Henny PennyメーカーOFE- 290の使用説明書/サービス説明書
ページ先へ移動 of 18
Model OFE- 290 3-1. OPERA TING COMPONENTS POWER/PUMP Switch A three way switch with center OFF position; move the switch to the position marked POWER to operate the fryer; move the switch to the posit.
Model OFE- 290 3-1. OPERA TING COMPONENTS (Continued) High Limit This high temperature control senses the temperature of the shortening; if the temperature of the shortening exceeds 450°F (230°C), t.
Model OFE- 290 3-4. SWITCHES AND Refer to image at end of this section. INDICA T ORS Product Selection Buttons Select the number of heads, or product, to be cooked by pressing the button below the men.
Model OFE- 290 EXIT COOL Button After cooking, or filtering the shortening, the temperature automati- cally goes into the Cool Mode, which keeps shortening at a lower temperature; this temperature ext.
Model OFE- 290 3-5. FILLING OR ADDING SHOR TENING The shortening level must always be above the heating elements when the fryer is heating and at the frypot level indicators on the r ear of the frypot (Figur e 3-3). Failur e to follow these instructions could r esult in a fir e and/or damage to the fryer .
Model OFE- 290 3-6. BASIC OPERA TION Follow the procedure below on the initial start-up of the fryer , and each time the fryer is brought from a cold, or shut down condition, back into operation. These are basic, general instructions. Be sure to follow KFC’ s Standards Library when operating the fryer .
Model OFE- 290 3-6. BASIC OPERA TION 4. Allow fryer to heat until digital display shows “DROP”. (Continued) (Press the EXIT COOL button if the display shows COOL”) The heat cycles on and off approximately 10 degrees before the setpoint temperature, to help prevent overshooting the setpoint temperature.
Model OFE- 290 3-7. CARE OF THE SHOR TENING FOLLOW THE INSTRUCTIONS BELOW T O A VOID SHOR TENING OVERFLOWING THE FR YPOT , WHICH COULD RESUL T IN SERIOUS BURNS, PERSONAL INJURY , FIRE, AND/OR PROPERTY DAMAGE. 1. T o protect the shortening when the fryer is not in immediate use, the fryer should be put into the Cool Mode.
Model OFE- 290 3-8. FIL TERING INSTRUCTIONS (continued) ONL Y FIL TER WHEN “COOL” IS DISPLA YED. FAILURE T O DO SO CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT , CAUSING SERIOUS BURNS, PERSONAL INJUR Y , FIRE,AND/OR PROPER TY DAMAGE .
Model OFE- 290 3-8. FIL TERING 5. Scrape cracklings and crackling ring from frypot and discard. INSTRUCTIONS Do not let cracklings drain into filter drain pan. These crack- (Continued) lings can cause a burned taste in gravy . W ipe all surfaces with a clean damp towel.
Model OFE- 290 3-10. CLEANING THE FR YPOT After the initial installation of the fryer , as well as before every change of shortening, the frypot should be thoroughly cleaned as follows: 1 . T urn the POWER/PUMP switch to OFF positioin, and unplug unit from wall receptacle.
Model OFE- 290 3-1 1. FIL TER PUMP MOT OR The filter pump motor is equipped with a manual reset button, PROTECTOR-MANUAL located on the rear of the motor , in case the motor overheats. If RESET motor won’t run, wait about 5 minutes before attempting to reset this protective device to allow motor to cool.
Model OFE- 290 3-14. PROGRAMMING 1. Press and hold the FUNCTION button for two seconds. “REG PROGRAM” shows in the display , followed by “CODE”.
Model OFE- 290 7. After the load compensation, press and release the FUNC- TION button. “PROP” and “CONTROL” shows on the left side of the display and the factory preset proportional control temperature shows on the right side of the display .
Model OFE- 290 3-14. PROGRAMMING (continued) 13 . After the end-of-cycle point is set, press and release the FUNCTION button. “HEAD” flashes on the left side of the display and a number shows on the right side of the display .
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) Factory Presets (F/C, Gas/Electric, Speaker V olume, Speaker Fr equency , Codes, Initialize System) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display .
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) T ech I/O Mode 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 4 times until “TECH I-O” shows in the display .
Model OFE- 290 3-16. SPECIAL PROGRAM Heat Control MODE (Continued) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 6 times until “HEA T CNTRL” shows in the display .
デバイスHenny Penny OFE- 290の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Henny Penny OFE- 290をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHenny Penny OFE- 290の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Henny Penny OFE- 290の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Henny Penny OFE- 290で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Henny Penny OFE- 290を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHenny Penny OFE- 290の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Henny Penny OFE- 290に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHenny Penny OFE- 290デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
