Heat & Glo LifeStyleメーカーSUPREME-XTSの使用説明書/サービス説明書
ページ先へ移動 of 40
1 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Model(s): Supreme-XTS Grand-XTS • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/inst.
3 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. BTU Speci fi cations . . . . . . . . .
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 4 Note : T o assure top performance, safety and ef fi ciency , inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions.
5 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Heat & Glo gas inserts are designed for recessed installa- tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 6 T OP VIEW A C B 3 3 F ireplace Size Requirements Figure 3.1 Fireplace Opening Minimum Appliance Size Location Grand-XTS Suprem.
7 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 B. Clearances Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Fire Risk. • Locate and install appliance to all clearance speci fi cations in manual. Fire Risk.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 8 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.
9 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 CAUTION ALL vent speci fi cations MUST be followed. • This product is tested and listed to these speci fi cations. • Appliance performance will suffer if speci fi cations are not followed.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s speci fi cation.
11 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 A. V enting Components 7 7 Installing V ent P ipe and Appliance The vertical vent termination system installed on this model includes: • One length of 3-inch fl exible vent pipe for combustion air (included with vent kit).
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 12 Figure 7.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 7.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top.
13 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 D. Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.2) . T o install adaptor see Figure 7.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 14 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve.
15 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 16 A. Wiring the Appliance 9 9 Elect rical Infor mation Note : This appliance must be electrically wired and grounded in accorda.
17 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 B. Junction Box Installation Figure 9.2 Junction box installation JUNCTION BOX SIDEW ALL JUNCTION BOX ACCESS SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower or remote.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 18 Figure 9.4 Fan/Rheostat Wire Diagram NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 0 C RA TED WIRE.
19 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 20 Figure 1 1.1 Placement of Embers 1 1 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox.
21 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Log Set Assembly: LOGS-SXT E. Positioning the Logs CAUTION: Logs are fragile! Carefully remove the logs from the packaging. If the gas logs have been factory installed they should not need to be positioned.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 22 LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner . The slot on the right side of log #3 fi ts over the bar grate. LOG #2 (SRV349-702): Position log #2 by locating its slot over the tab on the front left of the burner .
23 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 LOG #6 (SRV349-706): Position the "Y" end of log #6 into the cutout on log #4 and its opposite end into the groove on log #2. LOG #5 (SRV327-705): Rest log #5 in the cutouts on both log #1 and log #3 as shown.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 24 Log Set Assembly: LOGS-GXT 2 2 3 3 6 6 5 5 4 4 1 1 Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 339-935 2/02 LOG #1 (SRV339-701): Place log #1 in the back on the insert.
25 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 LOG #3 (SRV327-703): Position log #3 by locating its slot over the tab on the right front of the burner .
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 26 LOG #6 (SRV327-705): Rest log #6 in the smooth area just to the left of the knothole in log #1 and on log #3. The front edge of log #1 should be at the top of the hole when looking through the hole in log #6.
27 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Figure 1 1.5 Glass Assembly F . Glass Assembly G. Air Shutter Setting Optimal fl ame appearance is dependent on the air shutter setting. Adjustments should be made by a qualified technician.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 28 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition.
29 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 B. Lighting Appliance Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 30 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1.
31 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 E. Frequently Asked Questions Fire Risk. High T emperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air . • Do NOT place combustible items on top of or in front of appliance.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 32 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
33 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 34 1 4 14 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season.
35 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary .
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 36 Figure 15.1 Appliance Dimensions 1 5 15 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Fo r framing dimensions and clearances refer to Section 3.
37 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 15.2) LINK-DV -30B or (LINK-DV -30) : Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter .
43 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 D. Limited Lifetime W arranty.
Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 44.
45 Heat & Glo • Supreme-XTS, Grand-XTS • 349-901 Rev . i • 12/09 E. Contact Information - NOTES - ________________________________________________________________________________ ___________.
デバイスHeat & Glo LifeStyle SUPREME-XTSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Heat & Glo LifeStyle SUPREME-XTSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHeat & Glo LifeStyle SUPREME-XTSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Heat & Glo LifeStyle SUPREME-XTSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Heat & Glo LifeStyle SUPREME-XTSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Heat & Glo LifeStyle SUPREME-XTSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHeat & Glo LifeStyle SUPREME-XTSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Heat & Glo LifeStyle SUPREME-XTSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHeat & Glo LifeStyle SUPREME-XTSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
