HP (Hewlett-Packard)メーカー3C509B-TPの使用説明書/サービス説明書
ページ先へ移動 of 46
Etherlink IIIB ISA Network Interface Card (10BT) 3C509B-TP Installation Guide.
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 1 Connecting to a Netware 3.12 Server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 4 Select “CONFIGURE NIC,” and verify the resource settings listed above under the heading “Device Configuration.” 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1.
1 Connecting to a Netware 3.12 Server Windows for Workgroups 9 Select 16-bit LAN Drivers and hit the enter key. 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:NWCLIENT” and press enter.
1 Connecting to a Netware 3.12 Server Windows for Workgroups.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. • Vectra VL8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
1 Connecting to a Netware 3.12 Server Windows 95 SR2 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 2 Connecting to a Netware 4.11 Server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 6 Remove the 3COM cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. If you are using a Vectra VL8, go straight to step 7. If you are using a VL7 or VE7/VE8, finish the installation by using the instructions below.
2 Connecting to a Netware 4.11 Server Windows for Workgroups 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:NWCLIENT” and press enter.
2 Connecting to a Netware 4.11 Server Windows for Workgroups.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Vectra VL8 and VE7/VE8 Driver Name : W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
2 Connecting to a Netware 4.11 Server Windows 95 SR2 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.” 8 Double click on “Network” and select “Add.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11.
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. • Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97 • Vectra VL7 Driver Name: Elnk.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the 3Com Software driver diskette and reboot the machine. 8 Click on “Start” and point to “Settings”, then select the “Control Panel.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 an HP preloaded HDD, set the path to “C:MASTERSWIN95SYSTEMCABS”) 21 To complete the installation, select “Yes” to restart your computer.
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 If you are using a Vectra VE7/VE8, follow the instructions below to complete the installation. a If changes are required, save those changes and exit. b Remove the 3COM software driver diskette and reboot the machine.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 q At the "TCP/IP Configuration" screen, choose to use DHCP or enter your TCP information and click on "OK." (If you do not have the required information, contact your network administrator.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 19 Choose to install all applicable TCP/IP options and select “Continue.” (If you do not have the required information, contact your network administrator) 20 At the “Network Settings” dialog box, click on “OK.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0. Driver Name: Elnk3.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 6 If changes are required, save those changes and exit. 7 Remove the 3com cards driver diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0.
4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
4. Connecting to a Windows NT Server 4.0 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. Vectra VL8 and VE7/VE8 Driver Name: W95EL5X9.INF Size:16KB Date: 6/11/97.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 6 If changes are required, save those changes and exit. 7 Remove the 3Com Software driver diskette and reboot the machine. 8 Click on “Start” and point to “Settings”, then select the “Control Panel.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 “C:MASTERSWIN95SYSTEMCABS”) 22 To complete the installation, select “Yes” to restart your computer.
4 Connecting to a Windows NT Server 4.0 Windows 95 SR2.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 Windows NT Workstation Version 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 7 Remove the 3com software driver diskette and reboot the machine. 8 After windows loads, open the “Main” program group, double-click on “Control Panel” icon. 9 Double click on the “Network” icon and agree to install Windows NT Networking on your computer.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51 administrator) 23 At the “Domain/Workgroup Settings” Dialog Box, click on “OK” to accept the default “Workgroup” as your workgroup name.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver 5.0. Driver Name: Elnk3.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 6 If changes are required, save those changes and exit. 7 Remove the 3com cards driver diskette and reboot the machine. 8 Power on the machine and allow it to boot to Windows NT Workstation 4.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.
4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0.
.
V ersion Number 3Com 3c509 Rev .1.
デバイスHP (Hewlett-Packard) 3C509B-TPの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) 3C509B-TPをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) 3C509B-TPの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) 3C509B-TPの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) 3C509B-TPで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) 3C509B-TPを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) 3C509B-TPの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) 3C509B-TPに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) 3C509B-TPデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
