Hunterメーカー40170の使用説明書/サービス説明書
ページ先へ移動 of 33
Ele c tr on ic/M e chani c al er most a t Mo d el 40170 ins t allat ion and op erat ion manual 42998-01 01-19-2007.
2.
3 T able of Contents Important Information.................................................. 5 T ools ............................................................................ 6 Uninstalling the Existing Unit ...................................... 9 Installing the T hermostat .
4 Congratulations! T hank you for choosing a Hunter thermostat. Y our new Hunter thermostat will provide years of reliable service and year -round energy savings . Please read this manual before beginning installation and save this booklet for complete operation instructions .
5 T his thermostat is designed to work on the following heating and cooling systems: Gas – Standing Pilot Gas – Electronic Ignition Gas – F ired Boilers Gas – Millivolt Systems Oil – F ired .
6 T his thermostat includes two #8 slotted screws and two w all anchors for mounting. T o install your new thermostat, you will need the following supplies: Flat-head screwdriver ........................................................................
7 NO TICE! Do not disconnect the wir es fr om the existing thermostat before r eading these instructions . The wires must be labeled prior to r emoval to ensur e proper r econnection.
8 UNINST ALLING THE EXISTING UNIT Y RC G W Y RC G W.
9 1. T urn the system power OFF from the existing thermostat. T urn the power to the HV A C system OFF at the main power panel or at the furnace . 2. Remove the existing thermostat cover to access the wires from the w all. (Some thermostats may have multiple covers , screws or other locking devices that must be removed or disengaged.
10 UNINST ALLING THE EXISTING UNIT , CONT . if your existing thermostat is marked ... label the wire with this sticker: G / F G G W / H W W Y / C* / M Y Y RC / VC RC RC RH / R / VR / 4 RH RH 24 V olt .
11 4. Using the provided stick ers , label each wire according to the chart. (If the terminals are not labeled, contact a qualified HV A C technician.) Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identification.
12 T op Cover T hermostat.
13 INST ALLING THE THERMOST A T INST ALLING THE THERMOST A T 1. Remove the top cover from the new thermostat by pulling the two halves apart..
14 W RC Y G.
15 2. P osition the new thermostat on the w all and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter w all plate , or if there are no existing holes , level the thermostat and mark the w all for two holes .
16 INST ALLING THE THERMOST A T , CONT . G RC RH Y W B O R H R C W G B O Y.
17 INST ALLING THE THERMOST A T , CONT . CONNECTING THE WIRES 1. Loosen, but do not remove , the terminal screws . Note: A jumper wire has been provided, connecting the RC and RH terminals for systems that do not provide both an RH and RC wire. If you have both an RH and RC wire, remove this jumper .
18 INST ALLING THE THERMOST A T , CONT . HG HE HP STD HE/HG Switch HP/STD Switch.
19 A TT A CHING THE THERMOST A T 1. Locate the HE/HG switch on the w all plate . Set the switch to HG for a gas furnace or oil burner . Set the switch to HE for electric furnaces . (T he switch has no effect when the system is set to cooling mode .) 2.
20 INST ALLING THE THERMOST A T , CONT ..
21 3. Insert two fresh AA alkaline batteries . 4. Align the top cover with the the w all plate , and snap the two halves together . 5. Restore power at the electrical panel or furnace .
22 AUT O ON COOL OFF HEA T SYSTEM 9 0 0 7 0 6 0 5 8 0 F an Switch System Switch Set T emperature Slider.
23 OPERA TION 1. Set the Set Temperature slider to the desired temperature . 2. T he System Switch determines the operating mode of the thermostat. Select Cool, Off, or Heat. 3. T he Fan Switch should normally be located in the Auto position. T o run the fan continuously , slide the Fan Switch to the On position.
24 INDICA TORS AND ADUSTMENT 0 5 0 6 0 7 8 0 9 0 T hermometer Battery Indicator.
25 INDICA TORS AND ADUSTMENT 1. T he Thermometer indicates the room temperature . 2. T he Battery Indicator displays two battery conditions . T he first w arning is the Weak Battery Warning , indicated by the Battery Indicator flashing once approximately every three seconds .
26 SP AN Span Adjust SP AN.
27 INDICA TORS AND ADJUSTMENTS, CONT . 1. Remove the top cover from the thermostat. 2. T o mak e your system run LONGER, turn the Span Adjust clockwise . 3. T o mak e your system run SHOR TER, turn the Span Adjust counter clockwise . 4. Reattach the top cover to the thermostat.
28 1. My heating or cooling will not turn on or off . 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b . W ait. T here may be as much as a 4-minute delay before the system turns on or off to protect the compressor . 1 c. Check the circuit break ers and switches to ensure there is enough power to the system.
29 Is there help on the web? Y es . V isit http://www .hunterfan.com for more information. ............................................................................................. Can’t I just call someone? Sure . Our T echnical Support Group is av ailable from 8 am to 5 pm CST .
30 G Rc Rh W Y F an Relay Heat/C ool 24V Supply Cool Contactor Heat Rela y or V alve X Jumper 4-wire Heat/C ool System G Rc Rh F an Relay He at 24V Supply W Heat Relay or V alve Y Cool Contactor 5-wir.
31 WIRING DIAGRAMS Reversing V alve Compressor Contactor X F an Relay Heat/C ool 24V Supply Single-stage Heat P ump System Cool Mode Heat Mode OR W G Rc Rh O B Y X Jumper Rc R h W Heat 24V or Millivol.
32 G Rc Rh W Heat 24V Supply Heat Relay or V alve X Jumper 3-wire Heat Only S ystem F an Relay G Rc Rh W Heat 24V Supply Heat Relay or V alve X Jumper 3-wire Heat Only S ystem F an Relay G Rc Rh Y Coo.
33 © 2007 Hunter F an Company.
デバイスHunter 40170の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter 40170をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter 40170の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter 40170の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter 40170で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter 40170を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter 40170の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter 40170に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter 40170デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
