Hitachiメーカー232437の使用説明書/サービス説明書
ページ先へ移動 of 20
Instructions – Parts List GRACO INC. P .O. BOX 1441 MINNEAPOLIS, MN 55440–1441 Copyright 1999, Graco Inc. is registered to I.S. EN ISO 9001 Pail Mount Airless Packages 308765F Model 232437 Shown 8109C 0359 II 1/2 G T3 ITS03A TEX1 1251 Important Safety Instructions Read all warnings and instructions in this manual.
2 308765 T able of Contents List of Models 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W arnings 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup 6 . . . . . . . . . . . . . . . . . . . . . .
308765 3 Symbols W arning Symbol W ARNING This symbol alerts you to the possibility of serious injury or death if you do not follow the instructions. Caution Symbol CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.
4 308765 W ARNING SKIN INJECTION HAZARD Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury .
308765 5 W ARNING FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury . D Ground the equipment and the object being sprayed. Refer to Grounding on page 7.
6 308765 Setup General Information NOTE: Reference numbers and letters in parentheses in the text refer to the callouts in the figures and the parts drawing. NOTE: Always use Genuine Graco Parts and Acces- sories, available from your Graco distributor .
308765 7 Setup Grounding W ARNING FIRE AND EXPLOSION HAZARD Before operating the pump, ground the system as explained below . Also read the section FIRE AND EXPLOSION HAZARD on page 5. 1. Pump: use the ground wire and clamp (supplied). See Fig. 1. Loosen the grounding lug locknut (W) and washer (X).
8 308765 Setup Supplied Components Refer to Fig. 2. W ARNING A red-handled bleed-type master air valve (E) and a fluid drain valve (F) are supplied. These compo- nents help reduce the risk of serious .
308765 9 Setup 8108C KEY SUPPLIED COMPONENTS 1 5 Gallon (19 liter) Pail Cover 2 Pump 13 Fluid Filter (includes fluid drain valve F) 15 Air Relief V a lve 18 Pump Ground Wire (required; see page 7 for .
10 308765 Operation Pressure Relief Procedure W ARNING SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally . Fluid under high pressure can be injected through the skin and cause serious injury .
308765 1 1 Operation Prime the Pump 1. See Fig. 3. Remove the tip guard and spray tip from the gun (106). Refer to the gun manual. 2. Close the pump air regulator (G), and bleed-type air valves (B, E). 3. Connect the air line (A) to the air inlet swivel (H).
12 308765 Operation Adjust the Spray Pattern 1. Start the pump. Use the pump air regulator (G) to adjust the pump speed and fluid pressure until the spray is completely atomized. Use the lowest pressure necessary to get the desired results. Higher pressure may not improve the spray pattern and will cause premature tip and pump wear .
308765 13 Operation Fig. 3 KEY 1 5 Gallon (19 liter) Pail Cover 2 Pump 13 Fluid Filter (includes fluid drain valve F) 19 5 Gallon (19 liter) Pail 20 Screw Knobs 39 Agitator 41 Agitator Air Supply T ub.
14 308765 Maintenance Preventive Maintenance Schedule The operating conditions of your particular system determine how often maintenance is required. Estab- lish a preventive maintenance schedule by recording when and what kind of maintenance is needed, and then determine a regular schedule for checking your system.
308765 15 Parts Part No. 232433, Series A, 23:1 Monark, cst, without agitator , with hose and gun Part No. 232434, Series A, 23:1 Monark, cst, without agitator , hose, and gun Part No. 232437, Series A, 23:1 Monark, cst, with agitator , hose, and gun (shown) Part No.
16 308765 Parts Part No. 232433, Series A, 23:1 Monark, cst, without agitator , with hose and gun Part No. 232434, Series A, 23:1 Monark, cst, without agitator , hose, and gun Part No. 232437, Series A, 23:1 Monark, cst, with agitator , hose, and gun (shown) Part No.
308765 17 Parts Part No. 232437, Series A, 23:1 Monark, carbon steel (shown) 8107B 13 18 5 14 12 1 8 3 11 4 2 101 102 103 104 106 6 7 7 (Ref) 9 10 15 16 17 17 (Ref) 19 20 21 22 23, 25 24 30 31 39 40 4.
18 308765 T echnical Data Category Data Maximum fluid working pressure 2300 psi (16 MPa, 160 bar) Maximum air input pressure 100 psi (0.7 MPa, 7 bar) Ratio 23:1 Maximum operating temperature 120 _ F (.
308765 19 Dimensions 81 10A B A Model 232437 Shown (hose and gun not shown) A (height) B (diameter of pail) Weight 32 in. (813 mm) 10.625 in. (270 mm) 47 lb (21 kg).
20 308765 Graco Standard W arranty Graco w arrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
デバイスHitachi 232437の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hitachi 232437をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi 232437の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi 232437の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi 232437で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi 232437を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi 232437の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi 232437に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi 232437デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。