Honda Power EquipmentメーカーGPX 165の使用説明書/サービス説明書
ページ先へ移動 of 28
0306 © 2006 SprayTECH. All rights reserved. Fo rm N o. 0 55 58 90 A Printed in the U. S. A. GP X 165 Gas P iston P ump Do not use this equipment before reading this manual! SprayTECH 1770 Fernbrook Lane Minneapolis, MN 55447 T echnical Assistance: 1-800-292-4637 Order Entry: 1-800-443-4500 Fax: 1-800-525-9501 www .
T able of Contents S afety Precautions .................................................................2 F rançais ..............................................................................18 E spañol ...........................................
3. Always use the nozzle tip guard. Do not spray without the nozzle tip guard in place. 4 . Only use a nozzle tip specified by the manufacturer . 5. Use caution when cleaning and changing nozzle tips.
General Description T his airless sprayer is a precision power tool used for spraying m any types of materials. Read and follow this instruction m anual carefully for proper operating instructions, m aintenance, and safety information. Operation This equipment produces a fluid stream at extremely high pressure.
4. Move the PRIME/SPRA Y valve to the PRIME position. 5. Move the engine ON/OFF switch to the ON position. 6. Start the engine: a. Open the fuel valve lever . b. Move the throttle lever away from the gas tank. c. Close the engine choke lever . d. Holding the frame with one hand, pull the starter rope rapidly and firmly .
Pressure Relief Procedure Be sure to follow the pressure relief procedure when shutting the unit down for any purpose, including servicing or adjusting any part of the spray system, changing or cleaning spray tips, or preparing for cleanup. 1. Lock the gun by turning the gun trigger lock to the locked position.
Cleanup Special cleanup instructions for use with flammable solvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal c ontainer , place it into an empty five gallon container , then f lush solvents.
3 . Make certain that the service area is well ventilated in c ase solvents are used during cleaning. Always wear p rotective eyewear while servicing. Additional protective equipment may be required depending on the type of cleaning solvent. Always contact the supplier of solvents for recommendations.
Replacing the Potentiometer Electrostatic discharge (ESD) potential could cause damage to electronic pressure control. Use SprayTECH ESD wrist strap P/N 0507958 or equivalent when working on electronic pressure control. 1. Perform the Pressure Relief Procedure.
Replacing the T ransducer Electrostatic discharge (ESD) potential could cause damage to electronic pressure control. Use SprayTECH ESD wrist strap P/N 0507958 or equivalent when working on electronic pressure control. 1. Perform the Pressure Relief Procedure.
Replacing the Slider Assembly and Slider Housing 1. Start the engine (refer to the procedures in the Operation section of this manual). T urn the pressure control knob clockwise to its maximum pressure setting.
Replacing the Gears 1. Perform the Pressure Relief Procedure. 2. Using a Phillips screwdriver , remove the four front cover screws. Remove the front cover .. 3 . Using a 7/8” open-end wrench, loosen and remove the f luid hose from the fitting on the back of the fluid section.
8. Locate the clutch hub and armature assembly on the end of the engine shaft. Note the two set screws as well as the unused, threaded hole in the taper lock bushing at the center of the clutch hub. 9. Using an 1/8” hex wrench, remove the two set screws from the taper lock bushing 1 0.
5 . Line up the four holes around the outside of the clutch f ield with the four set screw holes in the gear housing. T he clutch field wires should be at approximately the 1 or 2 o’clock position. 6. Route the two clutch field wires through the grommet and into the EPC housing.
9. Using a wrench, turn the jam nut counterclockwise to loosen it from the pump housing. 1 0. Turn the fluid section c ounterclockwise to remove it f rom the pump housing. 1 1. Place the fluid section cylinder upright in a vise by clamping on the wrench flats.
4 5. Continue to turn the cylinder clockwise until the jam nut is f lush against the pump housing. 4 6. Once the nipple is positioned, turn the jam nut clockwise u ntil it contacts the pump housing. 47. Tighten the jam nut with a wrench to tighten it against the pump housing.
© SprayTECH. All rights reserved. 17 T roubleshooting P roblem The unit will not run. The unit will not prime. The unit will not build or maintain pressure. Fluid leakage at the upper end of the fluid section. Excessive surge at the spray gun. Poor spray pattern.
18 © SprayTECH. T ous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant être lus attentivement avant toute utilisation de l'appareil.
© SprayTECH. T ous droits réservés. 19 6. Ne laissez pas l’appareil sous tension ou sous pression quand vous vous en éloignez. Quand vous n’utilisez pas l’appareil, éteignez-le et libérez la pression conformément aux instructions du fabricant.
20 © SprayTECH. T odos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprender antes de usar el equipo. Cuando se encuentre con uno de los siguientes símbolos, asegúrese de observar sus indicaciones de seguridad.
© SprayTECH. T odos los derechos reservados. 21 9. Este sistema es capaz de producir 3300 PSI / 22.8 MPa. Utilice solamente piezas de repuesto o accesorios especificados por el fabricante y con una capacidad nominal de 3300 PSI como mínimo.
22 © SprayTECH. All rights reserved. Parts List Main Assembly.
© SprayTECH. All rights reserved. 23 Item Part # Description Quantity 1 9850936 ON/OFF switch ...........................................1 2 0509558 Electronic pressure control assembly .........1 3 0509556 Screw .....................................
24 © SprayTECH. All rights reserved. Fluid Section Assembly (P/N 0509144).
© SprayTECH. All rights reserved. 25 Cart Assembly Item Part # Description Quantity 1 0507766 Handle (includes items 2–5, 1 1, and 12) ....1 2 9841504 Snap button ................................................2 3 0295609 Handle washer ...........
26 © SprayTECH. All rights reserved. PRIME/SPRA Y V alve Assembly (P/N 0507690) Item Part # Description Quantity 1 0507736 Dowel pin ....................................................1 2 0507745 Gasket ..............................................
© SprayTECH. All rights reserved. 27 Accessories Part No. Description 0550xxx T ip Assembly 0297078 T ip Guard (1 1/16”) 0297070 T ip Guard (7/8”) 0508342 Hose, 25’ x 3/8” 0291006 Hose, 50’.
28 © SprayTECH. All rights reserved. Limited W arranty S prayTECH, a division of W agner Spray T ech Corporation ("SprayTECH"), warrants that at the time of delivery to the original p urchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship.
デバイスHonda Power Equipment GPX 165の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honda Power Equipment GPX 165をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHonda Power Equipment GPX 165の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honda Power Equipment GPX 165の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honda Power Equipment GPX 165で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honda Power Equipment GPX 165を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHonda Power Equipment GPX 165の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honda Power Equipment GPX 165に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHonda Power Equipment GPX 165デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。