HitachiメーカーC 18DBLの使用説明書/サービス説明書
ページ先へ移動 of 16
Cordless Circular Saw Model C 18DBL Handling instructions Note: Before using this Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool.
1 GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
2 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs.
3 Lower guard function a) Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent.
4 Fig. 2 29. Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK. NEVER place your hand or fingers behind the saw ( Fig. 3 ). If kickback occurs, the saw could easily jump backwards over your hand, possibly causing severe injury.
5 1. Make sure that swarf and dust do not collect on the battery. 䡬 During work make sure that swarf and dust do not fall on the battery. 䡬 Make sure that any swarf and dust falling on the power tool during work do not collect on the battery. 䡬 Do not store an unused battery in a location exposed to swarf and dust.
6 APPLICATION Cutting various types of wood. BATTERY REMOVAL/INSTALLATION 1. Battery removal Hold the handle tightly and push the battery latches to remove the battery (see Fig. 9, 10 ). CAUTION Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (see Fig.
7 CHARGING Before using the power tool, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle. When the power cord is connected, the charger’s pilot lamp will blink in red. (At 1-second intervals) CAUTION Do not use the electrical cord if damaged.
8 NOTE The charging time may vary according to temperature and power source voltage. CAUTION When the battery charger has been continuously used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.
9 Fig. 14 Fig. 15 NOTE Values of the inclined gauge provided on the base merely serve as a rough guideline. For cutting operation at an inclined posture, use the circular saw after adjusting the angle between the base and the saw blade with a protractor, etc.
10 Loosen the fixed M4 screw on the guide piece, should the fixing position be wrong, and make necessary adjustment of the position. Fig. 20 HOW TO USE 1. Operation of switch (Fig. 21) (switch trigger and light switch) (1) For safe operation of the machine, a “switch lock” is provided on the side of a handle.
11 If the base is slanted (45 degrees), use the small front scale as the guide ( Fig. 15 , Fig. 24 ). Fig. 23 Fig. 24 (2) Ensure that the switch is turned to the ON position before the saw blade comes in contact with the lumber. The switch is turned ON when the trigger is squeezed; and OFF when the trigger is released.
12 Fig. 27 MAINTENANCE AND INSPECTION CAUTION Pull out battery before doing any inspection or maintenance. 1. Inspecting the saw blade Since use of a dull saw blade will degrade efficiency and cause possible motor malfunction, sharpen or replace the saw blade as soon as abrasion is noted.
13 Important notice on the batteries for the Hitachi cordless power tools Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless powe.
14 A C B A B C 501 502 503 504 505 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 29 30 31 32 33 34 37 30 38 39 35 40 41 42 36 43 44 43 26 27 28 45 46 47 48 49 52 50 55 56 57 58 54 53 60 61 62 59 65 63 66 67 68 59 69 70 71 72 73 64 59 74 10 53 64 66 71 75 51 Item Part Name Q’TY No.
403 Code No. C99212912 G Printed in China Hitachi Koki Co., Lt d. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan 02Back_C18DBL_ENG 4/1/14, 9:14 15.
デバイスHitachi C 18DBLの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hitachi C 18DBLをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHitachi C 18DBLの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hitachi C 18DBLの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hitachi C 18DBLで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hitachi C 18DBLを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHitachi C 18DBLの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hitachi C 18DBLに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHitachi C 18DBLデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
