HobartメーカーAM14C ML-32615の使用説明書/サービス説明書
ページ先へ移動 of 20
MODEL AM14 & AM14C DISHWASHERS MODELS AM14 ML-32614 AM14C ML-32615 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34123 Rev.
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of MODEL AM14 & AM14C DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14 dishwashers are semi-automatic rack-type machines. On model AM14, the doors open on opposite sides of the machine allowing the rack to move straight through.
– 5 – Available as an optional accessory is a frame-mounted 10KW electric booster to maintain a minimum final rinse temperature of 180 ° F. Also available as an optional accessory is the model IB57 Infrared Booster Gas Water Heater. Also available are circuit breaker(s) and/or single point electrical connection options.
– 6 – WATER REQUIREMENTS Proper water quality can improve ware washing performance by reducing spotting, lowering chemical supply costs, enhancing effectiveness of labor, and extending equipment life. Local water conditions vary from one location to another.
– 7 – With Electric Booster Water Heater The water supply line is connected to the booster (Fig. 6) with 3 / 4 " pipe. The water supply should have a minimum temperature of 120 ° F – 140 ° F, and a flowing pressure of 15 – 25 psig at the pressure gauge tee beside the solenoid valve.
– 8 – The dishwasher must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearances for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of make-up air in the room to allow for combustion of the gas at the burner(s).
– 9 – RATE OF EXHAUST FLOW CALCULATIONS Based on the 1996 International Mechanical Code. The Rate of air flow required for a vent hood is calculated using the following definitions: Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood.
– 10 – STEAM HEAT (When Specified) A 3 / 4 " union connection for the steam supply line is located at the lower right side of the machine. The steam supply must have a flowing pressure of 15 – 20 psig. Steam flow is controlled by a solenoid valve, as well as a mechanical ball valve.
– 11 – Electric Booster Water Heater Option NOTE : Electric Booster electrical connection will be separate from the dishwasher electrical connection unless single point electrical connection is supplied. If circuit breaker option is provided, the electric supply or supplies are connected to the circuit breaker box on top of the dishwasher.
– 12 – A T A D L A C I R T C E L EA T A D L A C I R T C E L E A T A D L A C I R T C E L E A T A D L A C I R T C E L EA T A D L A C I R T C E L E l e d o Ml e d o M l e d o M l e d o Ml e d o Mh P .
– 13 – OPERA TION PREPARATION Place the pump strainer (when equipped), overflow tube, overflow cover, end cover, slanted strainer, and the strainer bucket in their respective positions, (Fig. 7). Fig. 7 An automatic detergent dispenser is recommended.
– 14 – PL-40416-1 Reset Button Rinse T emperature Adjustment Screw DISHWASHING Scrape the dishes to remove large particles of food and debris. Never use steel wool on ware to be loaded into the dishmachine. Fig. 9 Stack the dishes in a rack. Do not stack dishes one on top of another as water must have free access to all sides of every dish.
– 15 – CLEANING T he machine must b e thoroughly cleaned at the end of each working shift or at least daily. Never use steel wool to clean warewasher surfaces. Use only products formulated to be safe on stainless steel. Turn off the power switch. If the machine has steam heat, close the manually operated steam ( ball) valve.
– 16 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness (4 – 6 grains per gallon is recommended). DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave doors open).
– 17 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. WASH ARMS Upper and lower wash and rinse arms (Figs.
– 18 – To avoid a service call, check symptoms and related possible causes. If machine still does not operate properly, contact Service. SYMPTOM POSSIBLE CAUSE No machine operation. 1. Blown fuse or tripped circuit breaker at power supply. 2. Machine control is in MANUAL mode.
– 19 – SYMPTOM POSSIBLE CAUSE Inadequate rinse. 1. Dirty line strainer causing reduced water flow. Turn off water supply, remove strainer cap, withdraw and clean screen. Reassemble. 2. Low supply line pressure. 3. Excessive mineral deposits throughout wash and rinse system.
– 20 – SERVICE Contact your local Hobart-authorized service office for any repairs or adjustments needed on this equipment. If a gas orifice fitting is to be adjusted or replaced, have it serviced by qualified Hobart- authorized service personnel.
デバイスHobart AM14C ML-32615の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hobart AM14C ML-32615をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart AM14C ML-32615の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart AM14C ML-32615の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart AM14C ML-32615で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart AM14C ML-32615を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart AM14C ML-32615の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart AM14C ML-32615に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart AM14C ML-32615デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。