HobartメーカーFT900 SERIESの使用説明書/サービス説明書
ページ先へ移動 of 16
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 33906 Rev. C (Mar. 2000) FT900 SERIES DISHW ASHERS R-L OPERATION L-R OPERATION LOAD 5' ML-110672 ML-110673 6' M.
– 2 – Operation and Care of FT900 SERIES DISHW ASHERS SA VE THESE INSTRUCTIONS OPERA TION MACHINE PREPARATION — Check before beginning operation. Raise the machine doors and make sure all components are in their proper operating positions. Pump Intake Screens must be put on holders at each pump intake (Fig.
– 3 – FILL Assure proper water hardness. Recommended range is 4 – 6 grains per gallon. All water (and steam, if equipped) supply valves must be opened and the electric supply turned on before the machine will function. Close the drains and doors.
– 4 – Empty Strainer Baskets During Operation as Necessary The Strainer Baskets must be emptied periodically during operation to prevent them from becoming clogged, which would adversely affect dishwasher operation. STOP the machine and open the side access doors; Strainer Baskets are immediately inside at the front of the tanks.
– 5 – CLEANING The dishwasher MUST be thoroughly cleaned at the end of each working shift. Drain the machine by lowering the drain levers to a horizontal position. Drain levers are located near the floor at the front of each tank. Draining the tanks requires approximately 5 – 10 minutes.
– 6 – When tanks are empty, remove pump intake screens (Fig. 21) and clean them in a sink. Remove the final rinse arms (Fig. 22). Clean debris from nozzles and arms using a straightened paper clip (Fig. 23). Never use steel wool to clean warewasher surfaces.
– 7 – CLEANING THE TOP DUCT WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT THE MACHINE IS BEING WORKED ON BEFORE YOU BEGIN CLEANING. Debris and airborne particles will settle on the Top Covers and the surfaces inside the Top Duct.
– 8 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness of 4 to 6 grains per gallon. DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave doors open).
– 9 – HANG CURTAINS Curtains must be in their proper places (Fig. 30) . . . A Short Curtain on the unload side of each upper Wash Arm, Long Curtains on both sides of every section divider, Two Long Cur tains at the Load End.
– 10 – C O N T R O L B O X PREWASH ARM o o ooooo TWO SHORT CURTAINS AT UNLOAD SIDE OF UPPER ARMS THREE PAIRS OF LONG CURTAINS AT SECTION DIVIDERS LOAD UNLOAD WASH ARM FT900S R - L OPERATION WITH 4' CENTER SECTION RINSE ARM Fig.
– 11 – Fig. 30 FOUR SHORT CURTAINS AT UNLOAD SIDE OF UPPER ARMS AND BETWEEN TWO RINSE ARMS FT900W R - L OPERATION WITH 11' CENTER SECTION C O N T R O L B O X PREWASH ARM o o ooooo ooooo FIVE .
– 12 – PL-41059-1 REMOVE PLUG TO CHECK OIL LEVEL CONVEYOR MOTOR GEAR CASE PL-41060-1 DRAIN PLUG MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT BEFORE PERFORMING ANY MAINTENANCE PROCEDURE.
– 13 – PL-41061-1 RESET BUTT ON Conveyor Speed Adjustment The conveyor speed can be adjusted by your local Hobart service technician. For Model FT900 and FT900W, maximum speed is 12 feet-per-minute, FPM , (factory preset is 8 – 9 FPM ). For Model FT900S, maximum speed is 6.
– 14 – Fig. 35 Rinse Actuator SYMPTOM POSSIBLE CAUSE Leaking Valve (Except Solenoid Type) Supplied by Others 1. 2. Foreign material preventing proper valve operation. A critical period is soon after installation when pipe compound or metal shavings may lodge at the valve seat.
– 15 – SYMPTOM POSSIBLE CAUSE Continuous Rinse Operation (on machines equipped with Photoelectric Sensor Rinse, Figs. 27, 36.) 1. 2. 4. Photoelectric sensors are blocked. Clean sensor openings (Fig. 27). Remove side panels from load end of machine adjacent to pre-wash chamber.
– 16 – FORM 33906 Rev. C (Mar. 2000) PRINTED IN U.S.A. DATE ______________________ DAY / SHIFT TIME PREWASH TANK TEMPERATURE WASH TANK TEMPERATURE POWER RINSE TANK TEMPERATURE FINAL RINSE TEMPERAT.
デバイスHobart FT900 SERIESの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart FT900 SERIESをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart FT900 SERIESの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart FT900 SERIESの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart FT900 SERIESで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart FT900 SERIESを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart FT900 SERIESの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart FT900 SERIESに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart FT900 SERIESデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
