HotpointメーカーWM83の使用説明書/サービス説明書
ページ先へ移動 of 20
Instruction Manual F or Models WM81 and WM83 Congratulations on the pur chase of your new Aquarius Washing Machine . IMPORT ANT INFORMA TION Please read this instruction book thoroughly before installing and using your appliance for the first time .
W ARNING: This appliance must be earthed. F uses Y our appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse , only those rated at 13A and AST A approv ed to BS1362 should be used.T o change fuse, lif t holder to vertical position and lift the fuse out.
3 Electricity Supply ...................................... 2 Recycling & Disposal Information .............. 3 Installation Instructions 1. Choose a L ocation................................ 4 2. Remo ve T ransit Bracket ....................... 5 3.
1. Choose a Loc ation... The choice of location f or your appliance will influence its pe rformance. ● Position wher e possible on a solid floor . Vibration may occur wi th a wooden floor . ● T ake care with vinyl floor coverings. The weight of the appliance may cause inden tations in some vinyl floor co verings.
5 W ARNINGS ● Before using appliance, remove tr ansit bracket , clamp and screws Retain parts for future transportation. ● Do not remove concrete weight. Replace work top lid and 3 screws. Remove 2 screws and transit bracket, retain. Remove 1 screw and clamp , retain.
3. Connect to the W ater Supply ... ● Incoming hot and cold water pr essure should be between 3 and 150 psi (21 - 1034 Kpa). ● The temperatur e of the incoming household hot water supply shou ld ideally be 60°C and no higher than 70°C as this c ould cause damage to both your laundr y and appliance .
4. Connect to a Dr ainage Syst em... ● Do not remove hooked end support from drainage hose. ● Do not position standpipe near an electrical outlet. ● F or drainage into a standard work top sink ensure outlet pipe has a minimum bore of 32 mm. T o avoid syphoning ensure the end of the drainage hose is above the wat er level in the sink.
G etting t o K now Y our Applianc e Index Fro n t 1. Door Locked Indicator 2. Mains On/Off Button. 3. W ash Dial 4. V ariable T emperature Contr ol Dial 5. V ariable Spin Speed Control Dial 6. Optional Wash F eature Buttons 7. Interlocking Door & Release Button 8.
9 V ariable T emper ature Control Dial ● T o reduce the wash temperature of an y programme except J’ , turn the dial before selecting a programme . ● T o protect laundr y , you are unable to increase automa tic tempera ture settings. Note: W e do not recommend using the NO HEA T setting with the prewa sh programmes A or B.
IMPORT ANT INFORMA TION: Before selecting a programme, ensure the ma ins button is in the ‘OFF’ position. Add detergen t and or conditioner to the dispenser drawer , see pages 14-15.
11 Approx. Prog . Time Max. (mins) Spin Speed ITCL T emp F ull based on hot depending Prog . Codes F abric ˚C Load and cold fill on model Heavily soiled loads. On completion, switch ‘OFF’ mains button before selecting 40 3kg to 5.5kg 15-25 400rpm wash programme .
Button Selection T o selec t an optional wash f eature, press button and a colour ba nd will become visible. Press again t o cancel. Option Buttons Half Load Save money and time on smaller loads. ● Reduces the quantity of water used for rinsing . ● Not available with pr ogramme ‘ A ’ .
13 Spin only option... IMPORT ANT INFORMA TION: Before selecting a programme, ensure the ma ins button is in the ‘OFF’ position. T o selec t long spin, turn wash dial clockwise until pointer aligns with ( Fig 1). F or a shor t spin turn wash dial and align pointer to ( F ig 2).
The Dispenser Dr awer Choose a Suitable Detergent ● Hotpoint recommend the P ersil range of detergent products. ● Select ‘low suds’ automatic powder , designed specifically for aut oma tic washing machines or washer/dryers. ● F ollow manufacturer ’ s dosage recommendations.
15 T o obtain claimed energy label wash performance for a 60°C cotton wash, dispense powder detergent in a dosing ball, placed in an upright position in the centre of the wash load (F ig 5).
Removing and Cleaning the Dispenser Draw er & Compartments Note: It is advisable to clean the dispenser drawer regularly . Re-locate dispenser drawer and push firmly back into place. Clean dispenser drawer and internal fixed compartment and dr y thoroughly .
17 T roubleshooting ... If the appliance is still not working contact: Ser vice UK: 08709 066 066 Republic of Ireland:1850 302 200 you will be asked for the follo wing information:- ● Name, address .
18 Hotpoint appliances carry for the first 12 months a fully inclusive parts and labour guarantee plus FREE replacement parts for the first 5 years provided tha t they are fitted by our own Ser vice Engineer .
19 Fr om the moment your appliance is delivered , Hotpoint guarantees it f or five years. ● Hotpoint appliances carry a fully inclusive 12 months parts and labour guarantee plus FREE replacement parts for the first five years provided tha t they are fitted by our own Service Engineer (evidence will be required of date and place of purchase).
Key C ontac ts Ser vice UK: 08709 066 066 Republic of Ireland: 1850 302 200 Y ou will be asked to quote the Model Number and Serial Number, which can be found on the inside of the door .
デバイスHotpoint WM83の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hotpoint WM83をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHotpoint WM83の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hotpoint WM83の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hotpoint WM83で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hotpoint WM83を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHotpoint WM83の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hotpoint WM83に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHotpoint WM83デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。