Hobieメーカー18 SEの使用説明書/サービス説明書
ページ先へ移動 of 34
.
WELCOME T O THE HOBIE W A Y OF LIFE Congratulations on the purchase of your new HOBIE 18’ and welcome to the HOBIE® sailing family. The HOBIE 18 cannot be outgrown. A single adult can sail it at top performance - and a crew of four can cruise in comfort.
1 This assembly manual takes you step- by-step through the setting-up and sailing of your new HOBIE 18. This manual will help you understand each part in det ail. Note that this manual applies for both Hobie 18 SE and SX models. Setting up your HOBIE 18 P AGE Packaging Layout .
2 Packaging Layout 1. Port Hull 2. Starboard Hull 3. Back Bar 4. Boom 5. Tiller Cross Bar 6. Front Bar 7. Battens 8. Rigkit Box #1 9. Rigkit Box # 2 10. Rudders 11. Daggerboards 12. Sail Main and Jib 13. Trampoline 14. Mast (not shown) Hobie Cat 18 SE Rig Kit Box #1 (fig 2) Description Quantity 1.
3 Framing the Hulls (Recommend two people) Tools- HEX wrench (provided) and a screwdriver with a 1 /4" head. Retaining Channel 8 Front Bar Inboard Bolt 3 3/4" 2 Front Bar Outboard Bolt 2" 2 Rear Cross Bar Inboard Bolt 2 1/ 2" 2 Rear Cross Bar Outboard Bolt 2" 2 Lock Nuts for 802-359 Outboard Bolts 4 1.
11. Install all four outboard bolts in the manner described in step 10. To insert the bolts in the front corner castings it will be necessary to remove the cover plates. Be careful when extracting the cover plate retaining screw. It is made of aluminum and can be galled.
Figure 9 Figure 8 5.
6 5. Insert the aft outboard corner of the trampoline into the extrusion on the inside of the hull and pull the trampoline as far aft as it will go. 6. Repeat steps 2-5 for installing the starboard trampoline. 7. In front of the rear cross bar there is a hole in either inboard rail.
7 MAST ASSEMBL Y 1. Support mast at both ends on saw horses or other such devices. Ref: Illus. #1, Pg. 20. 2. Spreaders. In the rig kit you will find all the parts of the spreader assembly. 3. The larger of the two pairs of aluminum rods (1-1), is the spreader arm.
8 19. Slip the port diamond wire into the tip of the port spreader arm. Make sure that the anti-chafing roller on the diamond wire is above the spreader tip. Secure the diamond wire by installing one of the long cotter pins (1- 8) through the tip of the spreader.
STEPPING THE MAST . DANGER - Do not attempt to step the mast in an area of low overhead wires. A mast contacting an electrical wire could be fatal. 1. Secure the four trapeze wires near the bottom of the mast so that they will be out of the way while the mast is being raised.
4. With the hinge in place over the step insert the mast step pin through the entire assembly so that it is visible on the opposite side on the hinge. 5. Attach the bridle wires to the bow tangs. Attach the roller furler mechanism between the bridle wires.
13. Lace it through the rope lock and then through the thimble at the end of the trapeze wire. Now tie the line onto either end of the dogbone. See Figure 23. 14. Repeat this process for the other three trapeze wires at the respective locations. BOOM INST ALLA TION 1.
Hobie 18 and SX18 UPDA TES INSTALLING THE RUDDER ASSEMBLY The rudders were updated after 1987. The newer rudders use a black plastic cam to lock the rudder in the down position. Locate the left and right rudder assemblies. The left one has a red dot and the right one a green dot.
13 RUDDER AND TILLER CROSS BAR INST ALLA TION (Pre 1987 boat s) 1. Disengage the tiller arm from the lower casting and lock the tiller arm and rudder in the kicked up position. This will pull the rudder blade up and out of the way so the rudder pin can be installed.
14 RAISING THE SAILS 1. Point the boat into the wind before you begin this operation. 2. Lay the main sail out on the trampoline. Insert the battens into the batten pockets starting at the top of the sail and working your way down. The batten has a tip on each end.
10. Attach the three boom blocks to the hangers on the boom. Secure the ratchet block to the top of the traveler car. Thread the mainsheet through the blocks as shown in Figure 37. Slip the other end of the mainsheet through the traveler jam cleat, then guide the line through the center of the traveler, and secure at the dead eye on the back bar.
16 Raising the Jib 1. Attach the shackle on the end of the jib halyard wire to the head of the jib. 2. Wrap the luff pocket of the jib around the forestay and engage the zipper an inch or so. Next thread the jib halyard line inside the luff pocket. See Figure 38.
DAGGER BOARDS 1. Slip the shock cord through the hole in the upper portion of the dagger board, take both ends to the hole on the out board deck flange. Pass both ends through the hold and tie a knot under the rail. 2. Pass the rope handle through the same hole in the dagger board as before.
HOBIE CA HOBIE CA T 18 T 18 ’ ’ 18.
19 INDEX NO. DESCRIPTION 1 Arm 2 Brace 3 Slide 4 Diamond Wire (one side) 5 Gooseneck Y oke 6 Check Block 7 Mast Rotation Line 8 Modified Swivel Block 9 Shackle 10 Mast Rotation Assembly 1 1 Pin-Pawl Bearing, 5.5. 12 Ring-Halyard Line 13 Hook for Halyard Lock Assembly 14 Jib Furling Assembly 15 Bridle Wire Assembly 16 Screw - 5.
20 Illustration No. 1 Mast Assembly 1-1 Spreader Arm 1-2 Spreader Root 1-3 Clevis Pin 3/16" x 11/16" 1-4 Slide 1-5 Clevis Pin 3/16" x 13/16" 1-6 Brace 1-7 Clevis Pin 3/16" x 9/16" 1-8 Cotter Pin 1-9 Mast Rotation Control Yoke 1-10 Block 1-11 Shackle 1-12 Bolt 4-1/8" Lg.
21 Illustration No. 2 Jib Halyard Assembly 2-1 Jib Block Housing 2-2 Jib Halyard Wire 2-3 Luff Tensioner 2-4 Jib Halyard Line 2-5 Jib Block Sheave 2-7 Clevis Pin 2-8 A Cotter Pin 2-9 Swedge 2-10 Thimble 2-11 Block 2-12 Shackle Illustration No.
22 *Rudder system Pre-1987 shown Illustration No. 6 Rudder Assembly 6-1 Rudder Blade-Drilled 6-2 Lower Rudder Casting Assembly 6-3 Port Upper Rudder Housing Assembly 6-4 Nut Nylock 6-5 Bolt 2" Lg 6-6 Spring 6-7 Delrin Screw 6-8 1 / 4" I.
Illustration No. 8 T raveler Assembly 8-1 1- 1/4" Lg H.H. Bolt 8-2 Deck Plate 8-3 Sheave 8-4 Spacer 8-5 Car Assembly 8-6 Cotter Pin 8-7 H.H. Nuts-Nylock 8-8 Bearing Cylinder 8-9 Pin-Clevis 8-10 Bearing Ball Illustration No.
Illustration No. 10 (old style) Dolphin Post Assembly 10-1 Screw RHMS 10-2 Internal Lock Washer 10-3 Washer 10-4 Mast Step Pad 10-5 Bushing 10-6 Mast Step Casting 10-7 Dolphin Striker Post 10-8 Dolphin Striker Sleeve Illustration No.
Illustration No. 12 (new style) Tiller Connector 12-1 Tiller Connection Rod 12-2 Tiller Arm Swivel End Cap 12-3 Tiller Arm Insert 12-4 Bolt 12-5 Washer 12-6 Insert Bearing 12-7 Retainer Clip 12-8 Screw Part s Relating to Diagram on Page 2 11 Trapeze Seat Assy.
26 SAILING YOUR HOBIE 18’ Safe and sane guideline for the beginner; and an easy review for the experienced. Always wear a life jacket when boating. BALANCING THE BOAT When sailing, sit on the upwind side of the boat (wind on your back) just in front of the tiller, facing the sail.
27 TURNING To tack or turn the boat into and across the wind to the opposite direction (also known as "coming about"), follow the points of sail guide illustration and take the boat to the close hauled point of sail. This is when you are nearly 35 degrees from sailing straight into the wind.
28 line while slowly leaning back away from the trampoline. Lean to approximately 45 degrees for best leverage. As the mast and sail lift out of the water and the upper hull begins to drop back into the water, drop down to your knees then into the water.
29 6) Hobie Cat rudder blades are preset to break away from the locked down position at 17-26 pounds by testing with a line around the rudder blade seven inches above the lowest tip of the blade. Once the rake is changed, the breakaway tension should be rechecked.
A good anti-fouling paint can be applied for some protection from marine growth before mooring. Before painting, it is suggested that the area be masked off to ensure a clean line. No friction reducing paints or agents may be employed on a Hobie Cat during competition.
About your Hobie 18’ There are ways of going faster on a catamaran, while still staying within the eight foot beam, trailerable size range. Basically, you put a taller mast on, use daggerboards, and go to a half round hull shape.
CA UTION / SAFETY TIPS • Watch for overhead power lines. Never rig, trailer or sail the boat near overhead power lines. Contact with a power line could be fatal. • Install Drain Plugs. Even the most experienced of boaters forget to install the drain plugs sometimes.
デバイスHobie 18 SEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hobie 18 SEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHobie 18 SEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hobie 18 SEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hobie 18 SEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hobie 18 SEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHobie 18 SEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hobie 18 SEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHobie 18 SEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
