Hearth and Home TechnologiesメーカーBE-36-Cの使用説明書/サービス説明書
ページ先へ移動 of 37
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas • Do not try to light any appliance.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 3 TABLE OF CONTENTS Safety and W arning Information ................................................ 2 Service Parts Lists ...........................................
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 5 (NG , LP) Service Parts List / Liste des pièces de rechange IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 6 (NG , LP) Exploded Part s Diagram (GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturing Date: .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 7 BE-36-C (NG , LP) Exploded Part s Diagram (GN, PL) Vue éclatée des pièces Service Parts Beginning Manufacturin.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 8 Appliance Certification The fireplace model discussed in this Installers Guide has been tested to certification standards and listed by the applicable laboratories.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 9 2 Getting St arted Introducing the Hearth & Home T echnologies G as Fireplaces Hearth & Home T echnologie.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 10 Figure 1. Diagram of model BE-36-C HOOD VENT COL LA R S RA TING PLA TES & LABE LS BOTT OM GRILLE COVER ELEC .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 11 3 Inst alling the Fireplace Step 1. Locating the Fireplace The following diagram shows space and clearance require- ments for locating a fireplace within a room. Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 12 Figure 3. Framing Dimensions for SL D-Series and DVP-Series Pipe A B C D* E * 3 7 ” 3 3 ” 16 1/4” 36 1/2” 24 3/8 Framing should be constructed of 2 X 4 lumber or heavier .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 13 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 4 .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 14 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 5 .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 15 Step 3. Inst alling the V ent System A. V ent System Approvals This model has vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attach the vent system.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 16 STRAIGHT UP VERTICAL VENTING V (FT .) 45' MAX. Figure 8. Straight up V ertical V enting Use SL D-Series component s only . NOTE: For vertical venting over 20 feet an Extended V ertical Baffle Kit is recommended for improved flame appearance.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 17 Figure 1 1. V enting with One 90° Elbow V (MIN.) H (MAX.) 90 o Elbow on T op 2.5' (863mm) 1' (305mm) 3 ' (914mm) 2' (610mm) 4' (1.22m) 3' (914mm) 6' (1.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 18 V H H + H 1 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 19 Figure 13. V enting with T wo 90° Elbows BE-36-C V (MIN.) H + H 1 (MAX.) 90 o Elbow on T op 2.5' (863mm) 1' (305mm) 3' (914mm) 2' (610mm) 4' (1.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 20 Figure 14. V enting with Three 90° elbows 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 21 Use SL D-Series components only . BE-36-C H + H 1 (MAX.) 4' (1.22m) 6' (1.86m) 8' (2.48m) 12' (3.72m) 16' (4.8m) 16' (4.8m) Figure 15.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 22 Figure 16. V enting with Four 90° elbows VENTING WITH FOUR (4) 90° ELBOWS NA TURAL AND PROP ANE GAS V (MIN.) H (MAX.) 2' (609mm) 5' (1.52m) V 1 (MIN.) H 1 (MAX.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 23 B. Installing V ent Components After determining which set of starting collars will be used (top or rear), follow venting instructions accordingly .
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 24 For V ertical Runs - The vent system must be supported every eight (8) feet (2.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 25 For V ertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 26 C. V ent T ermination SL-Series V enting Only: For Horizont al T erminations - T o attach and secure the termina.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 27 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 26. V ent T ermination Minimum Clearances A = 12" ......................
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 28 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 29 ! Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fireplace into position. • Level the fireplace from side to side and from front to back.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 30 Figure 30. Gas Supply Line Step 6. The Gas Supply Line NOTE: Have the gas supply line installed by a qualified service technician in accordance with all building codes.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 31 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 32 Figure 32. Remote Wiring Diagram (IPI) Figure 33. Remote Wiring Diagram (Standing Pilot) ORANGE GREEN V AL VE OR.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 33 Figure 35. Fan Wiring Diagram FAN TEMP ERA TURE SEN SOR SW I TCH SPEED CONTROL (RHEOST A T) JUNC TIO N BOX Figure 34. Intermittent Pilot Ignition (IPI) Wiring Diagram NOTE 1: Ignition module, valve, pilot and wall switch operate on 3 volts.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 34 Step 9. Finishing Figure 36 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 35 Placing the Ember Material Ember material is shipped with this gas fireplace. The bag labeled Glowing Ember (050-721) is standard glowing ember material. T o place the ember material: • Remove the top louver by lifting it up and away from the unit.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 36 Step 1 1. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace.
Hearth & Home T echnologies • BE-36-C, BE-36-CIPI • 397-981 Rev . R • 2/05 37 4 Maint aining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fireplace serv.
デバイスHearth and Home Technologies BE-36-Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hearth and Home Technologies BE-36-Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHearth and Home Technologies BE-36-Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hearth and Home Technologies BE-36-Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hearth and Home Technologies BE-36-Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hearth and Home Technologies BE-36-Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHearth and Home Technologies BE-36-Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hearth and Home Technologies BE-36-Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHearth and Home Technologies BE-36-Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
