HTCメーカーLZC5227 / 965879701の使用説明書/サービス説明書
ページ先へ移動 of 76
English Operator Manual LZC5225 / 965879601 LZC5227 / 965879701 LZC6130 / 965879801 LZ30 / 968999776 Please read the operator ’s manual carefully and make sure you understand the instructions before using the machine.
©2008 HTC. All rights reserved. Beatrice, NE. Printed in U.S.A. In order to implement improvements, specications and designs can be altered without prior notication. Note that no legal demands can be placed based on the information contained in these instructions.
CONTENTS INTRODUCTION ...................................................... 5 Driving and T ransport on Public Roads .............. 5 T owing ................................................................ 5 Operating ...............................
English - 4 W ARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower .
Husqvarna - 5 INTRODUCTION Congratulations Thank you for purchasing a Husqvarna ride-on mower . This machine is built for superior efciency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
6 - Husqvarna INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer .
SYMBOLS AND DECALS Husqvarna - 7 These symbols are found on the machine and in the operator ’s manual. Study them carefully so that you know what they mean. Used in this publication to notify the reader of a risk of personal injury or death , particularly if the reader should neglect to follow instructions given in the manual.
SYMBOLS AND DECALS 8 - Husqvarna Read Shut off engine and Keep a safe Use on slopes No passengers Operator ’s remove key before distance from no greater Manual performing any the machine than 10° m.
SAFETY Husqvarna - 9 Safety Instructions These instructions are for your safety . Read them carefully . IMPORT ANT : THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OBJECTS. F AILURE TO OBSER VE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
SAFETY 10 - Husqvarna 801 1-520 Never take passengers W atch for trafc when operating near or crossing • roadways. Use extra care when loading or unloading the • machine into a trailer or truck. Always wear eye protection when operating • machine.
SAFETY Husqvarna - 11 Personal Safety Equipment 801 1-670a Personal protective equipment 6003-004 Mow up and down, not side to side Make sure that you have rst aid equipment close • at hand when using the machine. Never use the machine when barefoot.
SAFETY 12 - Husqvarna 801 1-509 Be extra cautious when driving on slopes 801 1-517 Never allow children to operate the machine 801 1-518 Keep children away from work area Children T ragic accidents can occur if the operator is not alert to the presence of children.
SAFETY Husqvarna - 13 Safe Handling of Gasoline T o avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely ammable and the vapors are explosive. Extinguish all cigarettes, cigars, pipes, and other • sources of ignition.
SAFETY 14 - Husqvarna 801 1-515 Never drive the machine in an enclosed space General Maintenance Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the • equipment is in safe working condition. Never tamper with safety devices.
SAFETY Husqvarna - 15 Sparking can occur when working with the battery • and the heavy cables of the starter circuit. This can cause battery explosion, re or eye injury . Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery .
SAFETY 16 - Husqvarna IMPORT ANT INFORMA TION The parking brake is not sufcient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over .
SAFETY Husqvarna - 17 W ARNING! This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine's system is equipped with a spark arrester meeting applicable local or state laws (if any).
CONTROLS 18 - Husqvarna This operator ’s manual describes the Husqvarna Zero T urn Rider . The rider is tted with either a Kohler or Kawasaki four-stroke overhead valve engine developing 25-30 horse power*. T ransmission from the engine is made via two belt- Control Locations 1.
CONTROLS Husqvarna - 19 801 1-788 Steering controls Motion Control Levers The machine’s speed and direction are continuously variable using the two steering controls.
CONTROLS 20 - Husqvarna Hour meter The hour meter displays the total operating time. It will ash CHG OIL (Change Oil) at 50 hour intervals. The ash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically .
CONTROLS Husqvarna - 21 Fuses The fuses are located in a holder to the left of the hydraulic tank. They are at pin fuses of the same type used in automobiles. There are three fuses as well as a socket for one spare fuse. Fuse ratings and functions: 20 A, Primary fuse.
CONTROLS 22 - Husqvarna IMPORT ANT INFORMA TION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.
CONTROLS Husqvarna - 23 Seat Lock Under the rear section of the seat is a lock device to lock the seat into a folded position. The seat has a linked xture at the front edge and can be folded forward when the lock is pushed. 801 1-440 Seat lock Fuel shut off valve The fuel shut off valve is located at the right rear of the seat.
CONTROLS 24 - Husqvarna Mower Deck Lifting Lever The lifting lever is used to place the mower deck in the transport position or one of the 17 different cutting height positions.
CONTROLS Husqvarna - 25 IMPORT ANT INFORMA TION T o obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar). Cutting height lift pedal On some models, there is a deck assist lift pedal to aid in maneuvering the deck lift.
OPERA TION 26 - Husqvarna Read the “Safety Instructions” section and the following pages if you are unfamiliar with the machine. T raining Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities.
OPERA TION Husqvarna - 27 801 1-527 Start conditions 801 1-753 Raise the mower deck Starting the Engine Sit on the seat. 1. Raise the mower deck by pulling the lifting 2. lever backward to the locked position (transport position). Activate the parking brake.
OPERA TION 28 - Husqvarna 801 1-510 Depress the control for disengaging the mower deck 801 1-526 Steering controls in the outward, locked neutral position 801 1-509 Set the throttle Disengage the mower blades by depressing 4. the blade switch. Move the steering controls outward to the 5.
OPERA TION Husqvarna - 29 801 1-742 T urn to the start position 801 1-508 Set the choke control Open the valve for the selected fuel tank. 8. 801 1-506 Open the fuel valve If the engine is cold, the choke control should 7. be pulled outward to the choke position.
OPERA TION 30 - Husqvarna When the engine starts, immediately release 10. the ignition key back to the run position. IMPORT ANT INFORMA TION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait about 10 seconds before retrying.
OPERA TION Husqvarna - 31 Weak Battery If “jumper cables” are used for emergency starting, follow this procedure: Jumper Cables Connect each end of the RED cable to the • POSITIVE (+) terminal on each battery , taking care not to short against chassis.
OPERA TION 32 - Husqvarna IMPORT ANT INFORMA TION The mower deck’ s gauge wheels should be evenly adjusted. 801 1-561 Select the cutting height Running Release the parking brake by moving the lever 1. downward. Y our mower is equipped with an operator presence system.
OPERA TION Husqvarna - 33 Operating on Hills Read the Safety Instructions “Driving on Slopes” in the “Safety Instructions”. The slowest speed possible should be used • before starting up or down hills. Avoid stopping or changing speed on hills.
OPERA TION 34 - Husqvarna 801 1-603a Mowing pattern Mowing Tips Observe and ag rocks and other xed objects to • avoid collisions. Begin with a high cutting height and reduce it until • the desired mowing result is attained.
OPERA TION Husqvarna - 35 801 1-507 V ent screws on the hydraulic pump Moving by Hand When pushing or pulling the mower with the engine turned off,the vent screws on both hydraulic pumps must be opened ¼ - ½ turn.
MAINTENANCE 36 - Husqvarna 1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. 2) In dusty conditions, cleaning and replacement are required more often. 3) Performed by authorized service workshop.
MAINTENANCE Husqvarna - 37 Check/adjust throttle cable ● Check the condition of belts, belt pulleys ● ● Change the engine oil 1) ● ● Replace the engine oil lter ● ● Clean/replace the .
MAINTENANCE 38 - Husqvarna 1 2 801 1-466 1. T erminal guard 2. Battery hold downs Battery installation Battery Y our mower is equipped with a maintenance free battery and does not need servicing. However , periodic charging of the battery with an automotive type battery charger will extend its life.
MAINTENANCE Husqvarna - 39 Ignition System The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. For recommended spark plugs, see T echnical 1. Data. Remove the ignition cable boot and clean 2. around the spark plug.
MAINTENANCE 40 - Husqvarna Engine Cooling Air Intake Check that the engine’s cooling air intake is free from leaves, grass, and dirt. If the cooling air intake is clogged, engine cooling deteriorates, which can lead to engine damage.
MAINTENANCE Husqvarna - 41 Air Filter If the engine seems weak or runs unevenly , the air lter may be clogged. If running with a dirty air lter , the spark plugs can become fouled. For this reason, it is important to replace the air lter regularly (see the heading Maintenance Schedule for the proper service interval).
MAINTENANCE 42 - Husqvarna IMPORT ANT INFORMA TION The end cover must be installed with the rubber valve pointing downwards or the rubber valve will not function. Pull the main lter (outer) lter out. 1. Remove the inner lter . 2. Clean inside the lter housing, cover housing 3.
MAINTENANCE Husqvarna - 43 Fuel Filter Replace the line-mounted fuel lter every 100 hours (once per season) or more often if it becomes clogged. Move the hose clamps away from the lter . 1. Use at-nosed pliers. Pull the lter loose from the hose ends.
MAINTENANCE 44 - Husqvarna Checking the V -belts Check every 100 hours of operation. Check for severe cracking and large nicks. NOTE: The belt will show some small cracks in normal operation. The belts are not adjustable. Replace belts if they begin to slip from wear .
MAINTENANCE Husqvarna - 45 Pump belt Check belt every 100 hours for excessive wear . T o replace belt. Relieve tension on the deck belt and remove deck belt from clutch. See “Deck belt” section. Loosen bolt on the clutch tie down and rotate out of the way .
MAINTENANCE 46 - Husqvarna Cutter Blades T o attain the best mowing effect, it is important that the blades are well sharpened and not damaged. Bent or cracked blades or blades with large nicks should be replaced. Damaged blades should be replaced when hitting obstacles that result in a breakdown.
MAINTENANCE Husqvarna - 47 Adjusting the Mower Deck 801 1-601-1 1. Front eyebolt 2. Front locknut 3. Rear locknut 4. Rear eyebolt Leveling the mower deck Leveling Position the mower on a level, preferably 1. concrete, surface. Check the pressure in all four tires.
MAINTENANCE 48 - Husqvarna Cleaning Regular cleaning and washing, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the dirt sticks. Do not spray water on the top of the mower deck.
LUBRICA TION Husqvarna - 49 Lubrication Schedule General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be lled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.
LUBRICA TION 50 - Husqvarna Lubricating the Cables If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Ret the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly .
LUBRICA TION Husqvarna - 51 Engine Oil Changing the Engine Oil IMPORT ANT INFORMA TION Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.
LUBRICA TION 52 - Husqvarna Checking Oil Level 801 1-471 Oil dipstick 8009-159 Level marking The importance of checking and maintaining the proper oil level in the crankcase cannot be overemphasized. Check oil before each use as follows: Make sure the engine is stopped, level, and 1.
LUBRICA TION Husqvarna - 53 801 1-046 Viscosity grades table Oil Recommendations Using the proper type and weight of oil in the crankcase is extremely important. So is checking oil daily and changing oil regularly . Failure to use the correct oil, or using dirty oil, causes premature engine wear and failure.
LUBRICA TION 54 - Husqvarna Throttle and Choke Cables, Lever Bearings Lubricate the cable ends by the carburetor with the oil can. Move the controls to the end points and lubricate again. The throttle cable is also lubricated by the control when the control console is removed.
LUBRICA TION Husqvarna - 55 Steering Control Shafts T ip the driver ’s seat. Lubricate with a grease gun, one zerk for each steering control shaft, until the grease is forced out. Use only good quality molybdenum disulphide grease. Grease from well-known brand names (petrochemical companies, etc.
56 - Husqvarna TROUBLESHOOTING GUIDE Problem Cause The engine will not start. • The blade switch is engaged. • The steering controls are not locked in the neutral position. • The driver is not sitting in the driver’s seat. • The parking brake is not activated.
Husqvarna - 57 TROUBLESHOOTING GUIDE Problem Cause The engine seems weak. • Clogged air lter . • Fouled spark plugs. • Carburetor incorrectly adjusted. The engine overheats. • Clogged air intake or cooling ns. • Engine overloaded. • Poor ventilation around engine.
58 - Husqvarna ST ORAGE Winter Storage At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.
Husqvarna - 59 WIRING DIAGRAM B S A1 A2 L M G 20 AMP 7.5 AMP ELECTRIC CLUTCH ACCESSORY OUTLET HOURMETER SOLENOID PTO SWITCH B S A1 A2 L M G B S A1 A2 L M G B S A1 A2 L M G B S A1 A2 L M G ENGINE GROUN.
60 - Husqvarna TECHNICAL DA T A LZC5225 / 965879601 LZC5227 / 965879701 Engine Manufacturer Kawasaki Kohler T ype FH721V CV740S Power 25 hp* / 18.4 kW 27hp* / 22.4kW Lubrication Pressure with oil lter Pressure with oil lter Oil capacity excluding lter 1.
Husqvarna - 61 TECHNICAL DA T A LZC5225 / 965879601 LZC5227 / 965879701 Frame Cutting Width 52" / 132 cm 52" / 132 cm Cutting Height 1½ - 6" / 3.
62 - Husqvarna TECHNICAL DA T A LZC6130 / 965879801 LZ30 / 968999776 Engine Manufacturer Kohler Kohler T ype CV747S CV747S Power 30hp* / 22.4kW 30hp* / 22.4kW Lubrication Pressure with oil lter Pressure with oil lter Oil capacity excluding lter 1.
Husqvarna - 63 TECHNICAL DA T A LZC6130 / 965879801 LZ30 / 968999776 Frame Cutting Width 61" / 155 cm Cutting Height 1½ - 6" / 3.8 - 15.2 cm Uncut Circle 0 Number of Blades 3 Blade Length 2.
64 - Husqvarna TECHNICAL DA T A Accessories Collection system Engine crankshaft bolt 50 ft/lb (67 Nm) Deck pulley bolts 150 ft/lb (203 Nm) Lug nuts 75 ft/lb (100 Nm) Blade bolt 90 ft/lb (122 Nm) Stand.
Husqvarna - 65 CONFORMITY CERTIFICA TES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulll the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.
66 - Husqvarna W ARRANTY All Husqvarna products can be registered online at www .usa.husqvarna.com quickly and easily regardless of their model year . Click the Support tab, click on the Online Product Registration link and ll out the electronic form and submit.
Husqvarna - 67 SER VICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service 1. Charge the battery . 2. Adjust the tire pressure of all wheels to 15 PSI (1 bar). 3. Mount the steering controls in the normal position. 4. Connect the contact box to the cable for the seat’s safety switch.
68 - Husqvarna SER VICE JOURNAL Action Date, mtr reading, stamp, sign After the First 5-8 Hours 1. Change engine oil..
Husqvarna - 69 SER VICE JOURNAL Action Date, mtr reading, stamp, sign 25-Hour Service 1. Check the fuel pump’s air lter . 2. Sharpen/Replace mower blades if required. 3. Check the tire pressures. 4. Check battery with cables. 5. Lubricate according to lubrication chart.
70 - Husqvarna SER VICE JOURNAL Action Date, mtr reading, stamp, sign 50-Hour Service 1. Perform the 25-hour service. 2. Clean/replace the air cleaner ’s lter cartridge (paper lter) (shorter intervals for dusty operating conditions). 3. Change engine oil.
Husqvarna - 71 SER VICE JOURNAL Action Date, mtr reading, stamp, sign 100-Hour Service 1. Perform the 25-hour service. 2. Perform the 50-hour service. 3. Change the engine oil lter . 4. Clean/replace the spark plugs. 5. Replace the fuel lter . 6.
72 - Husqvarna SER VICE JOURNAL Action Date, mtr reading, stamp, sign 300-Hour Service 1. Inspect the machine. Come to agreement with the customer as to which additional work is to be carried out. 2. Perform the 25-hour service. 3. Perform the 50-hour service.
Husqvarna - 73 SER VICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Y ear 1. Clean the engine’s cooling air intake (25 hours). 2. Replace the air cleaner ’s pre-lter (foam) (300 hours). 3. Replace the air lter ’s paper cartridge.
74 - Husqvarna SER VICE JOURNAL Action Date, mtr reading, stamp, sign.
.
P/N 1 15 138927 R01 06/01/09.
デバイスHTC LZC5227 / 965879701の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
HTC LZC5227 / 965879701をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHTC LZC5227 / 965879701の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HTC LZC5227 / 965879701の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HTC LZC5227 / 965879701で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HTC LZC5227 / 965879701を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHTC LZC5227 / 965879701の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HTC LZC5227 / 965879701に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHTC LZC5227 / 965879701デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。