HubbellメーカーDiesel Engine Fire Pump Controller LX3000の使用説明書/サービス説明書
ページ先へ移動 of 17
Page 1 of 17 Hubbell Industrial Controls, Inc. A subsidiary of Hubbell Incorporated 4301 Cheyenne Dr. Archdale, NC 27263 Telephone (336) 434-2800 FAX (336) 434-2803 Instruction Manual Model LX3000 Diesel Engine Fire Pump Controller Publication No.
Instruction Manual LX3000 Diesel Fire Pump Controller Introduction Model LX3000 engine controllers, automatically control th e operation of diesel engine driven centrifugal fire pumps. Installation 1. Consult the Controller nameplate to verify that the DC voltage and ground polarity m atches the engine battery.
2) Press and hold the clock symbol key during entire time setting procedure. a) Press the Day key to bring the actual day of the week into display. b) Press the h button to set the hours and the m button to set the minutes. If the keys are depressed for more than a second, the digits will advance rapidly.
c. Turn the AUTOMATIC / MANUAL SWITCH to the AUTO position to stop the engine. Automatic Engine Cranking in TEST a. Disconnect engine wire from TB1-1 to prevent starting. b. Press the TEST PUSHBUTTON on the weekly TEST TIME R. The solenoid valve opens to discharge water, and the pressure switch contacts close to initiate cranking.
b. Wait 10 seconds for the Oil Pressure Delay interval to expire, then m omentarily jumper TB1-4 to TB1-11. The alarm will sound and the Comm on Trouble relay will energize. The LOW OIL PRESSURE LED will come on and remain on after the engine stops. c.
Troubleshooting Hazardous voltage will shock, burn, or cause death. Do not touch until ALL power is disconnected. ! DANGER W ARNING: Disconnect AC power to the Controller before servicing to prevent shock or accident hazard. Before troubleshooting, perform the following checks: a.
Table 6-1 Troubleshooting Condition Possible cause Checks Action Batteries Voltmeters should read at least 12.5 or 25 VDC Check each battery in bank for correct voltage Check electrolyte Test and rech.
Table 6-1 Troubleshooting (Continued) Condition Possible cause Checks Action Water and fuel solenoid circuits Check battery voltage Check WATER and FUEL Relay Clean and tighten connections Replace Eng.
Condition Possible cause Checks Action Engine stops without having to press STOP button or before run time is complete Water and Fuel solenoid circuits and valves, or Main Logic Board faulty Check Wat.
No HIGH ENGINE TEMP indication Water temp erature switch Connect a jumper across the water temperature switch on the engine Start engine with MANUAL START switch Verify that engine starts and alarm so.
Table 6-1 Troubleshooting (Continued) Condition Possible cause Checks Action Engine does not crank with Remote Start Cranks when water pressure decreases Remote switch faulty Main Logic Board faulty C.
.
Pressure Switch / Recorder Changing the Chart Paper First, locate the “change chart” button (#3) located in the upper left corner of the recorder. Press and hold this button for approximately one (1) second until the pen begins to move to the left of the chart.
Figure 4 Pressure Settings Start Pressure Sto p Pressure ( 3 ) Status LED’S SEE NOTE.
Battery Charger Introduction The Power Sense Board monitors the charging current a nd voltage of both chargers. LED’s indicate that the chargers are supplying current output, that the battery / charger voltage is above 90%, and that AC Power is available to power the chargers.
Troubleshooting Chart Symptom Possible cause Solution All charger LED’s off, cabinet CHARGER FAILURE indicating light on 1) No AC power 2) Charger AC fuse blown 1) Check for 120 V Charger power 2) H.
Location and Description of Control Settings.
デバイスHubbell Diesel Engine Fire Pump Controller LX3000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hubbell Diesel Engine Fire Pump Controller LX3000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHubbell Diesel Engine Fire Pump Controller LX3000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hubbell Diesel Engine Fire Pump Controller LX3000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hubbell Diesel Engine Fire Pump Controller LX3000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hubbell Diesel Engine Fire Pump Controller LX3000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHubbell Diesel Engine Fire Pump Controller LX3000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hubbell Diesel Engine Fire Pump Controller LX3000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHubbell Diesel Engine Fire Pump Controller LX3000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
