Hobart Welding ProductsメーカーOM-227 978Bの使用説明書/サービス説明書
ページ先へ移動 of 52
Processes OM-227 978B 2007−04 Handler 210 Arc W elding Power Source And Wire Feeder Description MIG (GMAW ) W elding Flux Cored (FCA W ) W elding R.
Hobart W elders manufactures a full line of welders and welding related equipment. For information on other quality Hobart products, contact your local Hobart distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-877-Hobart1 or visit our website at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ABLE OF CONTENTS SECTION 9 − MIG WELDING (GMA W) GUIDELINES 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1. T ypical MIG Process Connections 30 . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-227 978 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.
OM-227 978 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.
OM-227 978 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-227 978 Page 4 1-5. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www .
OM-227 978 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION fre_som _3/05 Y A vertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-227 978 Page 6 Le rayonnement de l’arc du procédé de soudage génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provo- quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage.
OM-227 978 Page 7 2-3 . Dangers s upplémenta ires en r elation ave c l ’installa tion, l e f onctionnement et l a maintenanc e Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur , au-dessus ou à proximité de surfaces inflammables.
OM-227 978 Page 8 2-5. Prin cipales nor mes d e sécu rité Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www .
OM-227 978 Page 9 SECTION 3 − DEFINITIONS 3-1. Symbols And Definitions A Amperage V V oltage Hz Hertz Negative Positive Direct Current (DC) Single Phase Input Output V oltage Input Of f On Do Not Switch While W elding Gas Metal Arc W elding (GMA W) Wire Feed Flux Cored Arc W elding (FCA W) SECTION 4 − SPECIFICA TIONS 4-1.
OM-227 978 Page 10 4-2. Duty Cycle And Overheating Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, thermostat(s) opens, output stops, and cooling fan runs. W ait fifteen minutes for unit to cool.
OM-227 978 Page 1 1 SECTION 5 − INST ALLA TION 5-1. Installing Welding Gun 804 686-A 1 Drive Assembly 2 MIG Gun 3 Gun Securing Thumbscrew 4 Gun End Loosen thumbscrew . Insert end through opening until it bottoms against drive assembly . Tighten thumbscrew .
OM-227 978 Page 12 5-3. Process/Polarity T able Process Polarity Cable Connections Process Polarity Cable T o Gun Cable T o Work GMAW − Solid wire with shield- ing gas DCEP − Reverse polarity Conn.
OM-227 978 Page 13 5-5. Installing Gas Supply Obtain gas cylinder and chain to running gear , wall, or other stationary support so cylinder cannot fall and break of f valve. 1 Cap 2 Cylinder V alve Remove c ap, stand to side of valve, and open valve slightly .
OM-227 978 Page 14 5-6. Selecting A Location And Connecting Input Power Y Special installation may be required where gasoline or volatile liquids are present − see NEC Article 51 1 or CEC Section 20. Y Installation must meet all Na- tional and Local Codes − have only qualified persons make this installation.
OM-227 978 Page 15 5-7. Electrical Service Guide Input V oltage 230 Input Amperes At Rated Output 24 Max Recommended Standard Fuse Or Circuit Breaker Rating In Amperes Circuit Breaker 1 , Time-Delay 2.
OM-227 978 Page 16 5-9. Installing Contact Tip And Nozzle T ools Needed: Ref. 802 399-A Y T urn off welding power source. 1 Nozzle Remove nozzle. 2 Contact T ip 3 T ip Adapter Thread welding wire through gun (see Section 5-1 1). Slide contact tip over wire and tighten tip into tip adapter .
OM-227 978 Page 17 5-10. Connecting Optional Spool Gun 804 695-A / 804 696-A 1 Drive Assembly 2 Spool Gun 3 Gun Securing Thumbscrew 4 Gun End Loosen thumbscrew . Insert end through opening until it bottoms against drive assembly . Tighten thumbscrew .
OM-227 978 Page 18 5-1 1. Threading Welding Wire 1 Wire Spool 2 W elding Wire 3 Inlet Wire Guide 4 Pressure Adjustment Knob 5 Drive Roll 6 Gun Conduit Cable Lay gun cable out straight. T ools Needed: Pull and hold wire; cut off end. Remove gun nozzle and contact tip.
OM-227 978 Page 19 SECTION 6 − O P E R A T I O N 6-1. Controls 1 Wire Speed Control Us e control to select a wire feed speed. As V oltage switch setting increases, wire speed range also increases (see weld setting label in welding power source or Section 6-2 , as applicable).
OM-227 978 Page 20 6-2. W eld Parameter Chart For 230 V AC Model /.
OM-227 978 Page 21 227 949-B B.
OM-227 978 Page 22 SECTION 7 − MAINTENANCE &TROUBLESHOOTING 7-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more often during severe conditions.
OM-227 978 Page 23 7-4. Changing Drive Roll Or Wire Inlet Guide 1 Inlet Wi r e G u i d e S e c u r i n g Screw 2 Inlet Wire Guide Loosen screw . Slide tip as close to drive rolls as possible without touching.
OM-227 978 Page 24 7-6. Cleaning Or Replacing Gun Liner Ref. 804 692-A 8 mm / 10mm Y Disconnect gun from unit. T ools Needed: T o Reassemble Gun: Insert new liner . Install wire outlet guide so that 1/8 in (3 mm) of liner sticks out. Hand tighten outlet guide, and then tighten two full turns more.
OM-227 978 Page 25 7-7. Replacing Switch And/Or Head T ube Ref. ST-800 795-C T ools Nee d e d : 19 mm Remove handle locking nut. Slide handle. Secure head tube in vice. Loosen jam nut. Remove from vice an d turn head tube out by hand. Hand-tighten head tube into cable connector .
OM-227 978 Page 26 7-8. T roubleshooting T able T rouble Remedy No weld output; wire does not feed; fan does not run. Secure power cord plug in receptacle (see Section 5-6). does not run. Replace building line fuse or reset circuit breaker if open. Place Power switch in On position (see Section 6-1).
OM-227 978 Page 27 Notes.
OM-227 978 Page 28 SECTION 8 − ELECTRICAL DIAGRAM Figure 8-1. Circuit Diagram.
OM-227 978 Page 29 227 951-B.
OM-227 978 Page 30 SECTION 9 − MIG WELDING (GMA W) GUIDELINES 9-1. T ypical MIG Process Connections Y W eld current can damage electronic parts in vehicles. Disconnect both battery cables before welding on a vehicle. Pla c e w o r k c l a m p a s close t o the weld as possible.
OM-227 978 Page 31 9-2. T ypical MIG Process Control Settings These settings are guidelines only . Material and wire type, joint design, fitup, position, shielding gas, etc. affect settings. T est welds to be sure they comply to specifications. NOTE 3.
OM-227 978 Page 32 9-3. Holding And Positioning Welding Gun Welding wire is energized when gun trigger is pressed. Before lowering helmet and pressing trigger , be sure wire is no more than 1/2 in (13 mm) past end of nozzle, and tip of wire is positioned correctly on seam.
OM-227 978 Page 33 9-4. Conditions That Affect Weld Bead Shape Weld bead shape depends on gun angle, direction of travel, electrode extension (stickout), travel speed, thickness of base metal, wire feed speed (weld current), and voltage.
OM-227 978 Page 34 9-5. Gun Movement During Welding Normally , a single stringer bead is satisfactory for most narrow groove weld joints; however , for wide groove weld joints or bridging across gaps, a weave bead or multiple stringer beads works better .
OM-227 978 Page 35 9-8. T roubleshooting − Excessive Spatter Excessive Spa tter − scattering of molten metal partic les that cool t o solid form near weld bead. S-0636 Possible Causes Corrective Actions Wire feed speed too high. Select lower wire feed speed.
OM-227 978 Page 36 9-1 1. T roubleshooting − Lack Of Penetration Lack Of Penetration − shallow fusion between weld metal and base metal. Lack of Penetration Good Penetration S-0638 Possible Causes Corrective Actions Improper joint preparation. Material too thick.
OM-227 978 Page 37 9-14. T roubleshooting − W aviness Of Bead W aviness O f Bead − weld metal that is not parallel and does not cover joint formed by base metal. S-0641 Possible Causes Corrective Actions W elding wire extends too far out of nozzle.
OM-227 978 Page 38 9-17. T roubleshooting Guide For Semiautomatic Welding Equipment Problem Probable Cause Remedy Wire feed motor operates, bu t wire does not feed. T oo little pressure on wire feed rolls. Increase pressure setting on wire feed rolls.
OM-227 978 Page 39 Notes.
OM-227 978 Page 40 SECTION 10 − P ARTS LIST . Hardware is common and not available unless listed. 804 691-A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 34 32 31 49 43 48 47 46 45 44 51 50 36 35 42 41 40 38 39 37 30 33 52 53 54 56 55 57 58 Figure 10-1.
OM-227 978 Page 41 Description Part No. Dia. Mkgs. Item No. Figure 10-1. Main Assembly Quanti ty 1 199 566 DOOR, access 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-227 978 Page 42 Description Part No. Dia. Mkgs. Item No. Figure 10-1. Main Assembly (Continued) Quanti ty 40 196 574 SWITCH, rocker DPST 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-227 978 Page 43 804 692-A 1 2 34 5 6 7 9 8 10 11 12 Figure 10-2. H-14 Gun Quanti ty Description Part No. 231 204 Item No. Figure 10-2. H-14 Gun 1 NOZZLE, slip type .500 orf flush (see Section 10-5) . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-227 978 Page 44 10-3. Optional Drive Rolls For All Feed Head Assemblies P ART NO. WIRE DIAMETER INCHES (mm) 202 925 .023/.025 (.6) and .030/.035 (.8 and .9) 202 926 .030/.035 (.8 and .9) and .045 (1.2 VK Groove) 10-4. Options P ART NO. DESCRIPTION REMARKS 770 187 Running Gear/Cylinder Rack For One Small Gas Cylinder , 100 lb (45 kg) max.
Notes.
Notes W o r k l i ke a P r o ! Pros wel d and cut safel y . Read the safety rules at the beginning of this manual ..
Warranty Questions? Call 1-800-332-3281 7 AM − 6 PM EST hobart_warr 2007−01 Service Y o u always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281.
PRINTED IN USA © 2007 Hobart Welding Products. 2007−01 Hoba rt We lding Product s An I l li noi s T ool Works Company 600 W es t Main Street Troy , OH 45373 U SA For T echn i cal A ssistance: Call1.
デバイスHobart Welding Products OM-227 978Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobart Welding Products OM-227 978Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobart Welding Products OM-227 978Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobart Welding Products OM-227 978Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobart Welding Products OM-227 978Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobart Welding Products OM-227 978Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobart Welding Products OM-227 978Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobart Welding Products OM-227 978Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobart Welding Products OM-227 978Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
