HP (Hewlett-Packard)メーカーmx704の使用説明書/サービス説明書
ページ先へ移動 of 37
Reference Guide CRT Monitors 5500, v72, mx704, 7500, 7550, 9500 Document Part Number: 346224-002 January 2004 This guide provides information on setting up the monitor, installing drivers, using the on- screen display menu, troubleshooting, regulatory notices, and technical specifications.
© Copyright 2004 Hewlett-Packard Development Company, L.P. The information contained here in is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U.S. and other countries. Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in the U.
Contents 1 Introduction Kit Contents ...................................................................... 1–1 2 Safety and Maintenance Guidelines Safety Guidelines.............................................................. 2–1 Power Requirements .
Contents Monitor Messages .......................................................... 4–10 No Signal Message .................................................. 4–10 Out of Frequency Range Message ........................... 4–11 Using the Energy Saver Mode .
1 Introduction Your microprocessor-based, digita lly controlled color monitor is a high-performance and easy-to-use product. It employs the latest on-screen menu technology.
2 Safety and Maintenance Guidelines Safety Guidelines Power Requirements A power cord is included with your monitor. If another cord is used, use only a power source a nd connection appropriate for this monitor.
Safety and Maintenance Guidelines CAUTION: For the protection of your monitor, as well as your computer, connect all power cords for your computer and its peripheral devi ces (such as a monitor, printer, scanner) to some form of surge protection device such as a power strip or Uninterruptible Power Supply (UPS).
Safety and Maintenance Guidelines Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of th e products connected to the cord does not exceed the rating of the cord.
Safety and Maintenance Guidelines Do not place the monitor face down. Damage could result to the front panel controls or the monitor screen. Removing the Monitor Base In the event that you need to disassemble the base from the monitor, follow these instructions: 1.
3 Installation Attaching the Monitor Base On some monitors, the base must be attached prior to setting up the monitor. To attach the base: 1. Align the hooks on the base with the sockets on the bottom of the monitor and attach the base.
Installation 2. Push the base toward the front of the monitor until it stops. Setting Up the Monitor Before setting up the monitor, place it in a convenient, well- ventilated location near your computer. 1. Turn off the power to your computer and other peripheral devices.
Installation 3. Connect the power cord 2 to the back of the monitor, then connect the power cord to a power outlet. 4. Power on your computer and monitor. If your monitor fails to function properly, refer to Appendix A, “Troubleshooting.” 5. If necessary, adjust the front panel monitor controls according to your personal preference.
Installation Connecting the Speakers (Available with Select Models) To install the JBL or Harman/Kardon speakers: 1. Place the control speaker 1 and the other speaker 2 on either side of the monitor.
Installation You can attach the speakers to the monitor or place them on an even surface next to the monitor. To attach the JBL speakers to the monitor, see the following section, “Attaching the JBL Speakers to the Monitor.” Attaching the JBL Speakers to the Monitor To attach the JBL speakers to the sides of your monitor: 1.
Installation Using the JBL Speaker Security Lock The JBL speakers can be locked to the sides of the monitor. To use the Speaker Security Lock: 1. Grasp the front cloth-covered grill firmly at the sides and remove from the speaker, then lo cate the security lock screw, which can be found in the top inner corner of the speaker.
Installation Connecting Portable Output Devices to the JBL Speakers You can use the JBL speakers to listen to portable output devices such as MP3 players or CD players. To connect the device to the speakers: 1.Plug the cable (not included) from the output device into the Line In connector on the front of the speaker.
A Troubleshooting Solving Common Problems The following table lists possible problems, the possible cause of each problem, and the recommended solutions. Problem Possible Cause Solution Screen is blank. Power cord is disconnected. Connect the power cord.
Troubleshooting Problem Possible Cause Solution Monitor may have been moved or inadvertently bumped. Press the SELECT button to access the On-Screen Display. Select Degauss to activate. Hewlett-Packard suggests you not degauss more than once within a 30-minute period of time.
Troubleshooting Problem Possible Cause Solution “No Signal” is displayed on screen. Monitor video cable is disconnected. Connect the 15-pin monitor video cable to the computer. Be sure that the computer power is on. “Out of Frequency” is displayed on screen.
Troubleshooting Using the Worldwide Web Before contacting customer serv ices, refer to the support Web site at: http://www.hp.com/support. Preparing to Call Technical Support If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical support.
B Technical Specifications All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP’s component manufacturers’ typical level specifications for performance and actual performance may vary either higher or lower.
Technical Specifications ( Continued) Max Pixel Clock 70 MHz Max. Input Signal Video RGB Analog Sync. TTL Separate Video Cable 15-pin D-sub connector Power Input Voltage Frequency 100 to 240V AC 50 +3 to 60 +3 Hz Inrush Current 30 amps @ 120V 60 amps @ 220V Power Consumption 80 W (Max.
Technical Specifications v72/17” Series Monitor Screen Size 17” (43 cm) visual diagonal Viewable screen size 16” (40.6 cm) Dot Pitch 0.28 mm (Diagonal) Display Area Default 234 x 312 (mm) typica.
Technical Specifications Weight 38 lb Max. 17 kg Max. Operating Temperature 50o F to 95o F 10o C to 35o C Storage Temperature -22o F to 140o F -30o C to 60o C Humidity 20% to 80% (non-condensing) Altitude Up to 10,000 ft.
Technical Specifications mx704/17” Series Monitor Screen Size 17” (43 cm) visual diagonal Viewable screen size 16” (40.6 cm) Anti-Glare Coating Dot Pitch 0.
Technical Specifications Weight 42 lb Max. 19 kg Max. Operating Temperature 50o F to 95o F 10o C to 35o C Storage Temperature -22o F to 140o F -30o C to 60o C Humidity 20% to 80% (non-condensing) Altitude Up to 10,000 ft.
Technical Specifications 7500/17” Series Monitor Screen Size 17” (43 cm) visual diagonal Viewable screen size 16” (40.6 cm) Dot Pitch 0.28 mm (Diagonal) Display Area Default 234 x 312 (mm) typic.
Technical Specifications Weight 38 lb Max. 17 kg Max. Operating Temperature 50o F to 95o F 10o C to 35o C Storage Temperature -22o F to 140o F -30o C to 60o C Humidity 20% to 80% (non-condensing) Altitude Up to 10,000 ft.
Technical Specifications 7550/17” Flat CRT Monitor Screen Size 17” (43 cm) visual diagonal Viewable screen size 16” (40.6 cm) Anti-Glare Coating Dot Pitch 0.
Technical Specifications Weight 42 lb Max. 19 kg Max. Operating Temperature 50o F to 95o F 10o C to 35o C Storage Temperature -22o F to 140o F -30o C to 60o C Humidity 20% to 80% (non-cond ensing) Altitude Up to 10,000 ft.
Technical Specifications 9500/19” Series Monitor Screen Size 19” (48 cm) visual diagonal Viewable screen size 18” (46 cm) Anti-Glare Coating Dot Pitch 0.
Technical Specifications Dimension (W x H x D) Unpacked w/attached base 17.9 x 18.5 x 18.7 inches (maximum) 455 x 470 x 475 mm (maximum) Weight 44 lb Max. 20 kg Max. Operating Temperature 50o F to 95o F 10o C to 35o C Storage Temperature -22o F to 140o F -30o C to 60o C Humidity 20% to 80% (non-condensing) Altitude Up to 10,000 ft.
C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Agency Regulatory Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules.
Agency Regulatory Notices Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Caus ing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Agency Regulatory Notices Japanese Notice Korean Notice EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Hewlett Packard Company has determined that this product meets the Energy Star guidelines for energy efficiency.
Agency Regulatory Notices The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the country where you purchased the equipment. If you need to obtain a power cord for a different country, you should purchase a power cord that is approved for use in that country.
デバイスHP (Hewlett-Packard) mx704の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) mx704をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) mx704の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) mx704の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) mx704で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) mx704を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) mx704の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) mx704に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) mx704デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
