Hondaメーカー08V67-TE0-100Aの使用説明書/サービス説明書
ページ先へ移動 of 15
Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application © 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 1 of 15 08V67-TE0-1000- 91 AII 375.
2 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. Flange bolt, 6 x 12 mm Flange nut 4 Harness ta pes Accessory User’s Information Manual Back-up Sens.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 3 of 15 2. Disconnect the negative cable from the battery. 3. Remove the two covers from the rear bumper and remove the rear bump er (two bolts, six self-tapping screws, two clips, and unplug one conne ctor).
4 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 8. Using the trim tool, r emove the rear shelf access panel, then releas e the front rear sp eaker retaining tab. 9. Remove the left rear speaker cover (ni ne retaining tabs).
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 5 of 15 L4 Model 12. Ins tall the cont rol unit to th e vehicle panel: • Partially thread the 6 mm flange nut onto the control unit bracket stud. Inse rt the control unit bracket stud into the hole in the vehicle panel.
6 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 13. Attach the 2A fuse label to the fuse ca se on th e back-up sensor harness.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 7 of 15 15. At the left taillight, secure the back-up sensor harness to the vehicle h arness wit h one wire t ie. 16. Plug the back-up sensor harness 14 -pin connector into the co ntrol unit, and rou te the harness fo rward along the vehicle harn ess.
8 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 17. Sec ure the back-up sensor harne ss to the vehicle harness with two additional wire ties at the locations shown. L4 Model 742401CE VEHICLE HARNESS BACK-UP SENSOR HARNESS 2 WIRE TIES VEHICLE HARNESS BACK-UP SENSOR HARNESS WIRE TIE V6 MODEL 18.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 9 of 15 19. Using scissors cut one urethane tape in half, and then cut one of the halves again. Wrap the cu t pieces around the bee per harness shown . 20. Install the connector clip to the beeper 2-pin connector.
10 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 742408CE BACK-UP SENSOR HARNESS WIRE TIES WIRE TIE TRUNK ROOM VEHICLE HARNESS 28. Install one wire tie with clip to the holder with the fuse case, and attach the wire tie to the vehicle harness.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 11 of 15 32. Install one wire tie with h older to the b ack-up sensor harness 16-pin connector , and attach the wire tie to the vehicle harness.
12 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 34. While wearing eye protec tion drill the rear bumper: NOTE: Center sensors are 26 mm holes, side sensor s are 24 mm holes. • From the outside of t he bumper, drill all eight pierced marks using a 3 mm drill bit.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 13 of 15 36. Ins tall two center se nsors into th e 26 mm holes in th e rear bumper using the sensor clip s. Note the direction and location for each sensor. 37.
14 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 41. Using isopropyl alcohol on a shop towel, clea n the area where the harness tapes will attach. 42. At each green tape location, attach the back-up sensor subharness to the rear bumper with four harness tapes.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 15 of 15 44. Check that all wire harnesses are routed pr operly and that all connectors are plugge d in. 45. Rein stall all removed part s. 46. Reconnect the negative cable to the battery.
デバイスHonda 08V67-TE0-100Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Honda 08V67-TE0-100Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda 08V67-TE0-100Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda 08V67-TE0-100Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda 08V67-TE0-100Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda 08V67-TE0-100Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda 08V67-TE0-100Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda 08V67-TE0-100Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda 08V67-TE0-100Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
