Hobieメーカー12の使用説明書/サービス説明書
ページ先へ移動 of 14
I, ': 1_(, 1 , - !." I!_' : ';..' HOLDER@ 12 - ASSEMBI~~ = '~ :" ' ".
A ;. - Introduction Welcome to the Holder@ family of sailors. Thanks for joining us. By purchasing the Holder@ 12, you are treating yourself to the ultimate in sailing enjoyment. Even if you have long experience with sailboats, please read this manual thoroughly.
HOLDER 12@ Terminology ~ .. MAST WINDOW OUTHAUL REAR PIN DDWNHAUL BOOM VANG BECKET BLOCK BOOM BLOCKS VANG LINE TILLER EXTEN TRAVELE MAIN SHEET VANG ADJUSTER CLEAT HULL DAGGERBOARD . '£ WARNING Before starting assembly, be sure the area in i which you plan to work is free from overhead power lines.
1) Hull 12) Sail 26) Warranty Card, Manual 2) Pad Eye with Block 13) Battens 27) Tiller Extension 3) Mast Tube 14) Daggerboard 28) Hull Drain Plug 4) Jam Cleat 15) Rudder Assembly 29) Cockpit Drain Hole ! 5) Upper Mast Comptip@ 16) Mainsheet (5/16" x 35) 30) Gudgeons ~,~ 6) Lower Mast 17) Halyard Line (1/4" x 34) 31) Hiking Straps ~.
ASSEMBLY INSTRUCTIONS I. The Plugs II. Traveler Assembly The larger drain plug (part #25) is used to Figure 3 shows an example of a completed drain the cockpit of the boat. Insert the large traveler line and block assembly. To assemble t drain plug from the inside of the HOLDER@ 12 the traveler, first find the traveler block set.
III. Mast and Sail Assembly A. Standard and Special Edition The mast is in two sections (part #'s 5, 6). The bottom section displays the warnings against sailing and assembling near overhead t wires and power lines. Before raising the mast, check again that you are in a safe area and always remember this warning.
(Figure 9). Place the sail in the cockpit and connect the zipper by wrapping the luff sleeve around the mast. Fold the webbing around to th~.velcro@~tt~chmeD.tp()int (Figure 10). t. . Fig. 9 Fig. 10 Make sure the halyard is on the inside of the luff sleeve.
IV. Boom Assembly V. Outhaul, Downhaul and . . Vang Assembly The HOLDER@ 12 boom (part #9) IS sImple to use, yet it is one of the most advanced designs Locate the outhaul line (part #18) and the available on a sailboat of this size. To connect downhaul line (part #20).
VI. Mainsheet Assembly Locate mainsheet (part #16). Take one end of the mainsheet and tie it to the small block hanging at the rear of the boom with a bowline (Figure 18). Run the free end through the large r block of the traveler block set and then back up to and through the .
VII. Rudder and DaggerboardSpecial Notes To attach the rudder assembly (part #15) to Using the Kick-up Rudder the boat, align the pins on the rudder with the The kick-up rudder on the HOLDER@ 12 fittings (~art ~30) on the transom. Make sure permits the rudder to do all of the hard work by - t~at the tiller IS placed ~nderneath the tr~ve.
VIII. Basic Sailing: Righting the Boat . . '. If you tip over, stay with the boat (it won't Safe a!1d sane guldehne.s for the begInner, an sink and is easy to right).) It's not necessary, easy review for the experIenced. but the boat is easier to right when the mast is .
IX. Trailering B. Appearance In addition to following all the instructions It's very easy to keep your new HOLDER@ 12 included with your trailer and obeying the rele- fresh-looking. Just follow these minor steps. vant state laws concerning trailering boats, several safety tips should be included in your 1.
Knots to Use .. ., FIGURE 8 * KNOT AT END OF LINE DDUBLE HITCH KNOT FIGURE 8 KNOT BOWLINE KNOT HALYARO KNOT 1. 2. ""' ~ ~ 1~--- -"" r :::-- :.:A4 I ~/ T CLEATING OFF A LINE Basic Sailing THIS AREA CANNOT BE SAILED ~ Iff Q ~ ~ t't()~~ WIND l<~~ V () ?j WIND [ ~ Cia "'ift' ~~«.
Remember Watch for overhead wires whenever you are sailing, launching, or trailering with the mast up. The mast sticks up there a long way and shock or death could result if it comes in contact with overhead wires. So look up when moving the boat around or even stePPing the mast, and give any wires a wide berth.
デバイスHobie 12の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hobie 12をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobie 12の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobie 12の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobie 12で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobie 12を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobie 12の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobie 12に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobie 12デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。