Heat & Glo LifeStyleメーカーSL-750TRS-IPI-Dの使用説明書/サービス説明書
ページ先へ移動 of 45
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 1 Models: SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Owner ’ s Manual Installation and Operation • Do not store or use gasoline or other flamma- ble vapors and liquids in the vicinity of this or any other appliance.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 2 These units MUST use one of the vent systems described in the Installing the Appliance section of the Installers Guide . NO OTHER vent systems or component s MA Y BE USED .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 3 TABLE OF CONTENTS Safety and Warning Information ......................................................... 2 Service Parts Lists ......................................
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 4 (NG , LP) Exploded Parts Diagram Service Parts SL-350TRS-C Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ Part number list on following page.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 5 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 6 (NG , LP) Exploded Parts Diagram Service Parts Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 7 (NG , LP) Exploded Parts Diagram Service Parts SL-550TRS-IPI-D Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______ 7 Log Set Assembly Part number list on following page.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 8 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 9 (NG , LP) Exploded Parts Diagram Service Parts SL-750TRS-IPI-D Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______ Part number list on following page.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 10 (NG , LP) Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 11 (NG , LP) Exploded Parts Diagram Service Parts Beginning Manufacturing Date: 4-04 Ending Manufacturing Date: ______.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 12 1 Approvals and Codes Heat & Glo Quality Systems registered by SGS ICS Appliance Certification The Heat & Glo appliance models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 13 For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 14 2 Getting St arted Introducing the Heat & Glo Gas Appliances Heat & Glo direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 15 Figure 1. Diagram of the SL-750TRS-IPI-D HOOD GAS CONTROLS GAS LINE ACCESS VENT COLLARS TOP S T ANDOFFS ELECTRICAL ACCESS RA TING PLA TES & LABELS BO TT OM GR IL L E COVER CERA MIC FIBE R P A D 37-7 /8 962 [] 3-9/ 16 90 [] 6-7/8 175 [] 35-5/ 8 905 [] 41 1041.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 16 Figure 2. Diagram of the SL-550TRS-IPI-D 32-9/16 827 [] 3-1 /2 90 [ ] 6- 7/8 174 [] 36 914 [] 31- 1/8 791 [ ] 32-1/8 816 [ ] 5- 1/2 140 [ ] 2-1/ 8 54 [ ] 6 152 [] 35-7/16 900.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 17 Figure 3. Diagram of the SL-350TRS-C 6-7 / 8 17 4 [] 3-1 / 2 90 [] 30- 5/8 77 7 [] 21-1/4 54 0 [] 29 737 [] 15-1/4 .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 18 3 Inst alling the Appliance Step 1. Locating the Appliance S pace and clearance requirements for locating a appliance within a room (see Figure 4).
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 19 Figure 5. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavier . The framing headers may rest on the appliance stand-offs. Step 2. Framing the Appliance Appliance framing can be built before or after the appliance is set in place.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 20 NOTE: PIPES OVERLAP 1-1/4 INCHES (34.93mm) A T EACH JOINT . Figure 6.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 21 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) A T EACH JOINT . Figure 7 .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 22 ! Figure 8. V ent System Component s and T ermination Kits Step 3. Inst alling the V ent System A. V ent System Approvals These models have vent starting collars on both the top and the back of the unit.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 23 90-DEGR EE EL BOW S Figure 9. Flex V ent The flex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 24 V H 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX. (1.22m) 3' MIN. (914mm) 6' MAX. (1.86m) 4' MIN. (1.22m) 8' MAX. (2.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 25 V H H + H 1 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 26 Figure 15. V enting with T wo 90° Elbows Use SL D-Series component s only . VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + H + H 1 MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 27 Figure 16. Venting with T wo 90° Elbows Use SL D-Series components only . H V V 1 VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H MAX. = 16 FT (4.8m) V + V 1 + H MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 28 Figure 17. V enting with Three 90° elbows 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 29 Figure 18. V enting with three 90° elbows Use SL D-Series components only . VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS VENTING WITH THREE (3) 90 o ELBOWS PROP ANE V + H + V 1 + H 1 MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 30 Use SL D-Series components only . Figure 19. V enting with three 90° elbows V 1 H 1 H V VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + V 1 + H + H 1 MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 31 Figure 20. V enting with Four 90° elbows VENTING WITH FOUR (4) 90° ELBOWS NA TURAL AND PROP ANE GAS V (MIN.) H (MAX.) 2' (609mm) 5' (1.52m) V 1 (MIN.) H 1 (MAX.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 32 ! Figure 21. Insert screwdriver or similar object here to remove cap.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 33 For V ertical Runs - The vent system must be supported every eight (8) feet (2.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 34 For V ertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes. T o install firestop s for vertical runs that pass through ceilings: • Position a plumb bob directly over the center of the verti- cal vent component.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 35 C. V ent T ermination SL-Series V enting Only: For Horizont al T erminations - T o attach and secure the terminatio.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 36 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 30. V ent T ermination Minimum Clearances A = 1 2" ....................... clearances above grade, veran- da, porch, deck or balcony B = 1 2" .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 37 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 38 Step 4. Positioning, Leveling, and Securing the Appliance • Place the appliance into position. • Level the appliance from side to side and from front to back. • Shim the appliance with non-combustible material, such as sheet metal, as necessary .
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 39 • Insert insulation from the outside of the appliance and pack the insulation tightly to totally seal between the pipe and the outer casing.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 40 Step 8. W iring the Appliance NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 41 Figure 36. Intermittent Pilot Ignition (IPI) Wiring Diagram TRANSFORMER 3 V AC PLUG IN R E D BA T TER Y P ACK THE R.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 42 Step 9. Finishing Figure 38 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 43 Inst alling the T rim Combustible materials may be brought up to the specified clearances on the side and top front edges of the appliance, but MUST NEVER overlap onto the front face.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 44 Step 1 1. Before Lighting the Appliance Before lighting the appliance, be sure to do the following: Remove all paperwork from underneath the appliance.
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev . J • 5/06 45 4 Maint aining and Servicing Y our Appliance Appliance Maintenance Although the frequency of your appliance servici.
デバイスHeat & Glo LifeStyle SL-750TRS-IPI-Dの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Heat & Glo LifeStyle SL-750TRS-IPI-Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHeat & Glo LifeStyle SL-750TRS-IPI-Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Heat & Glo LifeStyle SL-750TRS-IPI-Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Heat & Glo LifeStyle SL-750TRS-IPI-Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Heat & Glo LifeStyle SL-750TRS-IPI-Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHeat & Glo LifeStyle SL-750TRS-IPI-Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Heat & Glo LifeStyle SL-750TRS-IPI-Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHeat & Glo LifeStyle SL-750TRS-IPI-Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
