Huffyメーカー1000の使用説明書/サービス説明書
ページ先へ移動 of 18
1 03/04 P/N 211879 © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211879 03/04 W ARNING F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net.
03/04 P/N 211879 3 SAFETY I NSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
4 P/N 211879 03/04 For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
03/04 P/N 211879 5 Get to know the basic parts of your basketball system..... STRUTS BACKBOARD FRONT RIM WHEEL CARRIAGE ASSEMBL Y BASE POLE.
6 P/N 211879 03/04 P ARTS LIST - (See Hardware Identifier) Item Qty . Part No. Description 1 1 206645 T ank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 T op Pole Section 5 1 908057 Middle Pole Section with Label 6 1 908490 Bottom Pole Section 7 1 202820 Rod, 3/8 O.
03/04 P/N 211879 7 HARDW ARE IDENTIFIER (BOL TS & RODS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS & CLIPS) Item #14 (1) Item #12 (6) Item #10 (1) Item #.
8 P/N 211879 03/04 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A : ASSEMBLE THE BASE (2) 9/16” and 1/2” 9/16” and 1/2” AND/OR This is what your sys.
03/04 P/N 211879 9 1. 1 Remove contents from t ank 5” (13 cm) 2. Correctly identify each pole section and mark indicated distance from ends with t ape (not supplied) as shown. 3. IMPORT ANT! Center the alignment slot of middle pole section (5) in the lower hole of top pole section (4) as shown.
10 P/N 211879 03/04 4 5 6 WOOD SCRAP 4. IMPORT ANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark.
03/04 P/N 211879 11 10 6 7 8 6. 2 28 28 3 3 9 Install wheel axle (2) through wheel carriage (9). Inst all wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into t ank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown.
12 P/N 211879 03/04 8. 13 13 1 Secure non-secured ends of tank strut s (13) to t ank as shown. Repeat for opposite side. 13 17 12 12 16.
03/04 P/N 211879 13 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BOARD AND RIM This is what your system will look like when you’ve finishe.
14 P/N 211879 03/04 21 22 22 18 20 17 17 Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustment s will be made in S tep 3 of this section IMPORT ANT! For spring loaded rim assembly , refer to instructions included with rim hardware.
03/04 P/N 211879 15 2. SAWHORSE OR SUPPORT TABLE 26 24 23 3. While still in the horizont al position, carefully slide backboard components onto pole. Secure hardware at desired position as shown and tighten all hardware completely at this time. Support pole and tank assembly over support t able.
16 P/N 211879 03/04 4. Install clip s. CLI P “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
03/04 P/N 211879 17 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snap s into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 9.
18 P/N 211879 03/04 15 1. 10 feet (3.05 m) Carefully upright assembly . Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). 2. 30 29 27 29 Place assembled unit to desired location. Fill tank with water (30 gallons (1 14 liters)) or sand (360 lb.
デバイスHuffy 1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Huffy 1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHuffy 1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Huffy 1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Huffy 1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Huffy 1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHuffy 1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Huffy 1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHuffy 1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。