Huffyメーカー211953Cの使用説明書/サービス説明書
ページ先へ移動 of 25
1 12/03 P/N 211953C © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211953C 12/03 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
12/03 P/N 211953C 3 W ARNING F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, support braces or net.
4 P/N 211953C 12/03 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
12/03 P/N 211953C 5 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position.
6 P/N 211953C 12/03 Get to know the basic parts of your basketball system..... HUFFY HUFFY SPORTS S P O R T S SUPPOR T STRUT BACKBOARD FRONT RIM BASE POLE WHEELS ELEV A TOR SYSTEM.
12/03 P/N 211953C 7 P ARTS LIST - See Hardware Identifier P ARTS LIST - See Hardware Identifier Item Qty . Part No. Description 1 1 206336 Tank, (Gray) 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4 “ (Black) 4 1 904847 Top Pole Section 5 1 908481 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod, 3/8 O.
8 P/N 211953C 12/03 HARDW ARE IDENTIFIER (BOL TS) * You may have extra parts with this model. Item #8 (1) Item #14 (1) Item #15 (2) Item #18 (2) Item #21 (3) Item #25 (3) Item #30 (2) Item #47 (6) Ite.
12/03 P/N 211953C 9 * You may have extra parts with this model. HARDW ARE IDENTIFIER (STEEL SP ACERS & RODS) HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS &.
10 P/N 211953C 12/03 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A : ASSEMBLE THE BASE This is what your system will look like when you’ve finished this .
12/03 P/N 211953C 11 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by t apping wheel downward with hammer , snapping it into position. Repeat for opposite side, then carefully , turn t ank (1) over . Remove all contents from underside of tank.
12 P/N 211953C 12/03 IMPORT ANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3. While maintaining alignment, bounce top & middle pole assembly (4 & 5) onto lower pole section (6) as shown until top & middle pole assembly no longer moves toward taped reference mark on bottom pole.
12/03 P/N 211953C 13 Insert pole assembly into tank assembly as shown. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). DO NOT OVER TIGHTEN IMPORT ANT!: DO NOT OVER TIGHTEN IMPORT ANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
14 P/N 211953C 12/03 1 11 15 16 11 1 13 13 11 12 13 6 14 13 HUFFY HUFFY SPORTS S PO RT S 4 16 18 18 16 17 Secure strut tubes (1 1) to bottom pole section (6) as shown. Once again, carefully place unit in the side position and secure strut (1 1) to tank (1) as shown.
12/03 P/N 211953C 15 19 21 21 19 19 20 20 19 17 22 22 23 23 Attach sp acers (22, 23) to pole mount bracket (17) with bolt s (21), washers (19), and nuts (20) as shown. Tighten just until washers (19) stop moving. IMPORT ANT!: 17 16 26 24 24 27 25 FIG .
16 P/N 211953C 12/03 30 29 16 28 28 Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle part s (32, 33) to adjustment rod with screw (31), carriage bolt (30), and flange nut (16) as shown. Insert handle assembly through pole mount assembly as shown.
12/03 P/N 211953C 17 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this s.
18 P/N 211953C 12/03 16. 36 20 35 21 34 37 Install sp acers (36) onto backboard bracket s (34) with bolts (37, 21) and lock-nut s (35, 20) as shown. Assemble lower elevator tubes (40) as shown. NOTE: T est fit bolt s into holes of brackets (34) and carefully rock them in a circular motion to ream out paint from holes if necessary 17.
12/03 P/N 211953C 19 S tarting with nut s (16) flush against bracket (34), secure rim (42) and bracket to backboard. Bend bracket (34) to line up with holes in backboard and secure. 18. 19. 34 16 42 16 IMPORT AN T! : For spring loaded rim assembly , refer to instructions included with rim hardware.
20 P/N 211953C 12/03 Assemble upper elevator tubes (43) to backboard brackets (34). SAWHORSE OR SUPPORT TABLE Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY.
12/03 P/N 211953C 21 47 39 44 44 28 Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: IMPORT ANT!: DO NOT OVER TIGHTEN 40 47 38 40 39 43 38 45 43 23. 22. 39 47 43 43 40 40 38 55 55 38 38 38 Install upper elevator tubes (43) to triangle plates (45) as shown.
22 P/N 211953C 12/03 53 49 52 Roll completed assembly to desired position. Secure assembly to ground using anchor strap (52) and tie down stake (53). Fill t ank with water (approx. 30 gallons/1 15 Liters) or sand (approx. 255 lbs./1 13 kg) and snap cap (49) in place.
12/03 P/N 211953C 23 26 26. 27. 28. HUFFY HUFFY SPORTS S P O R T S 54 10 f t. (3.05 m) While holding handle, remove pin (26). Move elevator up or down to desired height. Replace pin (26) full length to lock system at desired height. Apply height and transport label (54) to front of pole as shown.
24 P/N 211953C 12/03 Install net clips. Attachez les pinces de filet au cerceau, comme illustré. Die Netzhalteklammern wie gezeigt am Korbrand anbringen. Instale los sujetadores de la red en el borde, como se muestra. Insert one “arm” of clip into ram as shown.
12/03 P/N 211953C 25 Install Net Installez le filet. Das Netz anbringen Instale la red. Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se muestra.
デバイスHuffy 211953Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Huffy 211953Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHuffy 211953Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Huffy 211953Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Huffy 211953Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Huffy 211953Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHuffy 211953Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Huffy 211953Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHuffy 211953Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
