HP (Hewlett-Packard)メーカー3C905-TXの使用説明書/サービス説明書
ページ先へ移動 of 42
Fast Etherlink XL TX PCI Network Interface Card (10/100BT) 3C905-TX Installation Guide.
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Connecting to a Netware 3.12 server Windows for Workgroups Connecting to a Netware 3.12 server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.
Connecting to a Netware 3.12 server Windows for Workgroups adapter card into a PCI slot. 2 Power on the machine and allow it to boot to a DOS prompt. 3 Insert the 3COM drivers diskette and execute 3C90XCFG.EXE. 4 Select “CONFIGURE NIC” and verify the resource settings listed above under the heading “Device Configuration.
Connecting to a Netware 3.12 server Windows for Workgroups 8 Accept the default installation options by pressing “F10.” 9 At the “Customize Support for Windows” screen, press “F10.” 10 Select 32-bit LAN Drivers and hit the enter key. 11 Page down the Board Drivers list to “USER SPECIFIED 32 BIT DRIVER LIST” and hit enter.
Connecting to a Netware 3.12 server Windows 95 SR2 Connecting to a Netware 3.12 server Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.1. • File Name: OEMSETUP.INF Size: 41KB Date: 3/14/97 • Windows 95 SR2 media.
Connecting to a Netware 3.12 server Windows 95 SR2 adapter card into a PCI slot. 2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode. 3 Insert the 3COM drivers diskette (ver. 2.1 downloaded from 3COM’s Web site) and execute 3C90XCFG.EXE.
Connecting to a Netware 3.12 server Windows 95 SR2 and click on “Close.” (If you do not have a Computer name, Workgroup name and Computer description, contact your network administrator.) 18 At the “Insert Disk” notification, click on “OK.” 19 Set the path to your Windows 95 SR2 media and click on “OK.
Connecting to a Netware 4.1 server Windows for Workgroups Connecting to a Netware 4.1 server Windows for Workgroups Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.
Connecting to a Netware 4.1 server Windows for Workgroups adapter card into a PCI slot. 2 Power on the machine and allow it to boot to a DOS prompt. 3 Insert the 3COM drivers diskette and execute 3C90XCFG.EXE. 4 Select “CONFIGURE NIC” and verify the resource settings listed above under the heading “Device Configuration.
Connecting to a Netware 4.1 server Windows for Workgroups 8 Accept the default installation options by pressing “F10.” 9 At the “Customize Support for Windows” screen, press “F10.” 10 Select 32-bit LAN Drivers and hit the enter key. 11 Page down the Board Drivers list to “USER SPECIFIED 32 BIT DRIVER LIST” and hit enter.
Connecting to a Netware 4.1 server Windows 95 SR2 Connecting to a Netware 4.1 server Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.1. • File Name: OEMSETUP.INF Size: 41KB Date: 3/14/97 • Windows 95 SR2 media.
Connecting to a Netware 4.1 server Windows 95 SR2 Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C905 adapter card into a PCI slot. 2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode. 3 Insert the 3COM drivers diskette (ver.
Connecting to a Netware 4.1 server Windows 95 SR2 16 At the “Network” dialogue box, click on the “Identification” folder. 17 Enter your “Computer Name,” “Workgroup,” and “Computer Description” and click on “Close.
Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver.
Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 under the heading “Device Configuration.” 6 If changes are required, save those changes and exit. 7 Remove the 3COM Drivers diskette and reboot the machine. 8 After windows loads, open the “NETWORK” program group, and double- click on “Network Setup” icon.
Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 C:MASTERSDRIVERSLAN3C905DISK1MSLANMAN.DOSDRIVERS ETHERNETEL90X) 21 Finish the network card installation by clicking on “OK” in the “Network Setup” message.
Connecting to a Windows NT Server 3.51 Microsoft Windows 95 SR2 Connecting to a Windows NT Server 3.51 Microsoft Windows 95 SR2 Requirements • HP Vectra with Plug and Play enabled, running Windows 95 SR2. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.
Connecting to a Windows NT Server 3.51 Microsoft Windows 95 SR2 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM drivers disk 1, “Etherlink 3C905 Ethernet Drivers Ver. 2.1.” and execute “A:3C90XCFG.EXE.
Connecting to a Windows NT Server 3.51 Microsoft Windows 95 SR2 21 Highlight the “TCP/IP” network component and click on the “Properties” button.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 3.51 Connecting to a Windows NT Server 3.51 Windows NT Workstation 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C905 ethernet card and drivers disk ver.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 3.51 2 Connect network cable media to the 3COM 3C905 card. 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM software “3C905 Ethernet drivers disk ver 2.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 3.51 20 Click on the “OK” button in the “3Com DRMON SmartAgent PC Software” dialog box.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 adapter card into a PCI slot. 2 Connect network media to the 3COM 3C905 PCI card. 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM Etherlink 3C905 Ethernet card and drivers Disk 1 ver 2.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 18 Accept the default Network Protocol TCP/IP and click on any additional protocols, then click “Next.” (If you do not have the required Protocols information, contact your network administrator.
Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0 34 To complete the installation, select “Yes” to reboot your computer. c 905.bk : ch_8.
Connecting to a Windows NT Server 4.0 Windows for Workgroups ver. 3.11 Connecting to a Windows NT Server 4.0 Windows for Workgroups ver. 3.11 Requirements • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver.
Connecting to a Windows NT Server 4.0 Windows for Workgroups ver. 3.11 2 Connect network cable media to the 3COM 3C905 card. 3 Power on the machine and set Plug and Play in CMOS to off. 4 After booting, insert the 3COM’s drivers disk “Etherlink 3C905 Ethernet ver.
Connecting to a Windows NT Server 4.0 Windows for Workgroups ver. 3.11 21 Insert disk 2 and set “Install Driver” path to “A:MSLANMAN.DOSDRIVERSETHERNETEL90X” and click “OK” to complete file copying. (If you have an HP preloaded HDD, set the path to C:MASTERSDRIVERSLAN3C905DISK1MSLANMAN.
Connecting to a Windows NT Server 4.0 Windows 95 SR2 Connecting to a Windows NT Server 4.0 Windows 95 SR2 Requirements • HP Vectra with Plug and Play enabled, running Windows 95 SR2. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.1. • Vectra VL8 Driver Name: OEMSETUP.
Connecting to a Windows NT Server 4.0 Windows 95 SR2 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM drivers disk 1, “Etherlink 3C905 Ethernet Drivers Ver.
Connecting to a Windows NT Server 4.0 Windows 95 SR2 21 Highlight the “TCP/IP” network component and click on the “Properties” button. 22 If you know your TCP/IP settings, enter them in the “TCP/IP Properties” dialog box, otherwise leave the IP address choice checked “Obtain an IP address automatically”, and click “OK” .
Connecting to a Windows NT Server 4.0 Windows NT Workstation Ver. 3.51 Connecting to a Windows NT Server 4.0 Windows NT Workstation Ver. 3.51 Requirements • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. • 3COM Etherlink 3C905 ethernet card and drivers disk ver.
Connecting to a Windows NT Server 4.0 Windows NT Workstation Ver. 3.51 2 Connect network cable media to the 3COM 3C905 card. 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM software “3C905 Ethernet drivers disk ver 2.
Connecting to a Windows NT Server 4.0 Windows NT Workstation Ver. 3.51 20 Click on the “OK” button in the “3Com DRMON SmartAgent PC Software” dialog box.
Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 Requirements • HP Vectra with Windows NT Workstation 4.0 Service Pack 3. • 3COM Etherlink 3C905 Ethernet card and drivers disk ver 2.
Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 adapter card into a PCI slot. 2 Connect network media to the 3COM 3C905 PCI card. 3 Insert a DOS bootable diskette and power on the machine. 4 After booting, insert the 3COM Etherlink 3C905 Ethernet card and drivers Disk 1 ver 2.
Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 18 Accept the default Network Protocol TCP/IP and click on any additional protocols, then click “Next.” (If you do not have the required Protocols information, contact your network administrator.
Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0 34 To complete the installation, select “Yes” to reboot your computer. c 905.bk : ch_12.
c 905.bk : bcover.fb4 Page xxxvii Thursday, October 22, 1998 9:51 AM.
V ersion Number 3COM 905 Rev .1 c 905.bk : bcover.fb4 Page xxxviii Thursday, October 22, 1998 9:51 AM.
デバイスHP (Hewlett-Packard) 3C905-TXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) 3C905-TXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) 3C905-TXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) 3C905-TXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) 3C905-TXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) 3C905-TXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) 3C905-TXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) 3C905-TXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) 3C905-TXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
