HoneywellメーカーHD28W4HR6Xの使用説明書/サービス説明書
ページ先へ移動 of 20
Document 900.0275 – 10/05 – Rev 1.01 Installation Guide Premium V andal Dome Camera NTSC / P AL HD28C4HR6 HD28C4HR6X HD28C4HR9 HD28C4HR9X HD28W4HR6 HD28W4HR6X HD28W4HR9 HD28W4HR9X HD28D4HR6 HD28D4.
Revisio ns Issue Date Revisions 1.00 09/05 New document. 1.01 10/05 Changed HD28R to HD28 throughout, removed utp & fiber termination boards updated back cover.
Rev 1.01 iii Document 900.0275 10/05 W arnings Installation and servicing should be perf ormed only by qualified and experienced technicians to conform to all local co des and to maintain your warranty. WARNING! The use of CSA Certified/UL Li sted Class 2 power adapters is required to ensure compliance with electrical safety standards.
Rev 1.01 iv Document 900.0275 10/05 FCC Compliance Statement Information to the User : This equipment has been tested and found to comply with the limits for a Class A digital device.
Rev 1.01 Document 900.0275 10/05 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Unpack Everything .
Rev 1.01 1 Document 900.0275 10/05 Introduction The HD28 Series is Honeywell’s pre mium li ne of vandal-resista nt, fully-integrated CCTV cameras. The HD28 series enclosure is designed for easy installation and setup. Before Y ou Begin Unpack Everything Check that the items received matc h those listed on the order form and packing slip.
Rev 1.01 2 Document 900.0275 10/05 Installation Your HD28 camera is weather- seale d for indoor or outd oor locations. The wiring can be completely concealed for maxi mum vandal and tamper resistance. Mounting the Camera The HD28 camera is designed to be surface mounted on a wall or ceiling.
Rev 1.01 3 Document 900.0275 10/05 Installing the Conduit Plug Your HD28 enclosure comes with a conduit plug pre-installed in the 1/2” conduit entry on the back of the housing. This plug may be removed and installed in the side 3/4” conduit entry (see Figure 2 ).
Rev 1.01 4 Document 900.0275 10/05 Wiring Options Your HD28 Series camera is supplied with a coaxial termination board mounted to the bottom of the enclosure. A ll connections are made here (see Figure 3 ). Figure 3 Wiring Options Connecting the Wiring 1.
Rev 1.01 5 Document 900.0275 10/05 Figure 4 Gimbal Adjustment Adjusting the Lens F ocus Lenses are pre-focused at the factory but may require a final adjustment after installation in the unlikely event the optical ef fect of the dome causes a slight defocusing of the lens.
Rev 1.01 6 Document 900.0275 10/05 Dip Switch F unctions (Color Cameras, Including TDN Models) Follow Figure 5 to set the dip switches on a color camera.
Rev 1.01 7 Document 900.0275 10/05 Adjustment Method (Color Cameras) White Balance Adjustment Method (Color Cameras) Switch no. Function Off On 1 GAMMA Off (0.
Rev 1.01 8 Document 900.0275 10/05 Manually Setting Shutter Speed (Color Cameras) To manually set the shutter speed, turn sw itch #2 to the ON position; then set switch #3, #4, and #5 for the desired shutter speed (see Figure 5 ). FLON and BLC can be set when switch #2 is set to the OFF positi on.
Rev 1.01 9 Document 900.0275 10/05 Dip switch functi ons (WDR cameras) Figure 6 Wide Dynami c Range Camera Switch Settings Note The Wide Dynamic Range camera has been designed for the best wide dynamic performance and can only be used with vari-focal auto iris lenses.
Rev 1.01 10 Document 900.0275 10/05 Adjusting the Line Lock (V ertical Phase) for 24 V AC Operation Phase adjustment may be necessary in mu ltiple camera installations to prevent picture roll when switching between two ca meras.
Rev 1.01 11 Document 900.0275 10/05 Routine Maintenance Use regular liquid cleaners to remove dirt and grime from the dome. Caution Do not use harsh or abrasive cleaners which can scratch the polycarbonate dome and reduce visibility for the camera.
Rev 1.01 12 Document 900.0275 10/05 W arranty and Service Subject to the te rms and conditions listed on the product warranty, during the warranty period Honeywell will repair or re place, at its sole option, free of charge, any defective products returned prepaid.
Rev 1.01 13 Document 900.0275 10/05 Specifications Note Specifications apply to all camera models, unless otherwise noted. Video Signal Specif ications Pickup device: 1/3 in.
Rev 1.01 14 Document 900.0275 10/05 Cable Guidelines Power supply cable maximum len gth (feet/meters) Cameras with AC/DC power supplies Wire gauge Power supply 24 AWG 22 AWG 18 AWG 16 AWG 15 VDC 45/14.
Video Systems www.honeywellvideo.com +1.800.796.CCTV (North America o nly) © 2005 Honeywell International Inc. All rights reserved. No p art of this publicatio n may be reproduced by any means without written permission from Honeywell Video Sy stems.
デバイスHoneywell HD28W4HR6Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honeywell HD28W4HR6Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell HD28W4HR6Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell HD28W4HR6Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell HD28W4HR6Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell HD28W4HR6Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell HD28W4HR6Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell HD28W4HR6Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell HD28W4HR6Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。