Honeywellメーカー220736Bの使用説明書/サービス説明書
ページ先へ移動 of 12
CONTENTS Specifications ................................................ 2 Ordering Information .................................... 2 Installation .................................................... 2 Setting and Adjustments ........................
Specifications 2 MODELS: 220736A,B Internal Auxiliary Switches for TRADELINE Modutrol IV Motors. Switches are actu- ated by cams in the motor. The cams can be set to operate the switches at any point in the motor stroke. 220736A—Includes one Spdt Micro Switch V3 snap acting switch, mounted on left side and operated by outer cam.
8. Lower the switch assembly into place and tighten the two mounting screws, making sure the switch follow- ers are properly aligned with the inner and outer cams in the motor.
TABLE 1—AUXILIARY SWITCH LEADWIRE COLORS FOR LOW AND MEDIUM TORQUE SERIES 91 MOTORS WITH ONE AUXILIARY SWITCH. Replace with 220736A,B Factory-Installed Auxiliary Switch Leadwire Color a,b Leadwire Left Auxiliary Switch N.O. Yellow W/Yellow Orange N.
Replace with 220736A,B Factory-Installed Auxiliary Switch Leadwire Color a,b Leadwire Left N.O. Blue Blue W/Yellow Purple Auxiliary N.C. Yellow Yellow W/Blue Orange Switch Com. Red Red W/Red Red Right N.O. B/Blue B/Yellow B/Purple Auxiliary N.C. B/Yellow B/Orange Switch Com.
TABLE 4—AUXILIARY SWITCH POSITION WITH MOTOR SHAFT ROTATED TO EITHER SIDE OF AUXILIARY SWITCH OPERATING POINT, AS VIEWED FROM POWER END. Auxiliary Switch Contact Positions N.
To turn the cams, insert small screwdriver (1/8" or 3 mm blade) through wiring box into slot on cam and move the screwdriver at the top. Refer to Fig. 3. Each division on the cam represents 15 ° of motor rotation. A) Two position motors (M8185): 1.
7. Check for proper switch differential and switching of auxiliary equipment by driving the motor through full stroke (in both directions) using the potentiometer. If necessary repeat steps 5 and 7 for 1 ° differential, or 6 and 7 for 10 ° differential until correct switching action is obtained.
220736A,B SETTINGS AND ADJUSTMENTS 5. For switch differential of 10 ° , the cams must be rotated with screwdriver approximately 180 ° prior to setting the switching action. Refer to Fig. 3. Check continuity of the N.O. (Red to Purple) contacts and rotate cams as follows: a.
10 Fig. 8 — Auxiliary switch adjustment for M6184, M6194 motors. 4. For switch differential of 1 ° , check continuity of auxiliary switch N.O. (Red to Purple) contacts and, with screwdriver, rotate cam as follows: a. If contacts are open, rotate cam clockwise until N.
W ARNING FIRE OR EXPLOSION HAZARD CAN CAUSE SEVERE INJURY OR DEATH When auxiliary switches control combustion equipment, incorrect wiring of the switches can allow the burner to come on at high fire. Check auxiliary switch wiring and cam adjustment be- fore turning on the system.
220736A,B SETTINGS AND ADJUSTMENTS Residential and Residential and Helping You Control Your World Building Controls Division Building Controls Division Honeywell Inc.
デバイスHoneywell 220736Bの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honeywell 220736Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell 220736Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell 220736Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell 220736Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell 220736Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell 220736Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell 220736Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell 220736Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。