HobartメーカーAM14TCの使用説明書/サービス説明書
ページ先へ移動 of 20
MODEL AM14F , AM14T , & AM14TC DISHW ASHERS MODELS AM14F ML-110975 AM14T ML-110973 AM14TC ML-110974 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of MODEL AM14F , AM14T , AM14TC DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14T, AM14TC, and AM14F dishwashers are semi-automatic rack-type machines. On model AM14T (Fig. 1) the doors open on opposite sides of the machine allowing the rack to move straight through.
– 5 – DO NOT attempt to operate this dishwasher in the chemical sanitizing mode without a properly installed, NSF-listed, chemical sanitizer feeder (not supplied with machine). Contact an authorized detergent representative for information about a chemical sanitizer feeder.
– 6 – On models AM14T and AM14TC, dish tables should be turned down and fitted into the dishwasher (Fig. 2). Use an NSF approved sealer between table and tank lip to prevent leakage. Fasten the tables to the tank lip with truss head screws. Dish tables are not required with model AM14F.
– 7 – WATER CONNECTION A suitable water hammer arrestor should be installed in the water line just ahead of the dishwasher. Without Electric or Gas Booster Water Heater The water supply line is connected to the line strainer (Fig. 1) with 3 / 4 " pipe.
– 8 – Static inlet gas pressure should not exceed 14" W.C. for either natural or propane gas. The minimum value is for purpose of input adjustment. The gas valve (Fig. 3) is provided with a pressure tap to measure the gas pressure downstream, which is also the manifold pressure.
– 9 – VENTING REQUIREMENTS — WITH GAS TANK HEAT The Hobart AM14F / AM14T / AM14TC dishwasher equipped for gas tank heat is not provided with a flue collar and is not intended to have the flue directly connected to a ventilation system. However, the products of combustion must be vented to the outside air.
– 10 – The Rate of air flow required for a vent hood is calculated using the following definitions (Fig. 6): Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood. A = Area of Hood Opening = (L x W) in Feet 2 D = Clearance Height = Distance in Feet from lower lip of hood to top of dishwasher chamber.
– 11 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 12 – OPTIONAL EQUIPMENT CONNECTIONS — Vent Fan and Gas Booster WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 13 – DETERGENT, RINSE AID, OR SANITIZER DISPENSERS — Tubing Installation All detergent, rinse aid, and / or sanitizer dispensers must have all connections sealed against leakage.
– 14 – OPTIONAL EQUIPMENT CONNECTIONS — Detergent, Rinse Aid, Sanitizer Dispensers WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 15 – Fig. 13 PO W ER O N / O F F FILL CYCLE WASH 1 2 4 6 Power Switch Cycle Switch Wash / Fill Switch PL-52759 Fig. 11 PL-41 178-1 MANUAL / AUTO SWITCH W ASH / RINSE SWITCH POWER SWITCH READOUT .
– 16 – Models AM14T / AM14TC In Automatic mode, the M ANUAL / A UTO switch (Fig. 12) is on A UTOMATIC and the W ASH / R INSE switch is O FF . The wash and rinse cycles begin automatically. The wash cycle begins when the machine doors are closed. The rinse cycle begins when the wash cycle is completed.
– 17 – PL-40468-1 AM14T Shown Rinse Nozzle Knurled Disk Rinse Arm Wash Arm PL-40809-1 AM14T Shown Rinse Nozzle Rinse arm W ash arm Knurled Disk – Unscrew and support both arms on release. CLEANING T he machine m ust b e thoroughly cleaned at the end of each working shift or at least daily.
– 18 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. Wash Arms Upper and lower wash and rinse arms (Figs.
– 19 – TROUBLESHOOTING Manual Reset Button on Pump Motor The motor is equipped with a gray manual reset button near the end cover of the motor. If the pump motor becomes overheated, the thermal overload protector will cause the motor to not operate.
– 20 – FORM 34555 ( Dec. 2000 ) PRINTED IN U.S.A. SYMPTOM POSSIBLE CAUSE Inadequate rinse or rinse water 1. Dirty line strainer causing reduced water flow. Turn off water supply, temperature is too low. remove strainer cap, withdraw and clean screen.
デバイスHobart AM14TCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart AM14TCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart AM14TCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart AM14TCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart AM14TCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart AM14TCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart AM14TCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart AM14TCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart AM14TCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
