Hondaメーカー08E91-E22-100Bの使用説明書/サービス説明書
ページ先へ移動 of 22
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 1 of 22 08E92-SVA-1B00-91 FEB 2008 200 6-2008 CIVIC 2-DOOR (A/T ONLY) REMOTE ENGINE STARTER SYSTEM INSTALLATION INSTRUCTIONS Accessory Application Publications No.
2 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 7 Foam cushion tapes Flange nut Clip Green relay (5-pin) Template Illustration of the Engine Starter System.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 3 of 22 Setting the Control Unit 3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach.
4 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 9. Remove the driver’s dashboard lower cover (eight clips). 5202121T DRIVER’S DASHBOARD LOWER COVER 8 CLIPS 5202112T 8. If equipped, remove the driver’s dashboard under cover (turn the knob counterclockwise, and release two clips and pin).
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 5 of 22 1 2. Remove the column lower cover (two self-tapping screws and one screw). 5308530T 2 SELF-TAPPING SCREWS SCREW COLUMN LOWER COVER 1 0 . Lower the tilt lever, and pull the steering wheel toward you.
6 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 4 . Remove the sunvisor holders. Using a small flat- tip screwdriver, push the hook, and turn the holder 90°, then pull it out.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 7 of 22 1 9 . Pull away the weatherstrip from the left front pillar trim. Remove the left front pillar trim (two clips). 5202100T 2 CLIPS LEFT FRONT PILLAR TRIM WEATHERSTRIP 2 0 .
8 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 2 4. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown. 2 5 . Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 9 of 22 2 8. Route the antenna cable under the roof liner towards the driver’s side of vehicle, and down along the vehicle harness. Be careful not to crease the roof liner.
10 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 2 . Secure the antenna cable to the vehicle harness with a wire tie. Secure the wire tie between the vehicle harness branching points. 6D01281T VEHICLE HARNESS WIRE TIE ANTENNA CABLE BRANCHING POINT Installing the Control Unit Bracket 3 3 .
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 11 of 22 3 5 . Install the four relays to the engine starter harness relay blocks. Be careful to install the relays properly, or a malfunction will result. Routing the Engine Starter Harness 3 4 .
12 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 3 8 . Disconnect the vehicle 8-pin connector on the rear of the wiper switch and plug the engine starter harness 8-pin connectors into the vehicle 8-pin connector.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 13 of 22 4 0 . Wrap the vehicle 7-pin connector with one foam cushion tape, then place the vehicle 7-pin connector into the gap of the column. 6D01111T VEHICLE 7-PIN CONNECTOR (brown) (Squeeze into this area.
14 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 4 7 . Secure the engine starter harness to the vehicle harness using a wire tie: • With driver's dashboard under cover: Secure in the hole opened in the instrument panel.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 15 of 22 4 9. Disconnect the vehicle 42-pin, 4-pin, and 2-pin connectors. 5 1 . Wrap foam cushion tape to the vehicle 2-pin and 4-pin connectors and secure them with a wire tie.
16 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 5 4 . Install the clip from the engine starter harness to the fuse box bracket behind the fuse box.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 17 of 22 6D01312T ANTENNA CABLE TERMINAL (Connect first.) FRONT CONTROL UNIT ENGINE STARTER HARNESS 18-PIN CONNECTOR CONTROL UNIT BRACKET 5 7 . Install the control unit on the control unit bracket.
18 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 752501AS CAR ICON 752502AS CHECK BUTTON Input the VIN and other required information. 752504AS Select “R/C ENG STARTER.” CHECK BUTTON 752503AS Select “Honda Systems.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 19 of 22 752505AS “REMARKS” message CHECK BUTTON 752506AS Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” CHECK BUTTON 752507AS “Obtain PCM-code" message CHECK BUTTON 752509AS Input the PCM code.
20 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. 1 1 . The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. 1 2. The following message will display: Check that the engine can be started by the Transmitter.
© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38215-38958 (0802) 21 of 22 732904A Y DISPLAY COMMAND BUTTON START BUTTON TRANSMITTER STOP BUTTON FUNCTION CHECK Operating Conditions • The hood is closed. • The shift lever is in Park.
22 of 22 AII 38215-38958 (0802) © 2008 American Honda Motor Co., Inc. - All Rights Reserved. How to Program an Additonal Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle's VIN and other required information.
デバイスHonda 08E91-E22-100Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Honda 08E91-E22-100Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda 08E91-E22-100Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda 08E91-E22-100Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda 08E91-E22-100Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda 08E91-E22-100Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda 08E91-E22-100Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda 08E91-E22-100Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda 08E91-E22-100Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
