Honda AutomobilesメーカーSB7038の使用説明書/サービス説明書
ページ先へ移動 of 32
.
SB7038 Snowblower The information in this operator’s manual is limited in application to the Honda SB7038 Snowblower when installed and used on a Honda mid-sized commercial mower power head. Before installing or operating this equipment, read this operator’s manual and the owner’s manual supplied with the power head.
SB7038 Snowblower Table Of Contents THE IMPORTANCE OF INSTALLATION ....................................................................................... 3 IMPORTANT SAFETY PRECAUTIONS.. ...............................................................
8 0 8 8 THE IMPORTANCE OF INSTALLATION Proper installation is essential to operator safety and the reliability of the machine. Any error or oversight made by the technician assembling and servicing a unit can easily result in faulty operation, damage to the machine, or injury to the operator.
SB7038 Snowblower Safety Labels Immediately replace any label that becomes damaged or unreadable. Contact a servicing Honda commercial mower dealer for replacement label. FAILURE TO FOLLOW SAFE OPERATING PROCEOU RES MAY RESULT IN INJURY. l FOR SAFE OPERATION FOLLOW ALL OPERATlNG INSTRUCTIONS AND SAFETY PRECAUTIONS IN OPFRATcX?S MANUAL.
- SB7038 Snowblower Assembly and Installation Assembly and Installation 1. 2. 3. Remove the lag bolts holding the blower head and the pulley assembly to the shipping pallet. Remove the blower head and pulley assembly from the pallet. Remove the loose parts box, then inventory the contents.
Assembly and Installation SB7038 Snowblower Inventory Large Hardware Bag There is a large and small hardware bag. The hardware in the large bag are used for the initial assembly and installation, while the hardware in the small, resealable bag consists of spare shear bolts.
SB7038 Snowblower Assembly and Installation a Hardware Measuring Chart How to measure hardware and components: INCHES 0 1 2 3 4 5 6 IIIl,lllI IIll,IIII llll,IIII I I I I,,,,,,,, I IllIll ,,,,,,,,, I 0.
Assembly and Installation SB7038 Snowblower Remove the Mower Deck 1. Follow the procedure in the HRC 7000~series Owner’s Manual or Shop Manual and remove the mower deck from the power head. 2. Save the bolts and flange nuts to use with the mower deck when it is reinstalled.
SB7038 Snowblower Assembly and Installation 6. 7. a. 9. Hold one of the face plates behind the opening in the engine bed. Slide the threaded end of the release rod through the opening and the slot in the face plate. Thread the release rod into the pivot pin until the edge of the welded plate on the rod is 3 mm (l/W) from the engine bed.
3. 4. 5. 6. 7. Assembly and Installation SB7038 Snowblower Lightly coat the top side of the anti-friction 114 x 314” HEX BOLT (2) l/4 x 112” HEX BOLT (6) ring with general purpose grease, and place it over the chute base. The ring is WORM GEAR keyed and will only fit on the chute base l-511 6” one way.
SB7038 Snowblower Assembly and Installation Install the Snowblower 1. 2. 3. 4. Check that the power unit is in “Low Range” at the 2-l/2” cutting-height position. Refer to the mid-sized commercial mower owner’s manual or shop manual as needed. Loosen the two belt guards around the crankshaft pulley.
Assembly and Installation SB7038 Snowblower Chute Rotator Assembly 1. Install the crank support on the power head with two 3/8 x 1” bolts and flange nuts.
SB7038 Snowblower Assembly and Installation Deflector Cable Assembly 1. 2. 3. 4. 5. Remove the forward throttle mounting screw, and use it to temporarily hold the cable bracket in position. The cable bracket will be used as a guide to mark, and drill the two mounting bolt holes in the handle tube.
Assembly and Installation SB7038 Snowblower 6. 7. 8. Route the cable behind the fuel tank and above the the speed control arms. On 7018/20 models, thread the cable through the same slot on the fuel support bracket used by the choke and throttle cables.
SB7038 Snowblower Safety Recommendations Safety Recommendations Introduction 1. 2. The snowblower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
Safety Recommendations SB7038 Snowblower 1. Before each use, clear work area of objects such as rocks, toys, wire, sleds, etc., which could be picked up and thrown. 2. Keep the snowblower in safe operating condition. Check the following each time before use: a) b) c) 4 All hardware for tightness (refer to the torque table for details).
SB7038 Snowblower Safety Recommendations - lO.As a general rule, do not operate the snowblower in reverse. If it is absolutely necessary to back up: a) Disengage the blade control. b) Check the area on the ground directly behind the machine. c) Continue to observe area down and to rear while backing up.
Safety Recommendations SB7038 Snowblower Stopping 1. Before leaving operator’s position or leaving the machine unattended: a) Bring the snowblower to a complete stop. b) Move the blade control lever to OFF. c) Move the speed control levers to NEUTRAL.
SB7038 Snowblower Safety Recommendations a a a a a a a Controls Use this section to familiarize yourself with the various controls and operation of the snowblower. This section covers only items relating to the snowblower itself. Refer to the owners manual for the Honda mid-size commercial mower for instructions in operating the power unit.
Safety Recommendations SB7038 Snowblower 6. 7. 8. 9. Inspect the position of the two skid shoes and make sure they are properly positioned for conditions. Allow l/8” to 3/l 6” clearance between cutting edge and a level paved surface, or l/4” to l/2” for an uneven or gravel surface.
SB7038 Snowblower Safety Recommendations OKAY TO DISCHARGE SNOW TO THIS SIDE Snow Removal Methods 3 Use the following patterns to avoid discharging snow in unwanted locations and to also prevent a second pass. For clarity, assume both methods are used on a rectangular area.
Removing and Storing the Snowblower SB7038 Snowblower Removing and Storing the Snowblower Refer to the illustrations in the installation section as needed. Deflector Cable Removal 1. Loosen the deflector cable nut at the operator’s end, and remove the cable from the chute control cable bracket.
SB7038 Snowblower Maintenance & Adjustments Maintenance & Adjustments Maintenance Schedule What When Notes Lubricate chains Every 2 hours use chainsaw oil Apply grease to antifriction ring Eve.
Maintenance & Adjustments SB7038 Snowblower Gearbox Oil The oil level in both the front and rear gearbox must be checked every 25 hours. Park the snowblower on a flat, level surface. Remove the belt cover. Locate the oval cutout in either side of the the rear gearbox mounting bracket.
SB7038 Snowblower Parts Listing Parts Listing a BUSHING, SPLITTAPER (1.0’ BORE) 1 6 CABLE ASSY, CHUTE CONTROL ( 1 7 CV MP ASSEMBLY (1 6 CO’. -. ., WC.. 9 ,,cn REIT I1 9 KNOB, BELT COVER 2 10 SNOW THROWER ASSY, 36 1 11 GEARBOX 1 12 SPROCKET, 11 TOOTH 1 13 SPROCKET, 32 TOOTH 1 14 CHAIN, l/Z’PlTCH 1 - - - - , -, .
Parts Listing SB7038 Snowblower Auger and Fan I blower head 1 ! auger blade, left 1 3 auger blade, right 1 4 fan, camp. 1 j fan shaft support 1 ; gearbox bracket 1 7 bearing support 2 3 front gearbox 1 3 auger shaft 1 10 fan shaft holder 1 11 fan shaft bearing 1 12 bearing support 1 13 woodruff key, 1 1/4x 718” 14 lbolt.
SB7038 Snowblower Parts Listing Discharge Chute - POP 52173 (9511) 27.
Optional Accessories SB7038 Snowblower Optional Accessories A number of accessories are available for your snowblower to enhance operation and use. Headlight Kit This is a single-lamp light kit that mounts to the crank support rod. The light features an integrated, weather-resistant on/off switch and 50 watt halogen bulb.
SB7038 Snowblower Warranty Service Information Warranty Service Information Honda Power Equipment dealerships are staffed by trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management.
Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are trained professionals.
q uuuunnnnucuunucnnnnucunnnnucunn q cInnnnnnnnunnnnnnunnnnnnnnunnnnn q uuunnnnnnnnnnuunnnuunnnnnunnnnn q uuuunuunnccnuunccccunucccunncq q LI~n~~n~~n1Ui-l~i~iICI~uIICl~~C-Il[?nCI7I~Cl;~ nnnnnnlinnnnnnn.
デバイスHonda Automobiles SB7038の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Honda Automobiles SB7038をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda Automobiles SB7038の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda Automobiles SB7038の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda Automobiles SB7038で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda Automobiles SB7038を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda Automobiles SB7038の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda Automobiles SB7038に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda Automobiles SB7038デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
