HealthriderメーカーHRSY54370の使用説明書/サービス説明書
ページ先へ移動 of 20
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory .
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool- ing down.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 90 in. (Extended) Width: 48 in. Length: 59 in. The HealthRider ¨ BRS requires a minimum ceiling height of 7 1/2 feet.
5 ASSEMBL Y 1 60 60 Before beginning assembly , carefully read the following information and instructions: ¥ Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.
2. Press four 2Ó Square Inner Caps (68) into the Frame (2). Identify the Left Wheel Channel (3) and the Right Wheel Channel (4) by comparing the welded brackets on the bottom of each Wheel Channel. Slide the Left Wheel Channel (3) onto the indicated Small Wheels (40) attached to the Frame (2).
4. Slide the Support T ube (32) onto the Base (1). Attach the Support T ube to the Base with two 3/8Ó x 2Ó Bolts (43) and two 3/8Ó Nylon Locknuts (39). Do not tighten the Nylon Locknuts yet. 5. Attach the Support T ube (32) to the Right Wheel Channel (4) with two 3/8Ó x 1Ó Bolts (16) and two 3/8Ó Nylon Locknuts (39).
7. Lubricate the 1/2Ó x 3 1/2Ó Carriage Bolt (49). Attach the Lift T ube (1 1) to the Frame (2) with the Carriage Bolt and a 1/2Ó Nylon Jam Nut (50). 8. Attach the Platform Cover (34) and the Crossbar (18) to the Frame (2) with two 3/8Ó x 2 3/4Ó Bolts (45) and two 3/8Ó Nylon Locknuts (39).
1 1. Press a 1Ó Round Inner Cap (36) into one of the Press Arms (6). Press a 1 3/4Ó Square Inner Cap (65) into the Press Arm. Repeat this step for the other Press Arm (6). 12. Identify the Right Butterfly Arm (15) and the Left Butterfly Arm (14). Note the position of the welded bracket on each Arm.
14. Cut the plastic zip tie (not shown) from the Cable (35). Be careful not to damage the Cable. Pull on the Cable (35) until you have enough slack to route the Cable around the Pulley (41) attached to the Right Butterfly Arm (15). T ighten the 3/8Ó x 2Ó Bolt (43).
18. Insert a 1/4Ó x 2 1/2Ó Carriage Bolt (57) through the center hole in a Seat Plate (29). Attach the Seat Plate to the Seat (23) with two 1/4Ó x 3/4Ó Bolts (56). Attach another Seat Plate (29) to the Seat (23) in the same manner . Insert the 1/4Ó x 2 1/2Ó Carriage Bolts (57) through the holes in the Seat Frame (13).
12 ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise guide accompanying this manual to see how the home gym system should be set up for each exercise.
13 A TT ACHING THE LA T BAR, ROW BAR, OR NYLON STRAP T O THE LOW PULLEY ST A TION Attach the Lat Bar (21) to the Cable (35) with a Cable Clip (38). For some exercises, the Chain (37) should be attached between the Lat Bar and the Cable with two Cable Clips.
14 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent.
15 CABLE DIAGRAM The cable diagram below shows the proper routing of the Cable (35). Use this diagram to be sure that the Cable has been assembled correctly . The starting and ending points have been labeled. The numbers show the proper route for the Cable.
3/8" Nylon Locknut (39) 3/8" W asher (46) 1/2" x 3 1/2" Carriage Bolt (49) 1/2" Nylon Jam Nut (50) 3/8" x 2 1/2" Bolt (51) 1/4" Nylon Locknut (54) 1/4" W a.
3/8" x 1" Bolt (16) 3/8" x 2" Bolt (43) 3/4" T ap Screw (62) 1" Square Inner Cap (64) 1 3/4" Square Inner Cap (65) 2" Square Inner Cap (68) 3/4" Round Oute.
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. P ART LISTÑModel No. HRSY54370 R1 197A Key No. Qty .
31 30 30 30 30 21 23 28 29 29 27 13 26 25 26 27 27 12 26 25 26 27 38 37 41 5 6 30 24 24 15 14 20 41 41 7 22 8 2 18 9 10 40 19 17 42 42 11 33 9 41 1 42 42 32 3 4 41 41 41 41 41 41 40 40 30 40 57 57 56 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
デバイスHealthrider HRSY54370の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Healthrider HRSY54370をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHealthrider HRSY54370の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Healthrider HRSY54370の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Healthrider HRSY54370で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Healthrider HRSY54370を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHealthrider HRSY54370の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Healthrider HRSY54370に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHealthrider HRSY54370デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。