Huffyメーカー89025の使用説明書/サービス説明書
ページ先へ移動 of 22
1 06/03 P/N 211543B Customer Service N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. A Huffy Comp any IMPORT ANT! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, problems may occur.
P/N 211543B 06/03 2 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
3 06/03 P/N 211543B 2 3 4 8 7 Assemble rims as shown below . 1 3. 5. 4. RIM ASSEMBL Y - Corner Locations 1 and 2.
P/N 211543B 06/03 4 6. W ARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. Install net clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown.
5 06/03 P/N 211543B Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 7.
P/N 211543B 06/03 6 At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure the display pole (11), slide the display wedge (12) into position as shown. Tighten the set screw (13) to lock the display pole (11) in place.
7 06/03 P/N 211543B 8 11 49 16 10. 11 . 17 30 24 52 51 49 30 12. 49 8 55 54 54 57 44 57 55 13. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. Tighten flange nuts (8) completely. Attach spacers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
P/N 211543B 06/03 8 37 14. 38 38 24 24 17 17 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly . 8 8 15. 59 27 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown .
9 06/03 P/N 211543B 17. 16. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support brackets (37) using sp acers (59), bolt (27), and nut (42) as shown. Attach backboard assembly to pole section (1 1). Install pole cap (43). NOTE: T wo people are recommended for this step.
P/N 211543B 06/03 10 19. 55 18. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55).
11 06/03 P/N 211543B 27 59 59 42 21. 29 29 23 8 8 29 REFER TO INSTRUCTIONS INCLUDED WITH RIM HARDWARE FOR RIM ASSEMBLY 23 22. Attach lower elevator tubes (29) to backboard bracket s (23) using spacers (59) bolt (27) and nut (42) as shown.
P/N 211543B 06/03 12 27 21 42 21 22 22 23. 42 21 21 27 27 29 42 43 24. Attach backboard assembly to pole section (1 1). Then install pole cap (43). NOTE: T wo people are recommended for this step.
13 06/03 P/N 211543B 42 27 29 29 47 59 59 26. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). 55 A C B T o Set Backboard Height: A. While holding handle, remove pin (55).
P/N 211543B 06/03 14 1. Attach elevator bracket (36) and reinforcement bracket (41) to pole section (1 1) using bolts (16) and nuts (8) as shown. 41 11 36 16 8 23 23 17 65 15 15 24 18 2.
15 06/03 P/N 211543B Bend top of backboard brackets (23) outward to match up with holes on backboard and secure using nuts (8) and bolt s as shown. Attach rim to backboard using using bolts and nut s (8) as shown. 27 60 60 42 3. 29 29 23 8 58 8 8 29 4.
P/N 211543B 06/03 16 20 21 42 21 56 56 5. 6. Attach upper elevator tubes (21) to backboard bracket s (23) using spacers (56) bolt (20) and nut (42) as shown. Attach backboard assembly to top pole section (1 1). Then install pole cap (43). NOTE: Tw o people are recommended for this step.
17 06/03 P/N 211543B 5 6 6 31 28 5 31 7. Fig. A Fig. B 6 Insert locking pin (28) into bracket on adjustment tube (6). Insert cross pin (5) through hole in bracket and locking pin (28) as shown in figure A.
P/N 211543B 06/03 18 28 6 31 53 28 50 31 53 8. Fig. C Insert spring (53) into back of locking pin (28) as shown. S pring (53) should rest between two small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (50) into bracket on the adjustment tube (6) as shown.
19 06/03 P/N 211543B 27 59 59 6 42 61 61 61 61 61 9. 10. 11 . 64 63 36 62 62 6 29 Attach adjustment tube to lower elevator tubes using bolt spacers and nut as shown.
P/N 211543B 06/03 20 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble 40” fan backboard as shown below with a st andard rim as shown. 40” F AN BACKBOARD ASSEMBL Y - Corner Location 4.
21 06/03 P/N 211543B Item #26 (2) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 1 200215 Cross Pin 6 1 900006 Adjustment Tube - Upper 7 16* 203113 Bolt, Hex-Flange 5/16-18 x 2.
P/N 211543B 06/03 22 Item #27 (13) Item #18 (2) Item #20 (2) Item #33 (24) Item #35 (6) 22 of 22 Item #30 (8) Item #39 (4)* Item #40 (2) Item #59 (8) Item #60 (2) HARDW ARE IDENTIFIER (BOL TS & SC.
デバイスHuffy 89025の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Huffy 89025をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHuffy 89025の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Huffy 89025の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Huffy 89025で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Huffy 89025を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHuffy 89025の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Huffy 89025に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHuffy 89025デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。