HobartメーカーQ Seriesの使用説明書/サービス説明書
ページ先へ移動 of 12
FORM 14580 Rev. L (Jan. 2002) N S T R U C T I O N S I 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com Q SERIES REACH-IN FOOD ST ORA GE CABINETS Q SERIES REACH-IN.
– 2 – Installation, Operation and Care of Q SERIES REA CH-IN FOOD ST ORA GE CABINETS SA VE THESE INSTR UCTIONS GENERAL The Q Series Reach-In Food Storage Cabinets are available as low temperature (0°F), medium temperature (38°F) refrigeration units or hot food storage cabinets (180°F maximum).
– 3 – ASSEMBLY Some components can be removed to allow the cabinet to pass through short or narrow doorways. The door handle can be removed as follows: 1. Remove the screw and bolt from the tumbler. 2. Remove the two mounting screws and the handle assembly (Fig.
– 4 – LEGS OR CASTERS WARNING : THE CABINET MUST BE BLOCKED AND STABLE BEFORE INSTALLING LEGS OR CASTERS. Legs (Fig. 5) To install the legs, raise and block the reach-in a minimum of 7 " from the floor and thread the legs into the Threaded Holes on the bottom of the cabinet.
– 5 – Compressor Mounts Some Q Series units have the compressor specially mounted to help prevent damage during shipment. If the compressor is mounted on shipping blocks, remove the shipping blocks before operating the compressor. If the compressor is mounted on springs, refer to the tag attached to the compressor.
– 6 – STANDARD THERMOMETER (Fig. 9) — The standard digital thermometer is calibrated at the factory and does not permit recalibration. OPTIONAL DIAL THERMOMETER — The optional dial thermometer can be recalibrated. Compare the cabinet thermometer with an accurate test thermometer.
– 7 – ELECTR ONIC DEFROST TIMER (when equipped) If your freezer is equipped with an electronic Defrost Timer, it is located in a control box behind the trim rail at the top of the Reach-In Freezer. To access the the Defrost Timer, remove the Thumbscrew on the left side of the Control Box and slide the Lid to the left (Fig.
– 8 – To Change the Defrost Duration and Bypass the Setting of the Time Clock Begin with the SET CLOCK light blinking rapidly, indicating normal Operation Mode . . . If you want to change the Defrost Duration but not reset the time-of-day, press and hold the PROGRAM button for about 3 seconds until the PROGRAM light starts blinking.
– 9 – How to Set a Custom Defrost Schedule Begin with the defrost timer on normal Operation Mode: The SET CLOCK light is blinking rapidly and the PROGRAM and DEFROST ON lights are off. If all switches are OFF (Fig. 15), the factory preset defrost schedule is enabled: 2 AM , 8 AM , 2 PM , 8 PM .
– 10 – Program Review During normal Operation Mode, with the SET CLOCK light blinking rapidly . . . Press the SET button until the SET CLOCK, PROGRAM, and DEFROST ON lights are lit; then release the SET button and all three lights go off for two seconds.
– 11 – If the Defrost Timer's Battery Loses Power If the SET CLOCK, PR OGRAM and DEFROST ON lights are all b linking, the backup po wer supply (batter y) to the Defrost Timer has weakened. Estimated batter y lif e is 10 years. The timer can continue to function normally after the batter y has weak ened if the timer is reprogrammed.
– 12 – FORM 14580 Rev. L (Jan. 2002) PRINTED IN U.S.A. MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquid dishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit, abrasive materials, bleach or harsh chemicals.
デバイスHobart Q Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart Q Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart Q Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart Q Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart Q Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart Q Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart Q Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart Q Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart Q Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
