HobartメーカーD Seriesの使用説明書/サービス説明書
ページ先へ移動 of 12
I N S T R U C T I O N S FORM 18261 Rev. E (Jan. 2002) D SERIES REACH-IN REFRIGERA T ORS & FREEZERS D SERIES REACH-INS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
–2– © HOBART CORPORATION, 1991 D Series Reach-In Refrigerators & Freezers INST ALLA TION UNPACKING Immediately after unpacking the reach-in, check for possible shipping damage. If this unit is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.
–3– ASSEMBLY Some components can be removed to allow the cabinet to pass through short or narrow doorways. The door handle can be removed as follows: 1. If the adhesive-backed trim pieces are damaged during removal, new ones can be purchased from Hobart.
– 4 – LEGS OR CASTERS WARNING : THE CABINET MUST BE BLOCKED AND STABLE BEFORE INSTALLING LEGS OR CASTERS. Legs (Fig. 4) To install the legs, raise and block the reach-in a minimum of 7" from the floor and thread the legs into the threaded holes on the bottom of the cabinet.
– 5 – Condensate Evaporator D Series units are equipped with an automatic condensate evaporator that requires no drain connection. ELECTRICAL CONNECTIONS (Cord Connected Reach-Ins) 120Volt, 60 Hertz, 1 Phase WARNING : THIS MACHINE IS PROVIDED WITH A THREE-PRONGED GROUNDING PLUG.
– 6 – ELECTR ONIC DEFROST TIMER (when equipped) If your freezer is equipped with an electronic Defrost Timer, it is located in a control box behind the trim rail at the top of the Reach-In Freezer. To access the the Defrost Timer, remove the Thumbscrew on the left side of the Control Box and slide the Lid to the left (Fig.
– 7 – To Change the Defrost Duration and Bypass the Setting of the Time Clock Begin with the SET CLOCK light blinking rapidly, indicating normal Operation Mode . . . If you want to change the Defrost Duration but not reset the time-of-day, press and hold the PROGRAM button for about 3 seconds until the PROGRAM light starts blinking.
– 8 – How to Set a Custom Defrost Schedule Begin with the defrost timer on normal Operation Mode: The SET CLOCK light is blinking rapidly and the PROGRAM and DEFROST ON lights are off. If all switches are OFF (Fig. 12), the factory preset defrost schedule is enabled: 2 AM , 8 AM , 2 PM , 8 PM .
– 9 – Program Review During normal Operation Mode, with the SET CLOCK light blinking rapidly . . . Press the SET button until the SET CLOCK, PROGRAM and DEFROST ON lights are lit; then release the SET button and all three lights go off for two seconds.
– 10 – If the Defrost Timer's Battery Loses Power If the SET CLOCK, PROGRAM and DEFR OST ON lights are all blinking (Fig. 15), the backup po wer supply (batter y) to the Defrost Timer has weak ened.
– 11 – Fig. 16 DEFROST TIMER — Freezer units built between 1991 and 1997 were equipped with a defrost timer (Fig. 16) preset for four 23 – 25 minute defrost cycles per day (every 6 hours). By inserting a screwdriver into the large hole in the bracket and turning clockwise, the time of day that these cycles occur may be adjusted.
– 12 – FORM 18261 Rev. E (Jan. 2002) PRINTED IN U.S.A. MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquid dishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit, abrasive materials, bleach or harsh chemicals.
デバイスHobart D Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart D Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart D Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart D Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart D Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart D Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart D Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart D Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart D Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
