HealthriderメーカーHRSY23080の使用説明書/サービス説明書
ページ先へ移動 of 29
¨ USERÕS MANUAL Model No. HRSY23080 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 ASSEMBLED DIMENSIONS: Height: 81 in. Width: 54 in. Length: 67 in. Low Pulley Station Foot Plate Leg Lever Butterfly Arm Press Arms Shroud Covering Weight Stack Press Arm Adjustment Cam Seat Backrest Thank you for selecting the innovative and versatile HEAL THRIDER ¨ 230 Home Gym System.
4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled ÒFRAME ASSEMBL Y . Ó Insert four 3/8Ó x 2 3/4Ó Carriage Bolts (45) up through the indicated holes in the Stabilizer (4).
4. Place the bracket on the lower end of the Main Upright (1) over the indicated 3/8Ó x 2 3/4Ó Carriage Bolts (45) in the Stabilizer (4). Hand tighten two 3/8Ó Nylon Locknuts (50) onto the Bolts.
9. Place the bracket on the lower end of the Weight Upright (2) over the indicated 3/8Ó x 2 3/4Ó Carriage Bolts (45) in the Weight Base (5). Hand tighten two 3/8Ó Nylon Locknuts (50) onto the Bolts. Do not tight- en the Nylon Locknuts yet. Locate two 3/8Ó x 1 3/4Ó Bolts (57) and slide a 3/8Ó Flat W asher (55) onto each of them.
8 12. Attach the upper ends of the Weight Guides (15) to the welded bracket underneath the Weight Upright (2) with two 3/8Ó x 1 3/4Ó Bolts (57) and two 3/8Ó Nylon Locknuts (50). Tighten, but do not overtighten, the Nylon Locknuts. 12 1 1. Slide a 3/8Ó Flat W asher (55) and a 5/8Ó x 1/2Ó Bushing (85) onto a 3/8Ó x 2 3/4Ó Bolt (47).
14. T ap two 1Ó Retainer Rings (32) and a 1Ó Round Cover Cap (81) onto one end of the Press Frame T ube (34). Lubricate the Press Frame T ube in its entire length. Note: Use the Cover Cap to tap on the Retainer Rings. Make sure the teeth on the Retainer Rings bend towards the Cover Cap (see inset drawing).
17 17. Leg Lever Assembly . Attach a Bumper (40) to the Seat Frame (7) with a #8 x 1Ó Screw (78). Press a 2Ó Square Inner Cap (28) into the indicated end of the Leg Lever (41). Lubricate a 3/8Ó x 3Ó Bolt (53). Attach the Leg Lever (41) to the Seat Frame (7) with the 3/8Ó x 3Ó Bolt and a 3/8Ó Nylon Jamnut (63).
11 23. Feed the end of the Low Cable (72) through the indi- cated slot in the Weight Upright (2) from above. Wrap the Low Cable (72) around a 3 1/2Ó Pulley (24).
12 26. Route the end of the High Cable (73) with the loop through the bracket on the Main Upright (1) from above. Route the High Cable over a 3 1/2Ó Pulley (24) in the direction shown. Slide the 3 1/2Ó Pulley (24) into the bracket on the Main Upright (1).
13 29. Wrap the High Cable (73) around a 3 1/2Ó Pulley (24) in the direction shown. Attach the 3 1/2Ó Pulley (24) to the bracket on the Stabilizer (4) with a 3/8Ó x 2Ó Bolt (54) and a 3/8Ó Nylon Locknut (50).
14 33. Wrap the High Cable (73) around a 3 1/2Ó Pulley (24) in the direction shown. Attach the 3 1/2Ó Pulley (24) and a Cable T rap (25) to the riser on the Weight Base (5) by sliding the Cable T rap and Pulley onto the 3/8Ó x 4 3/4Ó Bolt (46) attached in step 31.
15 36. Route the High Cable (73) through the slot in the leg of the Seat Frame (7). Attach the closed loop at the end of the High Cable (73) to the Leg Lever (41) with a 3/8Ó x 2 3/4Ó Bolt (47), two 3/8Ó Flat W ashers (55) and a 3/8Ó Nylon Locknut (50).
16 40 21 19 17 89 48 68 40. Important: Follow all three Cables from end to end and make sure they rest in the grooves of all Pulleys and that both the Cables and the Pulleys move smoothly .
17 44. Press two 3/4Ó Round Inner Caps (43) into each Pad T ube (42). Insert one Pad T ube (42) into the Seat Frame (7). Slide a Foam Roller (30) onto each end of the Pad T ube. Insert the other Pad T ube (42) into the Leg Lever (41). Slide a Foam Roller (30) onto each end of the Pad T ube.
18 48 48. The decal shown below has been attached to the home gym system in the location shown. If the decal is missing or illegible, please call our customer hotline at the number on the front cover to order a replacement decal. Apply the new decal in the appropriate location.
19 Cable Diagram The Cable Diagrams below show the proper routing of the Butterfly Cable (92), the High Cable (73) and the Low Cable (72). The numbers show the correct route for each Cable. Make sure the Cables are routed correctly , that the Pulleys move smoothly and that the Cable T raps do not touch or bind the Cables.
20 Attaching the Lat Bar , Ankle Strap or Ab Strap to the High Pulley Station Attach the Lat Bar (61) to the High Cable (73) with a Cable Clip (69). For some exercises, the Chain (67) should be attached between the Lat Bar and the High Cable with two Cable Clips.
Coordinating the Positions of the Backrest and Press Frame For many exercises, the Press Frame (8) and the Backrest (12) must be in the correct positions relative to each other . The Press Frame can be set in 12 dif ferent positions, as indicated by the decal on the cam of the Press Arm Adjustment Frame (see drawing A).
22 Adjusting the Butterfly Arms Make sure the Backrest (12) is in the horizontal position as described on the previous page. Pull out the Adjustment Knob (66) on one of the Adjustment Discs (26, 27) and pivot the Butterfly Arm (10 or 1 1) up or down to the desired position.
23 Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the Cables before resistance is felt, the Cables should be tightened. Slack can be removed by moving one or both of the 3 1/2Ó Pulleys (24) attached to the Adjustable Pulley Frame (23).
3/4" Round Inner Cap (43) 3/4Ó Dome Cap (82) 5/8Ó x 1/2Ó Bushing (85) 1/2Ó x 3/4Ó Bushing (76) 1/2Ó x 3/8Ó Bushing (83) 5/8Ó x 1Ó Bushing (86) 5/8Ó x 1 1/4Ó Bushing (91) 1/2Ó x 1 13/1.
3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63) 1/4" x 1 1/2" Bolt (95) 5/16" Nylon Locknut (64) #8 x 1Ó Screw (78) 3/8" x 1 1/2" Button Head Screw (52) 1/4" Fl.
3/8" x 3 1/2" Bolt (56) 3/8" x 4 3/4" Bolt (46) 3/8" x 2 3/4" Bolt (47) 3/8" x 2 3/4" Carriage Bolt (45) 3/8" x 2" Bolt (54) 3/8" x 1 3/4" B.
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 Main Upright 2 1 Weight Upright 3 1 Support Upright 4 1 Stabilizer 5 1 Weight Base 6 1 Seat Base .
30 43 90 49 49 40 78 53 41 73 30 43 28 50 47 42 43 30 28 63 42 43 30 90 13 50 7 6 45 56 50 25 50 24 47 50 50 38 39 50 37 101 65 65 12 55 53 91 24 25 63 44 14 44 8 32 34 9 55 55 46 46 55 32 24 55 47 85.
Ordering Replacement Parts Limited W arranty T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
デバイスHealthrider HRSY23080の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Healthrider HRSY23080をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHealthrider HRSY23080の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Healthrider HRSY23080の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Healthrider HRSY23080で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Healthrider HRSY23080を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHealthrider HRSY23080の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Healthrider HRSY23080に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHealthrider HRSY23080デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。