HP (Hewlett-Packard)メーカーg6-1b60usの使用説明書/サービス説明書
ページ先へ移動 of 53
Getting Started HP Notebook.
© Copyright 2011 Hewlett-Packa rd Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered tr ademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor.
Safety warning notice WARNING! To reduce the possibility of heat-related inju ries or of ove rheating th e computer, do not place the compu ter directly on your lap or o bstruct the computer air ven ts.
iv Safety warning no tice.
Table of contents 1 Welcome ........ ....... .......... ......... ........ .......... ........ ......... ......... ........ ......... .......... ....... .... ............. ....... ......... ........ . 1 Finding information ................... ........
Scrolling ......... ............ .................... .......................... ................... ............ .......... ......... ........ 23 Pinching /Zooming . ......... ......... .......... .......... ......... .......... ......... ......... .
1W e l c o m e ● Finding information After you set up and register the compu ter, it is important to take the following steps: ● Connect to the Internet — Set up your wired or wi reless network so that you can connect to the Internet. For more information, refer to Finding in formation on page 2 .
Finding information The computer comes with several resour ces to help you perform various tasks. Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components Getting Started To access this guide: Select Start > Help and Support > User Guides .
Resources For information about Safety & Comfort Guide To access this guide: Select Start > Help and Support > User Guides . – or – Select Start > All Programs > HP > HP Documentation . – or – Go to http://www.hp.com/ ergo .
2 Getting to know your computer ● Top ● Front ● Right side ● Left side ● Display ● Bottom Top TouchPad Component Description (1) TouchPad light ● Off: The TouchPad is on. ● Amber: The TouchPad is off. (2) TouchPad button Turns the TouchPad on and off.
Component Description (3) Left TouchPad button Functions like the left button on an e xternal mouse. (4) TouchPad zone Moves the pointer and selects or activate s items on the screen. (5) Right TouchPad button Functions like the right button on a n external mouse.
Buttons Component Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows logo key Displays the Windows Start menu.
Front Component Description Speakers (2) Produce sound Right side Component Description (1) Optical drive Reads and writes (selec t models only) to an optical disc. (2) Optical drive light Green: The opt ical drive is being accesse d. (3) USB port Connects an optional USB device.
Left side Component Description (1) External monitor port Connects an ex ternal VGA monitor or projector. (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent over heating.
Component Description (9) Hard drive light ● Whit e: The hard drive is being accessed. (10) Power light ● White: The computer is on. ● Blinking white: The computer is in Sleep mode.
Display Component Description (1) WLAN antennas (2)* Send and receive wirele ss signals to comm unicate with wireless local area networks (W LANs) (2) Webcam light On: The webcam is in use. (3) Webcam Records video and captures still photographs To use the webcam, select Start > All Programs > Cyberlink YouCam .
Bottom Component Description (1) Battery bay Holds the battery (2) Vents (5) Enable airflow to coo l internal comp onents NOTE: The computer fan starts up auto matically to cool internal components and prevent overhe ating. It is normal for the internal fan to cycle on and off during routine operation.
3N e t w o r k i n g ● Using an Intern et service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and so ftware features vary d epending on comp uter model and your location.
Using an Internet service provider (ISP) Before yo u can connect to the Internet, you must estab lish an ISP account. Con tact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network ca ble to connect your wireless computer to th e modem, and test the Intern et service.
Connecting to an existing WLAN 1. Turn on th e compute r. 2. Be sure that the WL AN device is on. 3. Click the network icon in the notificat ion area, at the far right of the taskb ar. 4. Select a network to conn ect to. 5. Click Connect . 6. If requir ed, ente r the se curity k ey.
Configuring a wireless router For help in setting up a WLAN, refer to the informat ion provided by your ro uter manufacture r or your ISP. The Windows operating system also provides tools to help you set up a new wireless network.
4 Keyboard and pointing devices ● Using the keyboa rd ● Using pointing devices ● Using TouchPad gestures 17.
Using the keyboard Using the action keys Action keys are customized actions that are a ssigned to specific keys at the top of the ke yboard. The icons on the f1 through f12 keys represent the action key functions . To use an action key, press and ho ld this key to activate the assigned fu nction.
Icon Key Description f9 Decreases speaker volume incrementally when you hold down this key f10 Increases speaker volume increment ally when you hold down this key f11 Mutes or restores speaker sound f12 Turns the wireless feature on or off NOTE: This action key does not establish a wi reless connection.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased sep arately) by connecting it to one of the USB ports on the computer .
Turning the Touc hPad off and on To turn the Tou chPad off and on, quickly do uble-tap the Tou chPad button. NOTE: The TouchPad light is o ff when the TouchPad is on. Navigating To move the pointer, slid e one finger across the Touc hPad in the direction you want the pointer to go.
Selecting Use the left and right Touch Pad buttons like the corresp onding buttons on an external mouse. Using TouchPad gestures The TouchPad sup ports a variety of gestures. To use TouchPad gestures, place two fin gers on the TouchPad at the same time.
Scrolling Scrolling is useful for movi ng up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPa d, an d then dr ag them acro ss the Touch Pad in an up, d own, left, or right motion. NOTE: Scrolling speed is co ntrolled by finger speed.
Rotating Rotating allows you to rotate it ems such as photos. T o rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger a round th e an chored finger in a sweeping motion, mo ving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock.
5 Maintenance ● Inserting or removing th e battery ● Replacing or upgrad ing the hard drive ● Adding or replacing mem ory modules ● Updating programs an d drivers ● Routine ca re Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Refe rence Guide .
2. Remove the battery fr om the bat tery bay (2) . 26 Chapter 5 Mainte nance.
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do no t remove the hard drive while the computer is on, in th e Sleep state, or in Hibern ation.
8. Disconnect the hard drive ca ble from the system board (1) , and then lift the ha rd drive away from the computer (2) . Installing a hard drive To install a hard driv e, follow these steps: 1. Insert the hard d rive into the ha rd drive bay (1) , a nd then connect the hard drive cable to the system board (2) .
4. Tighten the service cover screws (3) . 5. Replace the battery. 6. Turn the computer right-side up. 7. Reconnect external po wer to the computer. 8. Reconnect any external devices. Adding or replacing memory modules The computer has o ne memory module compartment, wh ich is located on the bottom of the computer.
CAUTION: To prevent information loss or an unresponsive system: Shut down the compu ter before a dding or repl acing memory modules. Do not remove a memory module while the computer is on, in Sleep mode, or in Hiber nation mode.
b. Grasp th e edge of th e memory module (2) , and then ge ntly pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch th e components on the memory modul e.
c. Gently press the memory mo dule (3) down, applying pr essure to both the left an d right edges of the memo ry module, until the retenti on clips snap i nto place. CAUTION: To prevent damage to the memo ry module, be sure that you do not bend th e memory module.
Updating programs and drivers HP recommends that you up date your prog rams and driver s on a regular basis with the la test versions. Go to http://www.hp.com/ support to download the l atest versions. You can also register to receive automatic update n otifications when they become a vailable.
6 Backup and recovery ● Restore ● Creating restore media ● Performing a system restore ● Backing up and re covering your infor mation Your computer includes t ools provided by the operating system and HP to help you safeguard your information and restore it if ever needed.
Restore In the event of hard drive failure, to restore your system to its factory image you will need a set of recovery discs or a recovery flash drive that you can create using HP Recovery Manager. HP recommends that you use this softwa re to create either a set of re covery discs or a recovery flash drive immediately afte r software setu p.
Performing a system restore HP Recovery Manager software a llows you to repair or re store the computer to its original factory state. HP Recovery Manager works from recovery di scs, a reco very flash drive, or from a dedicated recovery partition (se lect models only) o n the hard drive.
Restoring using the restor e media 1. If possible, bac k up all personal files. 2. Insert the first recovery disc into the optical drive on your computer or an optional external optical drive, and then restart the co mputer. – or – Insert th e recov ery flash d rive into a USB por t on your computer, and th en restart the computer.
Changing the computer boot order To change the boot or der for recovery discs: 1. Restart the computer. 2. Press esc while the computer is re starting, and then press f9 fo r boot options. 3. Select Internal CD/DVD ROM Drive from the boot option s window.
To create a scree n shot: 1. Display the screen you want to save. 2. Copy the screen image: To copy only the ac tive window, p ress alt + fn + prt sc . To copy the entire screen, press fn + prt sc . 3. Open a word-processing document, and th en select Edit > Paste .
Using Windows system restore points A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recove r back to that po int if you want to reverse subsequent changes.
7 Customer support ● Contacting customer suppo rt ● Labels 41.
Contacting customer support If the information provided in this user guide, in the HP Notebook Referen ce Guide , or in Help and Support does not address your questions, you can contact HP Custo mer Support at: http://www.
Labels The labels that are a ffixed to the compute r provide info rmation that you may need whe n troubleshooting system problems o r trave ling in ternationally with the computer: ● Service tag—P.
8 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpfu l if you plan to travel internationally with the computer. The computer op erates on DC power, whi ch can be supplied by an AC or a DC power source.
Operating environment Factor Metric U.S. Temperature Operating (writing to optical disc) 5°C to 35°C 41°F to 95°F Nonoperating -20°C to 60°C -4°F to 140°F Relative humidity (noncondensing) Ope.
Index A AC adapter light, identifying 8 action keys adjusting volume 19 decrease screen brightness 18 description 18 increase screen brightness 18 muting speaker soun d 19 switching screen image 18 wi.
M memory module inserting 31 removing 30 replacing 29 memory module compartment cover removing 30 replacing 32 microphone (audio-in) jack, identifying 9 Microsoft Certificat e of Authenti city label 4.
デバイスHP (Hewlett-Packard) g6-1b60usの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) g6-1b60usをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) g6-1b60usの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) g6-1b60usの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) g6-1b60usで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) g6-1b60usを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) g6-1b60usの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) g6-1b60usに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) g6-1b60usデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
