good condition.
Do not tilt the mower when starting the engine. Do not put hands or feet near or under rotating parts. Never pick up or carry the mower while the engine is running. Never lift the rear deflector while the engine is running. Never touch the exhaust/exhaust guard or cooling fins when the engine is hot.
Allow the engine to cool before storing in any enclosure. T o reduce the fire hazard, keep the engine and the surrounding deck area free of grass, leaves, or excessive grease. Check the rear deflector and grassbag frequently for wear or deterioration.
Adjust Handlebar Height Remove the mower from the packaging and check that the following items have been supplied correctly . If any items are missing contact, your local Hayter dealer . 1. Engine Handbook. 2. Grassbag. T o prevent accidents cut off the long ribbon attached to the grass- bag and discard.
T o prevent engine damage the engine is shipped without oil or petrol. The engine must be filled with the correct grade of oil and petrol befor e starting the engine. Always use high quality detergent oil classified “For service SE, SF , SG” SAE 30 oil.
Controls Operate all control levers several times and ensure that the cables move freely . Check that the engine stop and ground drive clutch levers return freely to their rest position when released. Whilst operating the engine throttle mechanism slight resistance should be felt when moving the lever to the ‘ choke ’ position.
Hold the handlebar and operate the ground drive clutch lever to power the mower in a forward direction. When the ground drive clutch lever is disengaged the mower may be pushed. This feature is useful when mowing in confined areas. If the engine stop lever is r eleased the engine will stop.
Move the height of cut lever sideways to disengage it from the locking notch, then push forwards to lower or pull backwards to raise the height of cut. Release the lever in the required position and ensure that it locks firmly into one of the seven notch settings.
Areas of heavy growth should be mown without collecting the clip- pings. If collection is required, first mow the area without the grass- bag at the maximum height of cut setting. Allow the grass clippings to dry out and then mow the area at the maximum height of cut setting with the grassbag fitted.
T o prevent accidents stop the engine disconnect the spark plug lead before attempting to carry out maintenance pr ocedures on the mower . Follow the hourly or calendar intervals, whichever occurs first.
Clean the engine cooling system. Clean more often under dusty conditions or when airborne debris is present or after prolonged operation whilst cutting tall, dry grass. Replace the spark plug. Check valve clearances. 1. Engine Cowl 2. Spark Plug / Lead 3.
Check the oil level daily before starting the engine and ensure that the correct oil level is maintained. Refer to-‘Before Starting the Mower ’ for oil checking and filling instructions. Change the engine oil after the first 5 hours of operation and thereafter according to the ‘Maintenance Schedule’:- 1.
Use only Briggs & Stratton spark tester (1) to check for a spark as shown in the diagram. Replace the spark plug every 100 hours or every season, whichever occurs first. A spark plug wrench is available from any authorised Briggs & Stratton service dealer .
Remove grass debris from the top and underside of the deck housing immediately after use. T o prevent damage fertilisers and top dressings are particularly corrosive. Thoroughly clean the mower deck immediately after use on treated grass and stor e well away from corrosive materials.
Lubricate the wheels, pivot points and linkages with engine oil every 25 operating hours. Apply a good quality medium grease to the inner control cables at the point of entry and exit from their outer casing. Drain the fuel by running the engine until the fuel tank is empty and the engine stops.
1 2 3 Cutterblade Assembly 1CG480V25B Assemble the cutterblade with the turned up edges facing towards the engine. Secure the cutterblade using the bolt (1), spring washer (2), and distance piece (3) and tighten to a torque of 54Nm A slightly worn cutterblade may be re-sharpened.
T o store the handlebar unscrew the 2 small securing knobs sufficient- ly to allow it to be pivoted forwards to rest against the mower . T ake care to ensure that the control cables do not become snagged at the pivot point and depress the engine stop lever to prevent it being dam- aged through contact with the engine spark plug.
PROBLEM POSSIBLE F AUL T REMEDY Engine will not turn over Engine stop lever released. Operate engine stop lever . Incorrect oil level. Check oil level. Obstruction under deck. Remove obstruction. Engine smokes Excess oil level. Check oil level. Air cleaner cartridge oil Service air cleaner .
PROBLEM POSSIBLE F AUL T REMEDY Engine vibrates excessively Mounting bolts loose. T ighten bolts Cutterblade bolt loose. T ighten bolt Cutterblade out of balance.
EC DECLARA TION OF CONFORMITY HA YTER LIMITED, Spellbrook, Bishop’ s Stortford, Herts CM23 4BU ENGLAND declare that the lawnmower: Models: Harrier 48 Pro Machine T ype No.
NO. DESCRIPTION P ART NO. QTY ITEM NOTE 1 Mainframe - Casting 486015V 1 2 Plate - Location RH 480083V 1 3 Clamp - Boss Inner 480084W 2 4 Clamp - Boss Outer 480085W 2 5 Nut - Nyloc Insert ‘T’ T ype.
NO. DESCRIPTION P ART NO. QTY ITEM NOTE 47 Ratchet HOC Moulding 480147 1 48 Throwplate - Main Body 480011 1 49 Screw - T aptite 09545 4 50 Bearing - Roller Housing 219102 2 51 Roller - Rear W/A 480210.
NO. DESCRIPTION P ART NO. QTY ITEM NOTE 93 Axle - Front W/A 219031 1 94 Moulding - Front axle Bearing 219036 2 95 Fin - Front Insert 480013 1 96 Decal - Hayter & Royal W arrant 410087 1 97 Nut - M.
11 2 11 2 11 5 98 5 2C486A01C 1 2 3 3 4 4 11 2 11 2 97 98 97 5 6 7 8 9 10 10 11 11 12 5 11 2 55 100 100 100 58 101 102 102 36 11 4 13 99 99 23 14 15 11 7 16 16 18 19 19 20 21 22 108 11 0 25 57 24 56 2.
1.33 NOTES Notes:- 486046(1) 7/7/04 12:08 pm Page 1.33.
1.34 Notes:- NOTES 486046(1) 7/7/04 12:08 pm Page 1.34.
1.35 NOTES Notes:- 486046(1) 7/7/04 12:08 pm Page 1.35.
1.36 CUST OMER INFORMA TION Serial No: Engine T ype:- 12K682-0166-E1 Engine:- Briggs & Stratton Intek Edge 55 Date of Sale:- Y our Local Dealer:- 486046(1) 7/7/04 12:08 pm Page 1.
デバイスHayter Mowers 48 PROの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hayter Mowers 48 PROをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHayter Mowers 48 PROの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hayter Mowers 48 PROの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hayter Mowers 48 PROで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hayter Mowers 48 PROを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHayter Mowers 48 PROの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hayter Mowers 48 PROに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHayter Mowers 48 PROデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
